What is the fault code on Mercedes ML?

I scanned the ML with my new Autel DiagLink scanner and it reported the following fault codes: 5101 L6/1 (left front speed sensor) : Carry out visual inspection. CURRENT 5102 L6/1 (left front speed sensor) : Check wheel bearing (s). CURRENT 5103 L6/1 (left front speed sensor) : Carry out visual inspection.

What kind of ABS does a 2008 ML320 have?

Current 2008 320ML CDI. Previous 1998 E320, 2007 E320 Bluetec Found this. I have a 2008 ML320 (164.122), were ABS/ESP says it is not available. I already replaced ALL rpm sensors, but front left wheel is still strange.

How many control units does a Mercedes Benz have?

There are also codes for other control units such as transmission, ABS, SRS, ESP, 4ETS, airbag, A/C. Mercedes-Benz can have up to 47 control units. You can NOT diagnose them with a simple OBD-2 scanner. To read these systems and their fault codes or erase them from your Mercedes-Benz you need more advanced OBD-II scanners.

Where are sensor 1 and 2 on a Mercedes Benz?

Bank 1 Sensor 1 is the upstream (pre-cat) on the passenger side. Bank 1 Sensor 2 is the downstream (post cat) on the passenger side. Bank 2 is on the driver side. Bank 2 Sensor 1 is on the upstream (pre-cat) on the driver side. Bank 2 Sensor 2 is the downstream (post cat) on the driver side. Where is Sensor 1?

How do I remove the O2 sensor from my Mercedes Benz medic?

Once you place the O2 removal tool on the O2 sensor, you will need to turn it counterclockwise to remove it. Step 7: Install new oxygen sensor. Install the new oxygen sensor, which we showed you how to buy online for under under $100 in reverse order.

Do you need SCN code for 2010 ML350?

Unfortunately, if this is the problem, the conductor plate replacement is pretty much a dealer-only job because it contains the TCU which requires SCN coding (i.e. encrypting the VIN into it). Did you ever find a solution? I have the same code on 2010 ML350.

Where is the Diagnostic Code on a Mercedes Benz?

A hand-held tester can be connected to the underhood data link connector (DLC) X11/4 located at module box, or a generic scan tool can be connected to the generic connector X11/22 located in the tower edge of the instrument panel. To access diagnostic trouble codes, follow the tool manufacturer’s instructions.

What is the speed sensor code on my ml 350?

I scanned when I got home and got a P0721 Generic Pending Output Speed Sensor Circuit range/performance code. It’s a 2009 ML 350 w/66k miles and I do have a basic warranty sill active, but it covers the major power-train and engine parts.

Where can I find the Mercedes Benz chassis number?

Find it from the table below even without your VIN. If you talk to Mercedes Benz enthusiast they refer to their Mercedes Benz by the chassis number (model code). If you are wondering what chassis number you have take a look at the two tables below.

What are all the codes on a Mercedes Benz?

Use an advanced OBD-II code reader to read and erase Engine CEL, Transmission, ETS, ABS, Airbag and other systems. There are also codes for other control units such as transmission, ABS, SRS, ESP, 4ETS, airbag, A/C. Mercedes-Benz can have up to 47 control units. You can NOT diagnose them with a simple OBD-2 scanner.

Can you erase a fault code on a Mercedes Benz?

Can clear fault codes. Can read and erase all fault codes on Mercedes-Benz cars. Only works on MB but can perform further troubleshooting including SBC brake systems, convertible systems, Air Conditioner (A/C) system. 3. Mercedes-Benz Star Diagnostic DAS This is diagnostic scanner used at Mercedes-Benz dealerships.

Why is my Mercedes Benz ESP light not working?

Low Battery Voltage – If you have an old Mercedes-Benz battery which is not supplying the needed voltage you can cause ESP malfunctions and a variety of other problems such as ABS and ETS warnings. This is tricky because the battery may start the car just fine, but it doesn’t maintain the requried voltage while the car is running.

What happens to the emergency motor on a Mercedes Benz?

If emergency signals are no longer sent (e.g. caused by low voltage of on-board electrical system), the emergency function of P-gear will be disabled. The above motors are suitable for Mercedes-Benz emergency motor through the control module N73 Emergency-P.

When did the Mercedes-Benz ML 350 come out?

In 2002, the company Mercedes-Benz introduced the model ML 350, equipped with a 3.7-liter engine in a V6 configuration. In some markets, the ML 350 replaced the ML 320. In July 2002, on the basis of the M-class of the first generation (model ML 430 ), Papamobile was created.

When did the Mercedes Benz ML 400 CDI come out?

At the same time, the ML 430 was replaced by the ML 500 with a 5.0-liter V8 engine. For Europe, a 4.0-liter V8 turbodiesel version of the ML 400 CDI is available. In 2002, the company Mercedes-Benz introduced the model ML 350, equipped with a 3.7-liter engine in a V6 configuration. In some markets, the ML 350 replaced the ML 320.

When did the Mercedes Benz ML 430 come out?

In July 2002, on the basis of the M-class of the first generation (model ML 430 ), Papamobile was created. The company Volkswagen proposed to build a new car based on the model Touareg, but Benedict XVI decided to continue working with the company Mercedes-Benz.

What does the ABS and ESP warning light mean?

CURRENT 5102 L6/1 (left front speed sensor) : Check wheel bearing (s). CURRENT 5103 L6/1 (left front speed sensor) : Carry out visual inspection. CURRENT 5106 This fault can be ignored and erased. CURRENT Event 6001 the supply voltage of the control unit is too low (undervoltage).

What to do if your abs light is not working?

Check wire cable for any damage. If not then remove the bolt and try to remove the sensor by twisting it back and forth. Do not use screw driver to pry it up, spray with Liquid Wrench and try again. The PDF below is only shown to give you the location of the speed sensor. If the sensor is not damaged, does cleaning it usually fix the problem?

Why does my Bas light come on in my Mercedes Benz?

To reset the lights, start up your Mercedes-Benz and turn the steering wheel all the way to the right, then all the way to the left. Do this a couple of times. Turn off the engine. Restart. Brake Light Switch may cause BAS / ESP / ABS light to come on. It is the most common problem with Mercedes-Benz cars.

What does Bas ESP ABS mean on a Mercedes Benz?

What does BAS ESP ABS light mean on a Mercedes-Benz? Let’s first take a look at what each of these acronyms means. BAS stands for Brake Assist System. It provides additional braking power in case of emergency situations.

What does it mean when your abs light comes on?

This would certainly cause the ABS light to come on, which means you’d need to replace the pump right away. When the ABS light activates on your car’s dashboard, it signals that something is wrong with the anti-lock braking system.

Can a failed ABS sensor trigger the Bas light?

If you have an ABS sensor that has failed, it will also trigger the ABS, ESP, BAS light. Because the ESP system depends on the ABS system to function properly, the ESP system will also get disabled.

Why is the ESP light flashing on my Mercedes?

If pressing the ESP switch does not turn off the light, or if the ESP light is flashing, it means there is a problem with the ESP system on your Mercedes-Benz. This article will help you diagnose ESP problems on your Mercedes-Benz. Toggle ESP light on / off by pressing ESP button. Shown on SLK/Crossfire.

How do you turn off esp on a Mercedes Benz?

Well just turning ESP off via the switch doesn’t completely turn off ESP. In extreme situations ESP will still engage. You can disable ESP either via the secret menu using the multifunction buttons on the steering wheel, by using a scanner such as Mercedes-Benz DAS Star Diagnostic to disable ESP Control Unit or by removing the ABS / ESP fuse.

Navigation