What do I need to upgrade my head unit?
Purchase all the necessary parts. Depending on whether you are upgrading to an aftermarket head unit or simply replacing the old one with another OEM (original equipment manufacturer) unit, you may have to have some additional hardware. This could include things such as a dash kit, wiring harness, or antenna adapter.
Where do you plug in the head unit?
Plug in the RCA cables. RCA cables are the insulated cables that transmit the sound signal from your head unit to the amp. They should plug into the RCA ports on your head unit. If they are not already run, be sure to run these cables on the opposite side of the car as the amp’s power wire to avoid signal disruption. Set the gain on your amp.
What to do if your car head unit does not fit?
If the unit does not fit into the same space, it should have come with a modification kit to make it fit properly. If your kit did not come with this, you should purchase one from your nearest car stereo retailer. Reassemble the dashboard. Now that your head unit is back in, you can put your interior back together.
What do I need to install a car radio head unit?
Purchase all the necessary parts. Depending on whether you are upgrading to an aftermarket head unit or simply replacing the old one with another OEM (original equipment manufacturer) unit, you may have to have some additional hardware. This could include things such as a dash kit, wiring harness, or antenna adapter. Unplug your battery terminals.
Where can I get a head unit installed?
Does supercheap install head units? If you’d like to upgrade your car stereo but aren’t confident in your ability (or lack of the time to install a new head unit yourself), then you can take advantage of our installation service. It is available in a range of locations and can be booked in-store.
Do you have to disconnect battery when installing head unit?
Disconnect the negative terminal on your battery. It might not sound like much, but when you install a new head unit, you may run the risk of shorting exposed wires. Disconnecting your battery will eliminate the risk of blowing fuses during your stereo installation. Disconnect the negative terminal on your battery.
How to install a headunit Supercheap Auto head unit?
Disconnect the wiring harness from the back of the head unit by pressing down the tab to remove it. Now is an ideal time to check the harness adapter you purchased is correct for your vehicle. Disconnect the antenna. Make sure you are pulling on the connector and not the wire as this may damage it. Then, prepare the new head unit to be fitted.
Is it possible to upgrade a car head unit?
Whether you’re looking to add some of these new features to your car, installing a serious audio upgrade or simply replacing a faulty CD player, upgrading your vehicle head unit is a very rewarding project – and not as difficult as you might think.
How do you install a head unit on a car?
Connect wiring harness you prepared earlier and plug in the antenna. Slide the new head unit into the dashboard location. There are a few different positions that brackets can fit – make sure your new head unit sits flush with the surrounding trim.
Purchase all the necessary parts. Depending on whether you are upgrading to an aftermarket head unit or simply replacing the old one with another OEM (original equipment manufacturer) unit, you may have to have some additional hardware. This could include things such as a dash kit, wiring harness, or antenna adapter. Unplug your battery terminals.
How do you remove a head unit from a stereo?
Pull the original equipment stereo head unit from the center console and disconnect all of the electrical connectors plugged into it. Many original equipment stereos will have one or two harness connectors and a separate wire used for the radio’s antenna. All of these will need to be removed before the stereo can be pulled completely free.
How does a car radio head unit work?
It tells your amp when the car is on or off and prevents the amp from draining your battery. This wire will either plug directly into the back of your head unit, or need to be connected to the power supply to the head unit or another power supply. Plug in the RCA cables.
How do you connect a head unit to an amp?
Connecting your New Head Unit to an Amp Plug in the remote turn-on wire. If you have an amp in your system you want to make sure that you wire it in as well. Plug in the RCA cables. RCA cables are the insulated cables that transmit the sound signal from your head unit to the amp. Set the gain on your amp.
How to install an aftermarket head unit while?
BE VERY CAREFUL WITH THE FIBER OPTIC WIRES YOU WILL BE WORKING WITH. DO NOT kink them, they WILL break. first things first is removing the radio and CD changer.
Is the Aftermarket head unit the same as the factory mic?
The mic that’s standard in the aftermarket HU is crystal clear from what ive been told by people i’ve called. Works great for voice recognition as well. my radio included an adapter to plug into the factory mic. Great information!
Plug in the RCA cables. RCA cables are the insulated cables that transmit the sound signal from your head unit to the amp. They should plug into the RCA ports on your head unit. If they are not already run, be sure to run these cables on the opposite side of the car as the amp’s power wire to avoid signal disruption. Set the gain on your amp.
How to install a Mercedes Benz head unit?
Connect the Fiber optic plug into the avin box. I installed the box above the driver side Knee Bolster, that is removed with two screws. I also routed the GPS antenna through there, and up the driver a pillar to the windshield.