What happens when catalytic converter is clogged in Mercedes?

If your catalytic converter is clogged you will notice a drastic drop in fuel efficiency and real struggle getting your Mercedes to accelerate. If the cat is completely clogged your car won’t even start.

What causes a cylinder to misfire in a Mercedes?

In most cases, a cylinder misfire is caused either due to old spark plugs that need to be replaced. A failed ignition coil or a bad spark plug wires. If none of the above fixes your misfire problem carefully analyze the fault codes, it is possible that misfire may be indirectly caused by another problem in the engine.

Where are misfire codes stored in a Mercedes?

Luckily for you, the misfire codes are stored in the ECU and are very easy (and inexpensive) to retrieve. To diagnose an engine misfire on a Mercedes all you need is a generic OBD II code reader that can be bought in some cases for under 20 at your local auto parts store or on Amazon’s Best Selling OBD II scanners list.

What is the trouble code for cylinder 5?

P0305 is a diagnostic trouble code (DTC) for “Cylinder 5 Misfire Detected”. This can happen for multiple reasons and a mechanic needs to diagnose the specific cause for this code to be triggered in your situation. Our certified mobile mechanics can come to your home or office to perform the Check Engine Light diagnostic.

What causes a Mercedes engine to misfire code?

It is very likely that the P0100 fault code which refers to a malfunction in the mass air flow sensor circuit is also causing the misfire codes and even a limp home mode. Lime home mode means the transmission gets stuck in gear, typically in second gear.

Can a clogged catalytic converter cause a misfire?

A catalytic converter that is clogged and is restricting the exhaust gasses from leaving the engine can also trigger multiple cylinder misfire. If your catalytic converter is clogged you will notice a drastic drop in fuel efficiency and real struggle getting your Mercedes to accelerate. If the cat is completely clogged your car won’t even start.

Why is my Mercedes Benz ESP light not working?

Low Battery Voltage – If you have an old Mercedes-Benz battery which is not supplying the needed voltage you can cause ESP malfunctions and a variety of other problems such as ABS and ETS warnings. This is tricky because the battery may start the car just fine, but it doesn’t maintain the requried voltage while the car is running.

Why is the ECU not working on my Mercedes Benz?

He specified that he just could not make a connection to the ECU at ALL; he took the time to explain that a lot of times when cars come to his shop the machine is not able to read the readiness portion for the cars to pass smog, something that can be fixed by driving the car around for several hours, but that was not the case with my car.

Why is the OBDII scanner not working on my Mercedes Benz?

When I got home I took an OBDII scanner, the same one I have used several times in the past to read the codes, and the machine did not connect at all to the car, simply the OBDII scanner does not power up. When I move the key to the ignition position the CEL light comes on as it should and goes off when the engine starts.

Why does my Mercedes Benz make a clicking noise?

It requires electrical power to crank the engine. The car makes a clicking noise but won’t start. Hint: Starter Problem or Low Battery This may seem obvious, but an old battery is the root of many headaches and can cause all sorts of malfunctions on Mercedes-Benz cars.

Why is the brake light switch on my Mercedes not working?

If you don’t see the letters on the cluster change from P to R to N, it is a good sign that the gear selector module is defective. You can buy a new brake light switch on Amazon for less than $15 USD, just do a search for Mercedes-Benz Brake Light Switches.

Why is the instrument panel on my Mercedes not working?

The instrument panel on my 2000 (update) CLK320 is refusing to work. Basically nothing works – no warning lights, no digital display, no speedo. The only things that do work are the high beam indicator lights and the indicators. The car starts and drives ok though. Checked the fuses and they all look ok.

Why is the battery on my Mercedes Benz not working?

Hint: Starter Problem or Low Battery This may seem obvious, but an old battery is the root of many headaches and can cause all sorts of malfunctions on Mercedes-Benz cars. How old is the battery on your Mercedes-Benz?

What to do when your Mercedes goes into limp mode?

You may also get a check engine light if your transmission goes into limp mode. When a Mercedes-Benz goes into limp mode, it only operates in second gear and reverse only. When you put it in gear, you may also feel a bang as transmission engages. The first thing you should try is to check the transmission fluid level.

What causes a Mercedes to go into lime home mode?

