What does the code p1582 mean on a Jaguar?
Could anyone explain what the above code means please? The code reader says “P1582 electronic throttle monitor” but my local garage couldn’t explain what it meant. It could be an old code because it was only found because I had to have the EML cleared due to another fault.
What happens if DTC p1582 is the only code?
If DTC P1582 is the only code present, it does not necessarily mean that a failure has occurred – it is more likely to be the result of a hesitation/stall event as detailed in conditions 3, 4 and 5 above. It is accepted that DTC P1582 will be present with a throttle/inertia switch failure.
What does trouble code p0332 mean on a car?
When the engine “knocks” there is an excessive amount of NOx that is released. When trouble code P0332 is set, the Power Control Module (PCM) has received a reading from knock sensor 2 in Bank 2 that is too low, and it will not be able to accurately send a ping to correct a problem.
What are the symptoms of a p0333 DTC?
Symptoms of a P0333 DTC may include: MIL (Malfunction Indicator Lamp) illumination Audible knocking from the engine compartment Pinging from engine under acceleration Potential causes of a P0333 code include: Knock sensor connector is damaged Knock sensor circuit is open or shorted to ground Knock sensor circuit is shorted to voltage
Could anyone explain what the above code means please? The code reader says “P1582 electronic throttle monitor” but my local garage couldn’t explain what it meant. It could be an old code because it was only found because I had to have the EML cleared due to another fault.
What does the p0332 code mean on a Chevy?
The P0332 code means that the Knock Sensor is not working properly. Problems with the knock sensor will not cause an engine performance problems. Replacing the knock sensor usually takes care of the problem. The cost to diagnose the P0332 CHEVROLET code is 1.0 hour of labor.
If DTC P1582 is the only code present, it does not necessarily mean that a failure has occurred – it is more likely to be the result of a hesitation/stall event as detailed in conditions 3, 4 and 5 above. It is accepted that DTC P1582 will be present with a throttle/inertia switch failure.
What are the symptoms of a p0332 DTC?
You may notice drivability problems including fluctation engine RPM, a loss of power, and perhaps some hesitation. There may also be other symptoms. Potential causes for a P0332 DTC include (but are not limited to): The knock sensor is faulty and needs to be replaced There is a wiring open/short/fault in the knock sensor circuit
What is the diagnostic code for a Jaguar check engine light?
Refer to our Generic OBD II code list for definitions on all other Jaguar diagnostic trouble codes. Manufacturer Specific Codes P1000OBD Systems Readiness Test Not Complete P1104Mass Air Flow Sensor Circuit Ground – Read Our Article On Automotive Circuit TestingFor Help With This Jaguar Check Engine Light Code P1111System Pass
How to diagnose Pats on a 2002 Jaguar?
Action: Refer to the following information when diagnosing PATS on a 2002 MY-ON X-TYPE vehicle. DIAGNOSTIC FLOWCHAR TS · P1260 – Security input (Page 2) · Passive Anti-Theft System (To be used to interpret the type of failure) (Pages 3 and 4) PATS Customer fault code flowcharts.
What is the non-customer fault code on a Jaguar?
· B1681 – fault code 11 (Pages 5, 6, 7 and 8) · B1600 – fault code 13 (Pages 9 and 10) · B1602 – fault code 14 (Pages 11, 12, 13 and 14) · B1601 – fault code 15 (Pages 15, 16 and 17) · U2511/U1900 – fault code 16 (Page 18) PATS Non-Customer fault code flowcharts.
Can you delete the error code on a Jaguar?
The code can only be deleted by Jaguar dealers apparently because its not a fault code as such but an information code. Hope this helps anyone who has the same code. You can remove it with the SDD. Mine had it once when the engine didn’t run well because of a failed lambda sensor.
What does the p1582 indicate on the throttle monitor?
Indicates actuation of restraint deployment, and Electronic Throttle Monitor data is available. The P1582 only indicates the actuation of the restraint deployment system, do not replace the Powertrain Control Module ( PCM) because there is no fault indicated.
How to diagnose p1643 jaguar can network malfunction?
Check the “Possible Causes” listed above. Visually inspect the related wiring harness and connectors. Check for damaged components and look for broken, bent, pushed out, or corroded connector’s pins. How much do you know about cars? The cost of diagnosing the P1643 JAGUAR code is 1.0 hour of labor.
How much does it cost to repair a p1643 Jaguar?
Check for damaged components and look for broken, bent, pushed out, or corroded connector’s pins. The cost of diagnosing the P1643 JAGUAR code is 1.0 hour of labor. The auto repair labor rates vary by location, your vehicle’s make and model, and even your engine type. Most auto repairs shops charge between $75 and $150 per hour.
How much does it cost to repair a p1642 Jaguar?
The cost to diagnose the P1642 JAGUAR code is 1.0 hour of labor. The auto repair’s diagnosis time and labor rates vary by location, vehicle’s make and model, and even your engine type. Most auto repair shops charge between $75 and $150 per hour.
How much does it cost to diagnose a p1642 code?
Check for damaged components and look for broken, bent, pushed out, or corroded connector’s pins. The cost of diagnosing the P1642 code is 1.0 hour of labor. The auto repair labor rates vary widely across the country, and even within the same city. Most auto repairs shops charge between $75 and $150 per hour.
What are the trouble codes for a Jaguar?
So to be 100% accurate you’ll need to refer to a service repair manual specific to your year/model/engine configuration such as Jaguar Technical Information System (JTIS) or possibly AllDataDIY. Other Jaguar-specific content on our site: Trouble codes that start with P0, P2, P34, B0, C0, U0, or U3 are all considered “generic”.