Is the 99 Artic cat ZR 600 EFI bad?
99 Artic Cat 500 runs great until it gets hot, then stalls, will not restart until cold- after an hour or so. Starts and runs fine. I am thinking the coil is bad … read more workshop foreman /master… Senior Mechanic & Technici…
Can a 2013 Artic Cat 500 EFI start?
Hi, I have a 2013 Artic Cat 500 EFI. It has spark, compression, & fuel (pressure is about 45lbs). It won’t start. I pulled the injector & it’s spraying fuel. … read more 99 Artic Cat 500 runs great until it gets hot, then stalls, will not restart until cold- after an hour or so. Starts and runs fine. I am thinking the coil is bad … read more
Is the Artic cat ZR 600 a tra or vocational?
Vocational, Technical or Tra… 500 Artic Cat, starts right up and runs fine until it has “warmed up”, then begins to backfire and finally stalls. Must wait foir it to cool down to restart. … read more Vocational, Technical or Tra… Vocational, Technical or Tra… Vocational, Technical or Tra… I have an Artic Cat 1997 ZR 600 EFI.
Are there still orders for 1999 Arctic Cat?
Yes! We are still quickly shipping orders! 5.0 out of 5 stars. 4.5 out of 5 stars. 4.5 out of 5 stars. Yes! We are still quickly shipping orders! Yes! We are still quickly shipping orders!
Yes! We are still quickly shipping orders! 5.0 out of 5 stars. 4.5 out of 5 stars. 4.5 out of 5 stars. Yes! We are still quickly shipping orders! Yes! We are still quickly shipping orders!
What kind of engine does an Arctic Cat have?
1998 Arctic Cat ZR 600 EFI R.H. Front Engine Mtng. Bracket., P/N 0708-044 5.0 out of 5 stars. – 1998 Arctic Cat ZR 600 EFI R.H. Front Engine Mtng.
How to prepare an Arctic Cat snowmobile for storage?
An authorized Arctic Cat Snowmobile dealer should perform this service; however, the owner/operator can perform this service if desired. To prepare the snowmobile for storage, Arctic Cat recommends the following procedure: 1. Clean the seat cushion with a damp cloth and Arctic Cat Vinyl Protectant (p/n 0638-313). 2.
What kind of gas does an Arctic Cat snowmobile use?
Recommended Gasoline (EFI Models) The recommended gasoline to use in these snowmobiles is 87 minimum octane regular unleaded, and the Fuel Designation Connector at the ECU must be connected. In many areas, oxygenates (either ethanol or MTBE) are added to the gasoline.
Why is the ZR 600 snowmobile bucking the trends?
While the rest of the industry struggled a bit for sales, one factory is making a dramatic surge forward and selling out. That company is Arctic Cat, and its surge is being led largely by the ZR 600 EFI. Why is this ZR bucking the trends?
Can a carburated snowmobile run with the EFI off?
Carburated models can be started and run with this 4-prong connector unplugged but you won’t have lights ect..as mentioned before. If you have an EFI, you can only check for spark and it will not start or run with it unplugged. You need it plugged in to power your fuel pump.
99 Artic Cat 500 runs great until it gets hot, then stalls, will not restart until cold- after an hour or so. Starts and runs fine. I am thinking the coil is bad … read more workshop foreman /master… Senior Mechanic & Technici…
Hi, I have a 2013 Artic Cat 500 EFI. It has spark, compression, & fuel (pressure is about 45lbs). It won’t start. I pulled the injector & it’s spraying fuel. … read more 99 Artic Cat 500 runs great until it gets hot, then stalls, will not restart until cold- after an hour or so. Starts and runs fine. I am thinking the coil is bad … read more
Can a bad crankshaft sensor cause the engine to stall?
If the crankshaft position sensor or its wiring have any issues, it can cause the crankshaft signal to be cut off while the engine is running, which can cause the engine to stall. This is usually a symptom of a wiring problem, however a bad crankshaft position sensor can also produce this symptom.
What to do when your EFI goes bad on a snowmobile?
The first thing to check are the connections from the stator to the cdi. Make sure all connections are free of moisture, are tight and use dielectric grease on it. Check the ground. You should have a ground wire coming from your stator and your CDI/ECU box. Make sure the ground is clean, tight and that the ground wires are not broken.