If you are reading a P0301 through P0312 code plus another code, let say P0100. It is very likely that the P0100 fault code which refers to a malfunction in the mass air flow sensor circuit is also causing the misfire codes and even a limp home mode. Lime home mode means the transmission gets stuck in gear, typically in second gear.

Are there any problems with the Mercedes ML?

Mercedes-Benz improved some designs and address several of the problems on the list above. The later models had less problems compared to the first few years of production, specifically the 1998 and 1999 model years. Another thing to keep in mind is that Mercedes-Benz ML, especially ML430 and ML500 are great truck for towing.

What kind of engine does the Mercedes ML320 have?

MLs share the M112 engine found in the ML320 and the M113 engine found on the ML430, ML350, ML500. The 722.6 gearbox installed in the ML is one of the most reliable transmission produced. ABS/ETS/ESP lights.

Is the Mercedes-Benz ML400 a good truck?

The later models had less problems compared to the first few years of production, specifically the 1998 and 1999 model years. Another thing to keep in mind is that Mercedes-Benz ML, especially ML430 and ML500 are great truck for towing. Picture M-Class, W163. If playback doesn’t begin shortly, try restarting your device.

When does the engine stall in a Mercedes?

There are never any notifications on the dash or any signs of it beginning to fail. This typically happens when I’m slowing down at an intersection or just driving slower in traffic.

Where is the shut down button on a Mercedes Benz?

This is located behind your ignition tumbler. Remove the instrument cluster and remove the switch’s connector by wiggling it out very slowly and carefully. Remove the three screws, replace the unit, reinstall the three screws and reinstall the connector.

Why does my Mercedes-Benz ml-320 shut off?

2009 ML-320 – same problem but happens very rarely, often a month between. Drive 30 minutes with a lot of stop and go. Try to restart a few minutes later, the starter turns over 10 seconds and then stops. Wait 10 minutes and it starts and works perfectly. I replaced the crankshaft sensor a few months back and it has happened twice since then.

What to do when your Mercedes Benz shuts off?

Drive 30 minutes with a lot of stop and go. Try to restart a few minutes later, the starter turns over 10 seconds and then stops. Wait 10 minutes and it starts and works perfectly. I replaced the crankshaft sensor a few months back and it has happened twice since then. 23 people found this helpful.

What causes a Mercedes Benz M class to stop?

11 people found this helpful. Hi Mark, car was stopping due to disconnection of wiring on footwell under carpet. This was caused by blockage on water vent under box below windscreen causing water to enter car down footwell. Regards, Bryan 6 people found this helpful.

What happens when a Mercedes Benz goes into limp mode?

When a Mercedes-Benz goes into limp mode, it only operates in second gear and reverse only. When you put it in gear, you may also feel a bang as transmission engages. The first thing you should try is to check the transmission fluid level. The transmission has a dipstick tube but with no dipstick in it.

How many miles does a Mercedes spark plug last?

They are wear and tear items. Standard copper spark plugs last up to 30k miles while iridium and platinum spark plugs can last over 60,000 miles. If your Mercedes-Benz has over 80,000 miles and still has the original spark plugs, it makes sense to change the spark plugs before you pour money on any other repair.

What does it mean when a Mercedes is stuck in Park?

Mercedes stuck in Park (P)and refuse to go to D or N. Stuck in D, R, N and will not move back to Park (P). Can’t remove keys from the ignition. Mercedes transmission won’t go into drive. Mercedes E, S, C, ML Class gear shift stuck in park. Mercedes will start, but transmission won’t go into gear.

Why does my Mercedes Benz hesitate to accelerate?

-Air filter and throttle body are clean. -I haven’t changed the MAF in the 2 years that I’ve owned the car, and i tried running the car with the MAF unplugged; the problem was the same except now the idle was constantly low and rough. The problem is slowly getting worse. I’m contemplating ordering a new MAF or maybe a set of new coils..

What to do if Mercedes check engine light is on?

1. Turn ignition to position II. All dash lights should be on. Don’t start the car. 2. Locate the OBD-II port under the dashboard. Location of OBD II port used to retrieve Mercedes-Benz fault codes. 3. Plug your OBD II scanner and let it turn on. Use an OBD II scanner to check why the Check Engine Light is ON.

