What does p0128 mean on a Dodge thermostat?
Since this often indicates a problem with the thermostat, regardless if you are driving a Dodge, a Ford, or a Jeep, the P0128 code is likely to appear once your coolant thermostat or temperature sensor fails. Of course, as was mentioned earlier, there are other potential causes for the code, as well.
What does trouble code p0128 mean on Jeep Wrangler?
Here are the symptoms associated with this trouble code: Lack of heat – The biggest symptom of the P0128 trouble code in the Jeep Wrangler is going to be lack of heat. When the thermostat doesn’t bring the engine all of the way up to the proper operating temp, it means that the water going through the heater core isn’t as hot.
Is the Jeep Wrangler p0128 coolant thermostat bad?
P0128 is not a serious threat to the immediate drivability of your Wrangler. It should be noted that most modern fuel injected engines to like to run at 200+ degrees. Letting them run too cool can problems after an extended period of time. Good luck figuring out what is going on with your Wrangler!
Why is DTC p0128 can’t clear?
Continued to drive for a few more days. I still cannot get inspected (NY) because the vehicle is showing a P0128 as a “stored” code (using Foxwell NT201 OBD reader), even though the CEL is off. Any clues on how long it takes to clear a stored code?
Here are the symptoms associated with this trouble code: Lack of heat – The biggest symptom of the P0128 trouble code in the Jeep Wrangler is going to be lack of heat. When the thermostat doesn’t bring the engine all of the way up to the proper operating temp, it means that the water going through the heater core isn’t as hot.
P0128 is not a serious threat to the immediate drivability of your Wrangler. It should be noted that most modern fuel injected engines to like to run at 200+ degrees. Letting them run too cool can problems after an extended period of time. Good luck figuring out what is going on with your Wrangler!
What to do if your thermostat says p0128?
Check for damaged components and look for broken, bent, pushed out, or corroded connector’s pins. If cooling system is not leaking and the fluid level is OK, replacing the thermostat usually takes care of the problem. What does this mean? The cost of diagnosing the P0128 JEEP code is 1.0 hour of labor.
What causes the p0128 code on a Chrysler 300?
Here are the most common causes of P0128: Thermostat Stuck Open – Far and away, the most typical cause for the P0128 code is going to be a thermostat that is stuck open. When a thermostat is stuck open, it allows coolant to flow through the engine at all times.
Since this often indicates a problem with the thermostat, regardless if you are driving a Dodge, a Ford, or a Jeep, the P0128 code is likely to appear once your coolant thermostat or temperature sensor fails. Of course, as was mentioned earlier, there are other potential causes for the code, as well.
What does the code p0128 on a check engine light mean?
You hooked up a scan tool to solve the mystery of the check engine light, and it came up with OBD-II trouble code p0128 coolant thermostat is running below the thermostat regulating temperature . So what does the code p0128 mean?
Can a p0128 coolant thermostat cause a burn?
When the engine is warm, the cooling system is pressurized and very hot and can cause burns or other personal injuries if you are not careful. Past experience indicates that the most likely solution for a P0128 is to replace the thermostat. However here are some suggestions on troubleshooting and repairing a P0128 OBD-II code:
What does the PCM error code p0128 mean?
When Error Code P0128 appears in the PCM, the engine is doing either of the two things: the engine takes too much time to warm up to its require operating temperature (takes more than 15 minutes) as measured by the Coolant Temperature sensor, or the operating temperature is below 160° – 170° F range throughout the operation of the vehicle.