How much does it cost to replace a valve on a Toyota Camry?
The average cost for a Toyota Camry EGR valve replacement is between $322 and $350. Labor costs are estimated between $54 and $68 while parts are priced between $269 and $283. This range does not include taxes and fees, and does not factor in your unique location.
How much does it cost to replace an EGR valve?
Replacement Cost. The cost to replace an EGR valve is anywhere from $180 to $460. The parts costs alone will be somewhere between $139 and $349. The labor costs alone will be between $50 and $120, depending on the mechanic’s hourly rate. The good news is that it should not take more than one hour for the mechanic to perform this replacement job.
Do you need Vin to replace EGR valve?
Hold on to your old EGR valve until you receive your replacement. Compare and make sure that they match. You will also need your Vehicles Identification Number (VIN) to check.
What happens when you have a bad EGR valve?
A bad EGR valve is going to cause performance problems with the engine. You will likely experience acceleration difficulties and an overall power reduction when you step on the gas pedal. This is due to the air and fuel ratio being out of whack. As a result, the engine will require more fuel just to have any power at all.
How much does it cost to replace the EGR valve on a Toyota Camry?
You just removed the original one five minutes ago, so this should be pretty easy by now. A brand new EGR valve from Toyota will cost you around $60. However, you might be able to go to your local junkyard and find your replacement there for about $15 to $20.
Where can I get a valve replacement for my Camry?
AutoZone stocks the Toyota Camry EGR valve replacement you need to get your engine running like it should. For the right prices, expert advice and perks such as free engine diagnostic testing and free battery charging, visit your local AutoZone today.
What to do if your EGR valve is damaged?
If the EGR valve for Toyota Camry is damaged, though, the combustion cycle doesn’t work properly. Keep your engine running strong for the long haul by investing in a durable EGR valve replacement from AutoZone.
What is the code for the EGR valve?
Chances are very good that you have a clogged or defective EGR valve. This might even be confirmed if your “check engine” light has come on and a simple scan reveals code PO401.
If you need to replace the valve, take off the old valve and then install a new EGR valve. You just removed the original one five minutes ago, so this should be pretty easy by now. A brand new EGR valve from Toyota will cost you around $60.
How does the vacuum switching valve on a 1998 Camry work?
by Walt Sampson. The vacuum switching valve (VSV) is a part of the exhaust gas recirculation (EGR) system of the 1998 Toyota Camry. The VSV is connected to the EGR valve. The function of the EGR system is to recirculate exhaust gases to the intake manifold of the engine and thereby reduce the nitrous oxide emissions of the vehicle (References 1).
What does the VSV do on a 1998 Toyota Camry?
The vacuum switching valve (VSV) is a part of the exhaust gas recirculation (EGR system of the 1998 Toyota Camry. The VSV is connected to the EGR valve. The function of the EGR system is to recirculate exhaust gases to the intake manifold of the engine…
Can you replace the EGR valve on a Toyota Camry?
If you need to replace the valve, take off the old valve and then install a new EGR valve. You just removed the original one five minutes ago, so this should be pretty easy by now.
When did the 1999 Toyota Camry come out?
No accident or damage reported to CARFAX. 1st owner purchased on 05/11/99 and owned in CA until 11/15/99 • 2nd owner purchased on 11/15/99 and owned in CA until 04/18/21. 1st owner drove an estimated 0 miles/year • 2nd owner drove an estimated 1,204 miles/year.
What kind of car is a 2000 Toyota Camry?
2000 Toyota Echo; 2000 Toyota Land Cruiser; 2000 Toyota MR2; 2000 Toyota RAV4; 2000 Toyota Sienna; 2000 Toyota Solara; 2000 Toyota Tacoma Regular Cab; 2000 Toyota Tacoma Xtracab; 2000 Toyota
How to test VSV and replace Toyota Camry?
Connect two vacuum pumps to the charcoal canister. Run two jumper wires from the solenoid to the 9v battery, but do not connect one of the leads. Press one of the vacuum pumps and see if it builds up any air pressure. Connect the lead to the battery. Press the vacuum pump again and check the meter. If it’s holding air, then the unit is good.
How do you clean the exhaust valve on a Toyota Camry?
Label your hoses for future reference. Once you remove the valve, take a screwdriver, a wire brush, or some other kind of scraper and clean out all the gunk as well as carbon inside the valve. Exhaust gasses will cake the inside of the valve, and with the heat of the gasses, it hardens into a very solid layer of crud.