What happens when a Mercedes engine misfire occurs?

As soon as an engine misfire occurs on a Mercedes-Benz, you will notice poor engine performance and strange vibrations that in some cases can be felt even in the driver cabin. The first thing that comes to mind when you get an engine misfire is: “This is going to be expensive.” Take a deep breath because in most cases it doesn’t have to be.

What causes a car to lose power when accelerating?

If these impurities were to get into the engine, they could cause severe damage. However, air filters tend to get clogged after they’ve been used for a while. Once an air filter gets clogged, it will limit the amount of air that can get into the internal combustion chamber.

What causes battery to die on Mercedes medic?

A defective electrical system, Control Unit or a fault on the CAN Bus (Controller Area Network) are also causes that can cause your Mercedes-Battery battery to die. To troubleshoot the current draw, you need a multimeter that can perform current reading.

How to fix a Mercedes diesel power loss problem?

For more info and related products: https://mercedessource.com/problems/f… Kent explains what he did to fix a persistent power loss problem on an old Mercedes Diesel. Once he took the fuel cap off the fuel tank he had a pretty good idea what the problem was. And this one happens more often than you would think.

Why does my Mercedes hesitate at a light?

2) when stopped at a light the idle is perfectly fine and steady except for these sudden dips in rpm and the engine rumbles/shakes, then back to normal. these dips are very random and don’t last more than a second. 3) when in reverse these same dips in rpm and shaky engine get more intense and more constant.

Why does my Mercedes Benz engine misfire so often?

Engine misfires are one of the most common problems we see in many Mercedes-Benz cars. To be honest, it is not because MB cars are weak in this area, but because most owners forget that spark plugs are wear items and need to be replaced at the recommended intervals.

How to fix no power no start on most Mercedes-Benz?

HOW TO FIX NO POWER NO START ON MOST MERCEDES-BENZ VECHICLES DIY. – YouTube HOW TO FIX NO POWER NO START ON MOST MERCEDES-BENZ VECHICLES DIY. If playback doesn’t begin shortly, try restarting your device.

What kind of engine does a Mercedes Benz have?

That is typical in Mercedes-Benz engines such as M112 M113 M272 M273 found on E, C, S, CL, CLK, ML, GL, G, R, SLK Class. For example, if you have an E320 (M112 engine) or E350 (M272) your car has six cylinders but requires 12 spark plugs.

Which is the most advanced Mercedes diesel engine?

Diesel Mercedes-Benz cars, SUV and Sprinter vans equipped with BlueTEC engines are one of the most advanced diesel engines in the world. High-pressure fuel injection system and variable geometry turbochargers ensure optimal combustion.

What happens when Mercedes diesel engine is not running?

As Mercedes DPF traps and holds soot, with time it reaches a point when it needs to be ‘emptied out’. This is done by regeneration. During this automated process, engine computer rises exhaust gasses temperature over 630°C. This burns up soot particles. However, if the engine is not running correctly automatic regeneration will not be started.

What causes soot build up in Mercedes engine?

Wrong engine oil can cause excessive soot build up. Luckily, the regeneration process can be initiated manually, using an appropriate diagnostic tool. In most cases, this will purge a clogged DPF. Mercedes, like many diesel cars, uses a DPF Exhaust Pressure Sensor to determine how much does the DPF restrict the exhaust flow.

Is it normal to make noise when accelerating?

There are noises that are normal on acceleration. The best way to know if the noise is normal is simply if you have heard the noise before. You have probably driven, or at least ridden in cars for years.

Why is my Mercedes Benz W210 running rough?

Many times, a lean running condition can be traced back to a cracked or torn boot in the system. A good quick way to check the overall health of the system is to take the oil filler cap off with the engine running. If the system is in good shape, the idle of the engine should drop and the car will run rougher.

What’s the problem with the Mercedes Benz M104?

One problem with the M104 is that corrosion develops under the coating on both the inside and outside of the valve cover. The coating on the valve cover is something similar to powder coating. I’ve been told that this coating was added to aid in sound deadening on the top of the engine.

Where does air leak in Mercedes Benz W210?

