How do you replace the ignition switch on a Chevy?
Remove the two screws from the underside of the plastic steering column cover with a Torx screwdriver turned in a counterclockwise direction. Pull the cover straight down from the bottom of the steering column. Set the cover and screws aside. Locate the black plastic J-shaped lever on the ignition switch, revealed after removing the plastic cover.
Where is the ignition switch on a GMC Jimmy?
If the mechanical assembly or contact points inside the ignition switch on your GMC Jimmy have worn out, you may have a hard time providing power to the ignition or electrical system, if at all. The switch on your Jimmy is mounted atop the steering column assembly, hiding under the dashboard.
What to do if your key is stuck in the ignition switch?
The key may be stuck in the ignition switch, but that shouldn’t stop you from turning it. If you don’t have a key, you will need to force the module to turn using a flathead screwdriver. Press the release pin inside the hole on the ignition module with a screwdriver.
Where is the pin on the ignition switch?
Slide the ignition switch off the actuating rod and remove it from the steering column. Make sure the new ignition switch is in the off position. Some aftermarket switches will have a pin on the switch slider, close to the base of the switch, to lock it in the off position to ensure proper installment. Verify whether your new switch has this pin.
What should I do if I need to replace my ignition switch?
Reconnect the cable to the negative (-) terminal on the battery, then insert the key into the ignition and turn it to start the vehicle. The vehicle should start without any issue. If it doesn’t, remove the ignition switch and reinstall it. Shut the engine off (if it starts) and disconnect the battery again.
How do you replace the ignition switch on a Silverado?
Start by inserting the two additional connectors in the harness connector (the one with the screw in the middle). Then, plug the connector in under the steering column and tighten the screw. Plug in the connector in the back of the fuze box to the left, and the small connector in the middle of the harness.
How do you remove a battery from an ignition switch?
Use an appropriate sized wrench to loosen the nut holding the cable on the negative (-) terminal and then slide it off the post. You don’t need to remove the positive cable from its terminal. Tuck the negative cable to the side of the battery to make sure it doesn’t accidentally come into contact with the terminals.
What’s the Accessory position on an ignition switch?
Insert the key and turn it to the “accessory” position. The ignition switch needs to be set to the accessory position before you can release it from the ignition module. The “accessory” position is before the starter is engaged, and would normally let you run the vehicle’s electronics without the engine running (when the battery is connected).
Where is the ignition switch on a GMC Sierra?
That is called the lock cylinder. The ignition switch typically sits directly behind the lock cylinder. It has three main functions. Power the Accessories- This should be what you get when you turn the key to the first position. This allows you to use the power windows, radio, and any other accessory that is equipped in your GMC Sierra.
How do you turn off the ignition on a Chevy Express?
Turn the ignition switch to the “Off” position. Attach the black, negative battery cable using the wrench. Turn the ignition switch to the “On” position and make sure the Air Bag indicator, on the instrument panel, flashes and then turn “Off” the ignition switch.
Is the ignition switch on a Chevy Suburban?
Chevrolet is known for using duplicate parts on many models of vehicles. You can use the following repair information on the 1500 and 2500 of the C and K series Suburbans. The ignition switch in your truck has a dual purpose: to start the engine and to provide security against it being stolen.
That is called the lock cylinder. The ignition switch typically sits directly behind the lock cylinder. It has three main functions. Power the Accessories- This should be what you get when you turn the key to the first position. This allows you to use the power windows, radio, and any other accessory that is equipped in your GMC Sierra.
What are the symptoms of a bad ignition switch?
We’ve compiled some of the most common symptoms of a bad ignition switch . These include stalling issues, not starting, and no power to the radio or accessories. The Sierra’s ignition switch is not what your key goes into.
Where is the release pin on an ignition switch?
The new or rebuilt switch should slide easily back into its hole on the steering column. Align the shape of the cylinder and the location of the release pin with the coinciding grooves in the ignition module.