How to remove the back bench of Hyundai?

How to remove the back bench of Hyundai?

Reach between the seat cushion and back rest and pull the seat cushion up to a vertical position. Then pull the seat cushion out the drivers side rear door to remove it from its mounting bracket. Once the seat cushion is removed unbolt the folding back rest.

How do you remove the seat cushion from a Hyundai Elantra?

Remove the cushion from your Elantra. Open the trunk and find the cushion release levers in the forward corners of the trunk, right next to the trunk lid hinges. Pull on the levers and fold down both sides of the upper seat cushion. Find the mounting bolts behind each side of the upper seat cushion and remove them.

How do you remove the seat back on a Hyundai Accent?

1. After loosening the mounting bolt, then remove the rear seat cushion (A). 2. The rear center seat belt buckle (A) be removed after pushing the lock pin (B) as arrow direction. 3. After loosening the mounting bolts, then remove the rear seat back (A). 4. Installation is the reverse of removal.

How do you remove a seat cushion from a car?

First you remove the lower seat cushion, then you remove the upper seat cushion. Slide your hand into the crack between the upper and lower seat cushions. There is a bolt behind the right side of the lower cushion and the left. Remove both bolts with a socket, ratchet and 3-inch ratchet extension.

Reach between the seat cushion and back rest and pull the seat cushion up to a vertical position. Then pull the seat cushion out the drivers side rear door to remove it from its mounting bracket. Once the seat cushion is removed unbolt the folding back rest.

First you remove the lower seat cushion, then you remove the upper seat cushion. Slide your hand into the crack between the upper and lower seat cushions. There is a bolt behind the right side of the lower cushion and the left. Remove both bolts with a socket, ratchet and 3-inch ratchet extension.

Remove the cushion from your Elantra. Open the trunk and find the cushion release levers in the forward corners of the trunk, right next to the trunk lid hinges. Pull on the levers and fold down both sides of the upper seat cushion. Find the mounting bolts behind each side of the upper seat cushion and remove them.

How to repair the front seat on a Hyundai Sonata?

Repair procedures 1. Remove the seat assembly mounting cover. 2. After loosening the seat assembly mounting bolts, remove the seat assembly (A). 3. Disconnect the connectors (A). 4. Installation is the reverse of removal. Set the into the most rearward position.

How do you remove the rear seat in a Kia?

If there are no bolts, you will lift the seat to remove it. If you can find no bolts, then try the following to remove the rear seat. Lift the front part of the seat to unlatch it. Move the seat cushion back towards the trunk, then lift. Install the seat in reverse order.

How do you remove the bottom of a car seat?

If the seat bottom is not bolted push on the lower portion of the seat in between where a persons legs would be and lift up on the seat at the same time, there should be clips on both sides of the seat. Once the seat bottom is out the seat back will be bolted on its lower edges, simply remove the bolts and the seat back should lift up and out.

When did the Hyundai Trajet get a facelift?

In early 2004, the Hyundai Trajet underwent facelift – the lighting technology and the radiator grille changed, the body-colored bumper and door handles were installed. For the average passenger in the rear seat added a three-point seat belt, there was an additional interior lighting, as well as an on-board computer.

How to install a rear seat in a Hyundai Santa Fe?

Install in the reverse order of removal. 1. Remove the luggage covering met (A). 2. After loosening the mounting screws, then remove the luggage floor box (A). 3. Loosen the third row seat assembly rear mounting bolts (A). 4. Remove the third row seat track mounting cover (A). 5.

If there are no bolts, you will lift the seat to remove it. If you can find no bolts, then try the following to remove the rear seat. Lift the front part of the seat to unlatch it. Move the seat cushion back towards the trunk, then lift. Install the seat in reverse order.

How do you repair a second row seat?

Repair procedures 1. Push the second row seat assembly [RH] (A) towards the front of the vehicle as far as possible. 2. Loosen the second center seat belt buckle mounting bolt (A). 3. Push the second row seat assembly towards the front of the vehicle as far as possible. 4. Loosen the second row seat assembly rear mounting bolts (A). 5.

How do you replace the second row seat in a Kia Sorento?

1. Push the second row seat assembly [RH] (A) towards the front of the vehicle as far as possible. 2. Loosen the second center seat belt buckle mounting bolt (A). 3. Push the second row seat assembly towards the front of the vehicle as far as possible. 4. Loosen the second row seat assembly rear mounting bolts (A). 5.