Just be sure to check all possible places air can leak in between the cylinders and the ICV. This also includes the oil dipstick O-ring, the oil filler cap, valve cover gasket, PCV valve and also the intake manifold gaskets. Sometimes, the process of eliminating all of the leaks can be quite frustrating.

Are there any problems with the Mercedes E300?

CAR WAS PARKED IN PARKING LOT, ENGINE OFF. THE MOTORIZED TRUNK LID SPONTANEOUSLY AND FORCEFULLY CLOSED ON MY HEAD, CUTTING MY FACE, WHILE I WAS LOADING (WITH BOTH HANDS) GROCERIES INTO THE TRUNK. CAR WAS PARKED IN PARKING LOT, ENGINE OFF.

What should I do if my Mercedes is overheating?

If you are able to top off the coolant, or use a bottle of water for now, it may help bring your car out of its heat spell. After you have pulled over, and if you are not the world’s most prepared driver who carries extra antifreeze in his car, give your Mercedes a break—let it cool off for about a half an hour.

What are the problems with a Mercedes Benz?

Top 5 Mercedes-Benz no start problems 1 Engine Click, No Start 2 Engine Dies Right After It Starts 3 Car turns over, but it won’t start 4 The car makes a clicking noise but won’t start. Hint: Starter Problem or Low Battery 5 Key will not turn the ignition More

Where can I pick up my Mercedes E300?

IMMEDIATELY I CALLED MERCEDES BENZ ROADSIDE ASSISTANCE AND TOLD THEM TO PICK MY CAR FROM MY BRO IN LAWS HOUSE ONCE WE REACHED.

How to troubleshoot a Mercedes Benz convertible problem?

You can also bridge the top relay for a couple of seconds to see if the hydraulic pump start to run. Replace the convertible top relay if necessary, PN 0025421319. Next, check the micro switch where the divider locks. You know that trunk separator that you are supposed to pull out and engage it in this hook?

Is there a problem with the Mercedes possition sensor?

Mercedes-Benz throttle body or throttle position sensor found on C-Class, E-Class, S-Class, CLK-Class, SLK-Class may fail causing idle issues, no idle or poor acceleration. Symptoms of defective Mercedes throttle body or throttle position sensor include: A common problem that you may notice is that the car drives fine under normal acceleration.

What causes a Mercedes Benz to not move out of Park?

If the shifter on your Mercedes-Benz will not move out of park, the first thing your should check is the battery. Once you confirm the battery is fully charged the two most common problems are a defective brake light switch or a shifter module is damaged.

Are there any problems with the Mercedes CLK320?

Tap the to learn more about the most common Mercedes-Benz CLK320 problems. The engine may stall when the engine is warmed up. The AC compressor may seize resulting in loss of cold air from the AC vents. Bulletin 13N02 – This program extends the coverage of the brake booster to ten years…

What are the most common problems with Mercedes Benz cars?

8 Most Common Mercedes-Benz Problems 1 Rust. Rust behind license plate / trunk area. 2 Engine Mounts. Engine mounts on Mercedes-Benz cars are oil filled. 3 Suspension & Steering Components. Ball joint / front control arm. 4 Window Regulators. Broken window regulator on Mercedes C-Class. 5 AirMatic Components.

What causes a Mercedes convertible to have problems?

That doesn’t mean that you can’t do a few check yourself such as checking or replacing the convertible relay or adding fluid. The majority of Mercedes convertible problems are caused by a bad relay, weak lift cylinder or lift cylinder leaking by the o-ring.

Why is my Mercedes Benz gear shift stuck?

Gear shift stuck is one of the most common problems with Mercedes-Benz cars. Unfortunately, looking to see if the brake lights turns on while you press the brake pad, is not a good test to tell if the brake light switch is working properly.

What causes a Mercedes Benz to not start?

In most cases you will get a fault code related to one of the following: 1 ECM / PCM computer failure 2 Camshaft position sensor 3 Shifter Selector module 4 Fault codes related to driver authorization or immobilizer 5 Electrical problems

What are the possible causes of a Mercedes Benz?

P0172 MERCEDES-BENZ Possible Causes Faulty front heated oxygen sensor Ignition misfiring Faulty fuel injectors Exhaust gas leaks Incorrect fuel pressure Faulty Mass Air Flow (MAF) sensor

What to do if your Mercedes FOB is not working?

