What are torque specs for Honda Accord Front suspension?
Torque Specs. As far as Torque order goes, the only thing that you need to worry about is the control arm bolts themselves. Tighten every fastener up except for the lower control arm to body bolt and the upper control arm to anchor bolt, bolts and nuts (2).
How big is the spindle nut on a Honda Accord?
242 ft-lbs on the spindle nut. Probably impossible to do without an impact or a 3/4″ torque wrench. By hand, you can’t even screw in a 10mm bolt. You need proper tools and creative tools.
How to calculate axle nut torque in Honda Accord?
Take the torque and divide by your weight 181ft-lbs / 150lbs = 1.21ft or 14.5 inches. Tighten the nut as best you can by hand, and then stand on the breaker bar at 14.5 inches from the center of the nut. I know it’s not super accurate (because you can’t stand on a single point), but it gets you pretty darn close.
How to tighten front suspension on Honda Accord?
Tighten every fastener up except for the lower control arm to body bolt and the upper control arm to anchor bolt, bolts and nuts (2). Set the car down on the ground and roll the car forward and back a couple of feet (to settle the suspension). Now tighten the remaining bolts.
Torque Specs. As far as Torque order goes, the only thing that you need to worry about is the control arm bolts themselves. Tighten every fastener up except for the lower control arm to body bolt and the upper control arm to anchor bolt, bolts and nuts (2).
What happens if your spindle nut is over torque?
It will also leave your spindle nut under or over torque resulting in hub assembly failure. Ensure that you have the correct torque for the application by referring to SKF 457377 torque specification guide or contact the vehicle manufactures dealer. It is important that you properly torque the spindle nut to ensure optimum bearing life.
Where can I find the torque specification guide?
Ensure that you have the correct torque for the application by referring to SKF 457377 torque specification guide or contact the vehicle manufactures dealer. It is important that you properly torque the spindle nut to ensure optimum bearing life. Under torque of an axle nut will allow excessive movement causing uneven loading and excessive wear.
Tighten every fastener up except for the lower control arm to body bolt and the upper control arm to anchor bolt, bolts and nuts (2). Set the car down on the ground and roll the car forward and back a couple of feet (to settle the suspension). Now tighten the remaining bolts.
What’s the torque angle on a Honda Civic?
This is called torque-to-yield, where you tighten a bolt to a certain point and then it further. This stretches the bolt and helps create a long-lasting clamping force. You may want to use a torque angle gauge to make sure you’re not over tightening. Can torque specs vary? Yes. In fact, several factors affect torque specs.
Is there a torque specifications repair guide for Commander?
Find out how to access AutoZone’s Torque Specifications Repair Guide for Commander 2006-2007. Find out how to access AutoZone’s Torque Specifications Repair Guide for 300, 300C & Magnum 2006-2008, Charger 2006-2008. Find out how to access AutoZone’s Torque Specifications Repair Guide for Cherokee, Grand Cherokee, 1999-2005.
This is called torque-to-yield, where you tighten a bolt to a certain point and then it further. This stretches the bolt and helps create a long-lasting clamping force. You may want to use a torque angle gauge to make sure you’re not over tightening. Can torque specs vary? Yes. In fact, several factors affect torque specs.
How much torque does a Honda lug nut have?
Honda Lug Nut Torque Specs Recommendations Model Trim Year Range Torque PILOT 18″BASE / LX/EX/EX-L 2016 – 2019 95 ft-lbs PRELUDE ALL / BASE/SI 1985 – 2001 80 ft-lbs RIDGELINE ALL / RTS/RTL 2006 – 2019 95 ft-lbs S2000 2 DOOR / CONVERTBLE 2000 – 2009 80 ft-lbs
Where to find torque specs for Honda Accord?
Hi Guys, I am in the middle of doing a front end overhaul on my Accord. Upper Control arm and ball joints, lower ball joints, inner and outer tie rods, sway bar end links and possibly struts. Does anyone have or know where I can find online the torque specs for all the nuts and bolts associated with this job.