How to install the timing chain on a Hyundai Elantra?
Turn the crankshaft clockwise (about 2~3 pitches) from the TDC position (the dowel pin (A) of crankshaft is about 3° with the engine vertical line) as rotation of the intake CVVT sprocket from the TDC position. 3. Install the timing chain guide (A).
How to adjust the tension on a Hyundai Elantra?
Adjust the tension by turning the tension adjusting bolt (A) clockwise. (Refer to EE group – “Alternator”) Tighten the alternator mounting bolts with the specified torque. 14. Install the engine mounting support bracket.
How to replace timing belt on Hyundai Tiburon?
1. Check the camshaft sproket, crankshaft sprocket, tensioner pulley, and idler pulley for abnormal wear, cracks, or damage. Replace as necessary. 2. Inspect the tensioner pulley and the idler pulley for easy and smooth rotation and check for play or noise. Replace as necessary. 3. Replace the pulley if there is a grease leak from its bearing.
How to install crankshaft damper pullly on Hyundai Elantra?
There are two methods to hold the ring gear when installing the crankshaft damper pullly. Install the SST (09231-2B100) to hold the ring gear after removing the starter. Install the SST (09231-3D100) to hold the ring gear after removing the service cover. 1. Remove the air guard (A).
Turn the crankshaft clockwise (about 2~3 pitches) from the TDC position (the dowel pin (A) of crankshaft is about 3° with the engine vertical line) as rotation of the intake CVVT sprocket from the TDC position. 3. Install the timing chain guide (A).
Adjust the tension by turning the tension adjusting bolt (A) clockwise. (Refer to EE group – “Alternator”) Tighten the alternator mounting bolts with the specified torque. 14. Install the engine mounting support bracket.
1. Check the camshaft sproket, crankshaft sprocket, tensioner pulley, and idler pulley for abnormal wear, cracks, or damage. Replace as necessary. 2. Inspect the tensioner pulley and the idler pulley for easy and smooth rotation and check for play or noise. Replace as necessary. 3. Replace the pulley if there is a grease leak from its bearing.
There are two methods to hold the ring gear when installing the crankshaft damper pullly. Install the SST (09231-2B100) to hold the ring gear after removing the starter. Install the SST (09231-3D100) to hold the ring gear after removing the service cover. 1. Remove the air guard (A).
Where is timing chain tensioner on Hyundai 1.8 2.0 engine?
If you have a Hyundai or Kia with a 4 cylinder 1.8 2.0 NU engine and you are trying to find where the timing chain tensioner is located this video will be helpful. This engine is used in many Kia and Hyundai cars. It should be helpful on: This is not a sponsored video. Everything is purchased by us!
Why is my crank not working on my Elantra?
The crank and cam sensors work in tandem to produce the ideal air/fuel ratio for your engine. When this timing is off, the engine will typically not run (or barely run) Here are the major symptoms of P0016 in the Elantra:
What causes a p0016 on a Hyundai Elantra?
Here are the most common causes of P0016 in the Elantra, as well as diagnostic advice, and resources to further explore. It’ll either be a wiring issue, or it’ll be a physical problem (bad reluctor or timing chain jumped). One of the most common causes of P0016 in any vehicle is going to be wiring issues.
How to turn on AM mode on Hyundai Elantra?
❈ AM Mode is not supported. Select the item to change the BASS, MIDDLE, TREBLE, FADER and BALANCE tune mode. Press the ENTER button to select each mode and rotate the VOL knob clockwise or counterclockwise. To increase the BASS, rotate the knob clockwise, while to decrease the BASS, rotate the knob counterclockwise.
How to tighten the oil drain on a Hyundai Elantra?
Tighten the oil drain bolt with the 17mm socket and a ratchet by turning it in the clockwise direction until it is snug. If you have a torque wrench, the service manual specification for properly tightening the oil drain bolt is a range of 25.3 to 32.5 lb-ft of torque.
When does the new Hyundai Elantra GT come out?
1 The Hyundai Elantra GT won’t continue after the 2020 model year. 2 The GT is a hatchback version of the brand’s compact-car offering. 3 A redesigned 2021 Hyundai Elantra sedan will go on sale later this year.
When to change the oil on a Hyundai Elantra?
This automotive maintenance tutorial was specifically written to assist owners of the 6th generation (2017, 2018, 2019, 2020 and most likely also the upcoming 2021 model year) Hyundai Elantra sedan in changing the motor oil and replacing the oil filter on the Nu MPI 2.0 liter Atkinson cycle inline four cylinder engine.