Insert the key and turn it to the “ON” position, then press and release the lock button on the key. Press and hold the remote’s unlock button. In 1-2 seconds, press the remote’s lock button five times in a row while holding the unlock button. Good Luck.

Why is the clutch not engaged on my Mercedes?

Remember that the A/C clutch is controlled by the A/C Control Unit. If that unit detects an error it will not engage the A/C compressor to avoid it getting damaged. One other reason why the A/C compressor does not engage is the fact that the system may be low on R134 refrigerant.

How does fuel additives work on a Mercedes Benz?

On high mileage Mercedes-Benz cars the fuel additives will remove harmful carbon deposits from critical engine parts. Fuel additives work by removing deposits restoring lost power and performance.

What does it mean when your turn signal is not working on Mercedes?

In newer Mercedes models, you will get a warning on instrument cluster stating “Turn Signal Left / Right / Front / Rear / Side Malfunction”. Depending on the Mercedes model and problem a warning may or may not show on the dashboard.

Is there a vacuum ahead of the throttle plate?

But there is no significant vacuum at a port ahead of the throttle plate when the throttle is closed. Vacuum appears at such a port only when the throttle opens. It’s important to remember that manifold vacuum is used to power vehicle systems that need a steady supply of low-pressure air under all engine operating conditions.

How do you check engine condition with a vacuum gauge?

Experience is your best teacher. You can get a quick basic appraisal of engine condition by connecting a vacuum gauge to the manifold and a tachometer to the ignition to check vacuum and rpm at cranking speed. Warm up the engine first, then shut it down and connect your test equipment.

What should the vacuum reading be on an OBD 2?

If you’re testing an OBD II car, check for evap-related DTCs when you finish testing to be sure none set. Run the engine at idle, low cruise (1800 to 2200 rpm) and high cruise (2500 to 3000 rpm). Note the vacuum readings, and any fluctuations, at each speed.

Where is the vacuum pump on a Mercedes W123?

Return to the lines under the plastic cover at the outside edge of the driver’s side footwell. The red line that is highlighted travels straight back in to the rear driver’s side door. Pull this line from the “Y” connector, attach your vacuum pump and draw a vacuum of 10 to 15Hg on this side of the system.

What makes a Mercedes Benz vacuum go one way?

3) Switch over valve – this changes the timing of the engine based on whether the AC compressor is running or not. 4) EGR Valve – part of the emissions controls. 5) Check Valve – this keeps vacuum going one way. These fail and cause all kind of wierdness.

What causes a vacuum leak in a Mercedes 107?

Vacuum leaks in this engine cause stumbling idle, weak power, bad gas mileage and – worst case scenario – burned valves due to extremely lean running conditions. Making sure the vacuum is in order should probably be your first priority when you get a 107. Outstanding Contributor , Bob’s Your Uncle!

Why is my dashpot not working on my Mercedes vacuum?

Because the dashpot is being supplied by the 3 way connector and that is connected to the metering valve in the supply line. The metering valve is designed to restrict the vacuum going to this area. Replace the dashpot and the connector if necessary. Next we turn out attention to the big culprits to vacuum leaks.

Can a bad catalytic converter lead to engine failure?

A bad or clogged catalytic converter can ultimately lead to engine failure, so it’s important to address the issue promptly. However, having catalytic converter problems doesn’t necessarily mean that the converter has to be replaced.

When did Mercedes Benz stop using diesel engines?

In 1999, Mercedes-Benz discontinued diesel powerplants in the E-class in North America. In Europe, the diesel engines were superseded by more advanced Common Rail (CDI) units (2000–2002). The CDI engines were not offered in North America until the E 320 CDI in the newer W211 model.

When was the first Mercedes Benz E class made?

The first was the E 36, M104.995, launched in 1996 for select markets then the M119.980 in the E 50 AMG produced from early 1996 until late 1997. This model was assembled in Affalterbach under the one man one engine philosophy, only available in left hand drive European markets although many were exported to Japan from new.

What are the signs of a clogged catalytic converter?

1 Engine accelerates poorly or is hard to start. These issues could indicate a clogged catalytic converter, restricting the flow of exhaust out of the engine. 2 A sulfur or “rotten egg” smell. 3 rattling noise when starting the engine 4 Failing the annual or semi-annual emissions test 5 Vehicle warning lights.

