What happens if the serpentine belt breaks on a Mercedes Benz?
If the belt breaks, your vehicle will drain the battery and the engine will eventually die. Continue reading to avoid this by learning how to replace the serpentine belt on your Mercedes-Benz E-Class or C-Class.
How do you remove tension from a serpentine belt?
Turning the tensioner counterclockwise to remove tension from the belt. Begin by routing the serpentine belt in the correct path around the pulleys. Make sure the last pulley you will be sliding the belt onto does not have raised edges; otherwise, it will be difficult to slide on.
What kind of nut does a serpentine belt use?
Small punch, cotter pin, rivet, carpentry nail etc. There are two styles of serpentine belt tensioners. The earlier (112,113 engines) style has an E10 bolt, while the newer (272,273 engines) uses a 17mm nut for adjustment.
What happens to the serpentine belt on a Mercedes Benz?
The serpentine belt powers every accessory on the engine. When it wears, belt slip occurs and it will decreases the A/C, power steering, and charging system performance. Continue reading to find out how to replace the serpentine belt on your Mercedes-Benz C-Class. This article applies to the Mercedes-Benz C-Class w204 (2007-2014).
What happens if a serpentine belt falls off?
The belt may also fall off if it is improperly routed or if it is the wrong belt. Using a gauge to check for belt wear (Image courtesy of tradetrucks.com) Have the belt replaced whenever a related component is replaced (a broken belt is often associated with a damaged or seized pulley on one of the engine accessories).
How often should a serpentine belt be replaced?
Have the belt replaced whenever a related component is replaced (a broken belt is often associated with a damaged or seized pulley on one of the engine accessories). And consider regular inspection and replacement of the serpentine belt as a part of routine vehicle maintenance every 30k miles.
Where does the bypass belt go on a Mercedes Benz?
The bypass belt will go straight from the crank pulley (#1) to the power steering pump (#3). It will just clear the top of the A/C compressor pulley (#2). As for replacing the compressor, If it’s actually the compressor pump that is the problem, you will have to recharge the system because removing the compressor does open it.
What kind of bypass belt does a clk500 use?
Most other parts, including the serpentine belt, are the same. SO, you can use the aforementioned bypass belt on your CLK500. The M112 V6 (xx240, xx320) and M113 V8 (xx430, xx500) engines what are called “modular”.
What happens when your car’s timing belt breaks?
It depends. Some cars, like Subaru, have non-interference engines, which means that if the timing belt breaks while you are driving, there is no damage to the internal parts of the engine. Other cars do not have this sort of engine and damage results.
What happens if your serpentine belt breaks in your car?
Eventually, an extremely-worn serpentine belt will break. If a drive belt breaks, you won’t be able to drive your car. This is because the engine will overheat if the water pump is not running. Also, if your car has hydraulic power steering, you will lose the steering assist, as the power steering pump will be disabled.
What happens if your drive belt breaks in your car?
Broken drive belt. If a drive belt breaks, you won’t be able to drive your car. This is because the engine will overheat if the water pump is not running. Also, if your car has hydraulic power steering, you will lose the steering assist, as the power steering pump will be disabled.
The bypass belt will go straight from the crank pulley (#1) to the power steering pump (#3). It will just clear the top of the A/C compressor pulley (#2). As for replacing the compressor, If it’s actually the compressor pump that is the problem, you will have to recharge the system because removing the compressor does open it.
How much does it cost to replace a drive belt?
One of the symptoms of a loose drive belt is a loud squealing or screeching noise that lasts for a few seconds after the engine is started. Often, drive belts are replaced as a kit with the new tensioner and other hardware. Replacing the serpentine belt may cost from $75 to $250, depending on the car.