How to fix service brake system on GMC Truck?
Tighten the nut to 9 N·m (79 lb in). Cover the front and back side of the repair area using Rubberized Undercoating. An additional check can be made to ensure a good connection for the Battery Cable to Frame ground. It is possible for this ground to cause similar symptoms with the ABS as described above
Are there any recalls on GMC Yukon Denali?
The 2006 GMC or Cadillac Yukon Denali has a recall, technical service bulletins (TSB) and safety reports about the stability control on the SUV. Read more: Problems With the Traction Control on a 2006 Yukon | eHow.com http://www.ehow.com/list_7635921_problem… http://www.ehow.com/list_7635921_problem… Was this answer helpful?
How to test brake resistance on GMC Truck?
Disconnect the connector at the Electronic Brake Control Module (EBCM) and test resistance between pins A3 a Dk Green wire and B3 a Tan wire. Should be between 700-10k ohms. Compare to the pins A2 and B2. The values should be the same. 2. If an open circuit, go to the speed sensor itself, disconnect it, and check resistance across the sensor. 3.
Why is my hydraulic brake system not working?
I would call this a safety issue, I don’t agree with the dealer there at all. Your conventional (hydraulic) brake system should be working OK but you don’t have ABS or stability control, the vehicle was designed to have these systems active.
Tighten the nut to 9 N·m (79 lb in). Cover the front and back side of the repair area using Rubberized Undercoating. An additional check can be made to ensure a good connection for the Battery Cable to Frame ground. It is possible for this ground to cause similar symptoms with the ABS as described above
The 2006 GMC or Cadillac Yukon Denali has a recall, technical service bulletins (TSB) and safety reports about the stability control on the SUV. Read more: Problems With the Traction Control on a 2006 Yukon | eHow.com http://www.ehow.com/list_7635921_problem… http://www.ehow.com/list_7635921_problem… Was this answer helpful?
Disconnect the connector at the Electronic Brake Control Module (EBCM) and test resistance between pins A3 a Dk Green wire and B3 a Tan wire. Should be between 700-10k ohms. Compare to the pins A2 and B2. The values should be the same. 2. If an open circuit, go to the speed sensor itself, disconnect it, and check resistance across the sensor. 3.
I would call this a safety issue, I don’t agree with the dealer there at all. Your conventional (hydraulic) brake system should be working OK but you don’t have ABS or stability control, the vehicle was designed to have these systems active.
Is the ABS light on on my GMC Truck?
Some customers may comment that the ABS light is on. Upon further inspection, DTCs C0265 and C0201 may be set in the brake module. It is also possible for DTC U1041 to set in other modules. There may also be a loss of communication with the brake module.
Why does my brake light keep coming on?
Today the brake light came on as well with the friendly message of Service Brake System. I’m just trying to get possible ideas as to what could be causing this. No I havent had a chance to get it scanned yet, waiting on a friend.
Some customers may comment that the ABS light is on. Upon further inspection, DTCs C0265 and C0201 may be set in the brake module. It is also possible for DTC U1041 to set in other modules. There may also be a loss of communication with the brake module.
Can you disabled trailer brake system on 2015 GMC?
Hello my dash board is sending me a service for the trailer brake system it’s a GMC 2015 are we ok to drive it with that warning???? Can we disabled that?
Why does my GMC Sierra have an error message?
Can we disabled that? According to the owner’s manual for a 2015 GMC Sierra, the “Service Trailer Brake System” error message can appear on models equipped with the factory integrated trailer brake controller (ITBC) and represents a problem in the trailer brake module or wiring that will not allow power to be sent to the trailer’s brakes.
Do you need a brake replacement or service?
It is recommended that a trained professional inspect and, if necessary, service your braking system to help ensure all components are working properly and as designed. Whether you need brake service or replacement, your Certified Service technician can help you get safely—and confidently—back on the road.
How can I test my Silverado ABS brake system?
Disconnect both the front wheel speed sensor connectors at the frame and harness. Place a Digital Volt Meter (DVM) across the terminals of each wheel speed sensor connector. Rotate the wheel clockwise approximately one revolution per second. The minimum reading should be at least 350 ACmV’s.
Why are my brake calipers not releasing properly?
Water and other dust can come into the handbrake wires and cause them to rust. This will cause the brake calipers not to release properly when you release the handbrake. To fix this, you can try to lubricate the handbrake cable and the arm on the caliper and move it backward and forward a hundred times to see if it gets better.