Is the W210 a Mercedes Benz E class?

What you’re describing is the W211 (confirmed by the P/N of your aux battery). However, the W210 does not have an auxiliary battery. So ultimately this is not useful information for the W210 model, but for the W211 E class.

Are there any problems with the Mercedes engine?

Theses engines were more powerful and more fuel efficient. They did have a few teething problems but have proven to be very durable as long as they are treated and maintained properly. A true challenge – but you can do it with the right knowledge.

Can a radiator neck failure ruin a diesel engine?

Along with radiator neck failure, the rupture of one of the large oil cooler lines on your diesel engine can easily ruin your engine. When one of these lines goes you can lose all your engine oil in just a few minutes. If you are driving and not watching your oil pressure gauge you can destroy the engine bearings in short order.

How can I fix a problem with my Mercedes?

If you have a problem with your older Mercedes and are trying to figure what is causing it or how to fix it, you have come to the right place. Let Kent explain how his solutions finder works: “Just select the location of the problem you are experiencing, the chassis designation of your car and a few key words and click Search.

When did Mercedes Benz stop using cast iron?

We know that most owners can live with some looseness in the suspension, especially when you consider the age of the 123 chassis. Produced from 1984 to 1993 these lighter weight aluminum head engines replaced the venerable cast iron 616 and 617 engines of the 1970’s and early 1980’s.

What to do if you have a problem with your Mercedes Benz?

RETURN POLICY. If you are having a problem with your Mercedes Benz and you think it may be related to the ECU, feel free to post your question here and one of our technicians will respond within 24 hours. Include your email if you want a response by email.

What’s the problem with my Mercedes Benz S550?

Question: We are working on a Mercedes Benz S550 year 2007. The problem were having is that there is a misfire on cylinder 4 and 5 . We have changed the coil packs but we have the same misfire. I think the ecu that sits on the engine is the problem but Im not sure. The part number is A2731535079 .

When do you lose power on a C200?

2001 C200 Kompressor (W203) with automatic transmission loses power, sometimes when driving normally but mostly when kicking down by flooring the accelerator pedal.

How does the gas pedal work on a Mercedes?

Since 2000 Mercedes has been using drive by wire system. Which means you press the gas pedal but there is no cable connected directly to the throttle valve. Instead, there is a potentiometer that detects the position of the gas pedal.

What causes a Mercedes Benz to lose power?

and turns off the fuel to the offending cylinder resulting in power loss. Once you turn off the car and restart it resets until you trigger another misfire which as you noticed tends to happen more frequently in the beginning at WOT. Eventually the coil fails completely. So 2 more things. 1.

2001 C200 Kompressor (W203) with automatic transmission loses power, sometimes when driving normally but mostly when kicking down by flooring the accelerator pedal.

When does a Mercedes ECU throw a code?

* Mercedes ECU doesn’t count a misfire as a misfire until it misses something like 15 out of 600 firings. fuel to the cylinder it will definitely throw a code. even is it doesn’t register a code.

When to replace the throttle possition sensor on a Mercedes Benz?

If you determine the throttle position sensor has failed on your Mercedes-Benz you will need to address this problem right away. In most cases, you will get code P0120 or P012x. Your options are to replace it with a new throttle position sensor.

Is there a problem with Mercedes BlueEFFICIENCY injector?

It takes no time at all to undo a hard-won reputation (as Mercedes have already found out once to their cost) and, despite Mercedes’ assurance that they are addressing this problem, Cars UK readers are not convinced. So what do Mercedes say? We asked them for a statement and received the following:

What kind of injector does Mercedes Benz use?

Mercedes use Delphi to supply the injectors and it seems they are unable to source sufficient parts to resolve the issues, with many of our readers reporting their cars off the road for months. True, Mercedes do seem to be offering loan cars to owners who have had more than one injector failure (surely they should be doing it for everyone?).

How to check check engine light on Mercedes medic?

If you want to do more research then use Search function on Mercedes Medic or any other search engine to get a better idea of the problem. On any search engine enter the manufacturer and the code you got from the scanner. For example: Mercedes-Benz P0300

Navigation