What is the p1351 ignition control module voltage?
P1351 – Ignition Control Module Circuit Voltage Trouble Code Fault Location P1351 Ignition Control Module Circuit Voltage
When does the PCM set the code p1351?
Nonetheless, regardless of the cause of the problem, the PCM will set code P1351 and illuminate a warning light when it detects an abnormal voltage in the control circuit of the Ignition Control Module. The image below shows a much-simplified schematic of a typical DIS ignition system.
What does p1351 stand for in OBD II?
END OF SPECIAL NOTES. OBD II fault code P1351 is a manufacturer specific code that most carmakers define as “Ignition Control Module Circuit Voltage”, or sometimes as “Ignition Control Module Circuit High Voltage”.
How much does it cost to diagnose a p1351 Chevy code?
The cost of diagnosing the P1351 CHEVROLET code is 1.0 hour of labor. The auto repair labor rates vary widely across the country, and even within the same city. Most auto repairs shops charge between $75 and $150 per hour. When is the P1351 CHEVROLET code detected? The Ignition Control Module (ICM) has independent power and ground circuits.
Nonetheless, regardless of the cause of the problem, the PCM will set code P1351 and illuminate a warning light when it detects an abnormal voltage in the control circuit of the Ignition Control Module. The image below shows a much-simplified schematic of a typical DIS ignition system.
END OF SPECIAL NOTES. OBD II fault code P1351 is a manufacturer specific code that most carmakers define as “Ignition Control Module Circuit Voltage”, or sometimes as “Ignition Control Module Circuit High Voltage”.
The cost of diagnosing the P1351 CHEVROLET code is 1.0 hour of labor. The auto repair labor rates vary widely across the country, and even within the same city. Most auto repairs shops charge between $75 and $150 per hour. When is the P1351 CHEVROLET code detected? The Ignition Control Module (ICM) has independent power and ground circuits.
Where is the trouble code on a GMC?
When retrieving GMC trouble codes with an OBD II scan tool, proceed as follows: 1. Connect scan tool to the 16-pin data link connector (DLC) located underneath the steering column. The connector may have a removable cover. 2. Turn the ignition on.
Can a leaking fuel pressure regulator set the p1351 code?
If it doesn’t hold, then you’ll need to check for a leaking injector causing a rich condition which would require a long crank time to clear out the excess fuel (which sets the code intermittently) before the engine willl start. It’s possible for the fuel pressure regulator to leak only when the engine is running. I’ve personally experienced that.
What are the common causes of p1351 failures?
Below are some common causes of P1351-. Damaged, burnt, shorted, disconnected, or corroded wiring and connectors. Open circuits. Defective/damaged Crankshaft Position Sensors. Defective/damaged Camshaft Position Sensors (Where applicable)
What does the p1351 code on a Chevy mean?
P1351 CHEVROLET Meaning The Ignition Control Module (ICM) has independent power and ground circuits. The circuits between the ICM and the Powertrain Control Module (PCM) consists of the following circuits: -The ignition control (IC) timing signal
How does the Ignition Control Module ( ICM ) work?
The Ignition Control Module (ICM) has independent power and ground circuits. The circuits between the ICM and the Powertrain Control Module (PCM) consists of the following circuits: The ICM sends 3X signals to the PCM, and controls the timing advance during engine cranking.
What causes a p1351 circuit to short out?
Below are some common causes of P1351- Damaged, burnt, shorted, disconnected, or corroded wiring and connectors Abnormal system voltages caused by defects, malfunctions, or failures in the charging system Failed, or failing PCM.
What does the error code p1354 stand for?
It causes the engine to idle rough and underpowered. This error code is a manufacturer-specific trouble code, meaning it does not apply to all vehicles makes. Rather, it applies only to specific vehicle makes, such as Toyota. Specification on the definition, troubleshooting, and repairs still vary from one make and model to another.
It causes the engine to idle rough and underpowered. This error code is a manufacturer-specific trouble code, meaning it does not apply to all vehicles makes. Rather, it applies only to specific vehicle makes, such as Toyota. Specification on the definition, troubleshooting, and repairs still vary from one make and model to another.
What causes a p1135 code on a Toyota?
The majority of the time, the P1135 code initiates from these causes: 1 Faulty air/fuel ratio sensor in bank 1, sensor 1 2 Air/fuel sensor harness for bank 1, sensor 1 has a short or isn’t properly connected 3 Air/fuel sensor for bank 1, sensor 1 has a poor electrical connection 4 ECM is faulty
What causes an engine trouble code of p1349?
Possible causes of trouble code P1349 include: Low or dirty engine oil. Incorrect valve timing. Faulty oil control valve. Faulty variable valve timing controlled assembly. Faulty engine control module (ECM)
Why is my Check Engine light on code p0135?
Code P0135 occurs when the powertrain control module tests the upstream heated oxygen sensor’s heater circuit on Bank 1 and detects a short in the circuit or excessive resistance in the heater circuit. What Are The Symptoms Of Code P0135? Check Engine Light is on