What happens when you loosen a serpentine belt?
If your vehicle uses the alternator bracket to apply tension to the belt, loosen the two bolts that pass through the long eyelets on the bracket. As you loosen the bolts, the tension on the belt will likely move the alternator toward the engine and relieve the pressure. Loosen the bolts enough to move the alternator, but don’t remove them.
How do you change the serpentine belt on a Pontiac Vibe?
Serpentine belts consolidate the many belts into one, saving engine compartment space and making it easier to replace. Park the car on a flat surface, turn off the engine and allow it to cool before replacing the belt. Open the hood of the Pontiac Vibe and locate the serpentine belt.
Where do I find the serpentine belt on my car?
To access the serpentine belt, you will need to open the hood of the vehicle. The hood release can usually be found near the door on the driver’s side of the vehicle. With the hood released, you will also need to release the safety latch located at the front of the vehicle.
How do you remove a pulley belt from a car?
With the tension relieved from the belt, pull it off of the pulley that has been placing tension on it, then remove it from the around the rest of the pulleys on the engine. If the belt is severely damaged, be sure to remove any parts that may have come off of it as well. Compare the new belt to the old one.
What does it mean when your serpentine belt is slipping?
Pulleys tend to wear out or fall apart in some cases while damaged tensioners loosen the serpentine belt. Weak glow of the battery warning light When you have a weak glow on the dashboard it could mean the serpentine belt is severely slipping. In this case, the alternator is barely producing enough voltage output (hens the warning light).
How do you remove a serpentine belt from a car?
Pull the belt off of the pulleys. With the tension relieved from the belt, pull it off of the pulley that has been placing tension on it, then remove it from the around the rest of the pulleys on the engine. If the belt is severely damaged, be sure to remove any parts that may have come off of it as well.
What causes the serpentine belt to come off a Dodge Journey?
All bearings appear sound and the belt is still coming off. Vehicle is a 2012 Dodge Journey. Help please. Would a cocked tensioner cause the serpintine belt to come off. I had problem with 2000 Pontiac Montana throwing the serpentine belt.
When did the serpentine belt come off the Chrysler 3.3L?
The 3.3L and 3.8L engines are the ones with the most problems when it comes to the engine belt coming off. The model years are 1996 through 2001, but I’ve seen older and newer ones do the same thing.
What kind of pulley does a serpentine belt use?
Determine if there is a belt tensioner pulley. Depending on the application, your serpentine belt will either have tension placed on it using a movable bracket or an auto tensioner pulley. This pulley uses an internal spring to apply consistent pressure to the belt at all times.
What happens when a serpentine belt is worn?
A worn or damaged serpentine belt can fail to adequately transfer the power, leaving your alternator, power steering, and air conditioning failing to function. If your serpentine belt needs to be replaced, it can be done using only common hand tools.
Where do I find the serpentine belt routing diagram?
Find the serpentine belt routing diagram. Many cars come with a sticker in the engine bay that shows exactly how the serpentine belt is supposed to be routed through the various pulleys on the engine. If your vehicle does not have a sticker, you will need to find another way to remember how the belt should be run.
What to do if your belt is loose after routing?
If the belt is loose after routing it, it is either the wrong size belt or you’ve routed it incorrectly. Apply pressure on the auto tensioner and put the belt over it. Use the same wrench to loosen the auto tensioner pulley, then pull the belt over it. Once the belt is in place, release the pressure on the tensioner so it holds the belt in place.
How much does it cost to replace a serpentine belt?
The replacement cost is only going to be between $100 and $200 in most cases. The belt itself will cost between $25 and $80 while the labor costs will probably be between $75 and $120. Taxes and fees will be added onto these prices too. The ease of accessing the serpentine belt will determine how much the labor costs are.
How to change serpentine belt on Mitsubishi Lancer?
How to change the serpentine belt on Mitsubishi Lancer. This is the 4b11 engine that comes on the 2008 Mitsubishi Lancers. This is one of the easiest DIY mods i have done to the car, depending on your car the different tools you will need. You can find the right part at your auto store.
Where can I find a serpentine belt routing diagram?
Select the specific year and make of your vehicle. Take note of the Illustration number and then Scroll to the bottom of the page to find your Free Serpentine Belt Routing Diagram. What’s that squeal coming from under the hood?
Can You mod a 2008 Mitsubishi Lancer GTS?
Putting mods on my 2008 Mitsubishi Lancer GTS is the main focus. My goal for this channel is not only to entertain you, but to bring you value. If you want to be part of my journey don’t forget to hit that subscribe and bell button to be notify when i post!