What are serpentine belts on a 1998 Oldsmobile?
Most four-cylinder and six-cylinder engines used in the 1998 Oldsmobile lineup feature serpentine belts. These are one-piece belts that run the alternator, A/C compressor, power steering and water pump. These belts are easier to remove and last longer than ordinary V-belts.
How is the serpentine belt in a Chev?
Pictures, diagrams of serpentine belt routing. 2.4L. Belt Diagram 3.4 DOHC Cam Engine Drive Belt Diag… 3.5L Engine Serpentine Belt in Chev… 4.2L Inline Six Cylinder Engine Bel… 3800 V6 Belt Routing Picture and Ro…
What happens if a serpentine belt goes bad?
The serpentine belt in most modern vehicles transfers power from the crank pulley to the various accessories mounted on the engine. A worn or damaged serpentine belt can fail to adequately transfer the power, leaving your alternator, power steering, and air conditioning failing to function.
How often should I replace my serpentine belt?
These belts are easier to remove and last longer than ordinary V-belts. Always check the condition of your serpentine belt every 6,000 miles or at least twice a year. A serpentine belt that is showing cracks, fraying or other signs of wear should be replaced as soon as possible.
What’s the best way to replace a serpentine belt?
Auto tensioners have either a hole that will fit a half inch drive ratchet, or a bolt you can use a socket to apply pressure to. Insert the wrench or place the socket over the bolt on the tensioner and twist it away from the belt to relieve the tension on it.
What kind of engine has a serpentine belt?
3.5L Engine Serpentine Belt in Chev… 4.2L Inline Six Cylinder Engine Bel… 3800 V6 Belt Routing Picture and Ro… Supercharged 3.8L V6 Drive Belt rou… Vortec 5.3 and 4.8L V8 Truck Belt R…
How is the tension set on a serpentine belt?
Depending on the application, your serpentine belt will either have tension placed on it using a movable bracket or an auto tensioner pulley. This pulley uses an internal spring to apply consistent pressure to the belt at all times. If your vehicle does not have a tensioner pulley, the alternator bracket is likely how tension is set on the belt.
How often should I Check my serpentine belt?
These are one-piece belts that run the alternator, A/C compressor, power steering and water pump. These belts are easier to remove and last longer than ordinary V-belts. Always check the condition of your serpentine belt every 6,000 miles or at least twice a year.
What to do when serpentine belt is removed from car?
Start the car and observe the serpentine belt in action. Make sure the new belt is running along the pulleys properly. With the serpentine belt removed, you can also check the state of your alternator, belt tensioner and A/C compressor pulleys. These pulleys should spin freely with no noise.
Most four-cylinder and six-cylinder engines used in the 1998 Oldsmobile lineup feature serpentine belts. These are one-piece belts that run the alternator, A/C compressor, power steering and water pump. These belts are easier to remove and last longer than ordinary V-belts.
Which is the smooth side of the serpentine belt?
The kind of serpentine belt diagrams you will see on our site will be easily understandable diagrams for your make and model vehicle. The serpentine belt track to the right uses a tensioner and is from a 7.4L big-block. Notice that the smooth side of the belt is always against the smooth surface of the pulley.
These belts are easier to remove and last longer than ordinary V-belts. Always check the condition of your serpentine belt every 6,000 miles or at least twice a year. A serpentine belt that is showing cracks, fraying or other signs of wear should be replaced as soon as possible.
When was the new serpentine car belt invented?
The new serpentine belt, which was invented in 1979 is a much wider belt then the traditional automotive belt. This wider belt can be put under much tighter tension, which removes a lot of slippage and friction experienced by older belt systems.
Where do I find the serpentine belt routing diagram?
Find the serpentine belt routing diagram. Many cars come with a sticker in the engine bay that shows exactly how the serpentine belt is supposed to be routed through the various pulleys on the engine. If your vehicle does not have a sticker, you will need to find another way to remember how the belt should be run.
How do you put a serpentine belt on a car?
Slip the serpentine belt onto the pulley and slowly ease the pulley back into position. Make sure the belt is properly routed and aligned. Start the car and observe the serpentine belt in action. Make sure the new belt is running along the pulleys properly.
How do you get a belt pulley away from a belt?
Move the pulley away from the belt by inserting either a belt tensioner tool or a 3/8-inch socket wrench into the square hole at the top of the belt tensioner pulley. Slide the old belt off of the pulleys while holding the belt tensioner pulley in place.
How do you remove a serpentine belt from a car?
Pull the belt off of the pulleys. With the tension relieved from the belt, pull it off of the pulley that has been placing tension on it, then remove it from the around the rest of the pulleys on the engine. If the belt is severely damaged, be sure to remove any parts that may have come off of it as well.
Pull the belt off of the pulleys. With the tension relieved from the belt, pull it off of the pulley that has been placing tension on it, then remove it from the around the rest of the pulleys on the engine. If the belt is severely damaged, be sure to remove any parts that may have come off of it as well.
How can you tell the difference between a serpentine belt and a new belt?
Slide the old belt off of the pulleys while holding the belt tensioner pulley in place. Release the pulley after removing the belt. Compare the old serpentine belt with the new one. The new belt may be up to an inch shorter than the old one due to stretching.
How can I increase the tension on my serpentine belt?
Increase the tension on the belt. If your vehicle does not have an auto tensioner, insert a pry bar or piece of wood between the alternator and the engine. Run the belt over the alternator pulley, then use the bar to pry the alternator away from the engine and increase the tension on the belt.
Where do you replace the serpentine belt on a 2005 Chevy Uplander?
These pulleys control components such as the alternator, power steering pump, water pump and the air-conditioner pump. You can replace the serpentine belt in about 10 minutes. Pop the hood on the 2005 Chevy Uplander. Locate the serpentine belt diagram on top of the fan shroud that is covering the radiator.
How often should a serpentine belt be replaced?
And they’re crucial for running everything from alternators to power steering. In other words, when it’s time to replace it, replace it. Serpentine belts will last you a few years, but depending on whom you ask, you’ll need to start thinking about checking it every 50,000 to 60,000 miles.
Slip the serpentine belt onto the pulley and slowly ease the pulley back into position. Make sure the belt is properly routed and aligned. Start the car and observe the serpentine belt in action. Make sure the new belt is running along the pulleys properly.
Move the pulley away from the belt by inserting either a belt tensioner tool or a 3/8-inch socket wrench into the square hole at the top of the belt tensioner pulley. Slide the old belt off of the pulleys while holding the belt tensioner pulley in place.
Start the car and observe the serpentine belt in action. Make sure the new belt is running along the pulleys properly. With the serpentine belt removed, you can also check the state of your alternator, belt tensioner and A/C compressor pulleys. These pulleys should spin freely with no noise.