How do you replace the flywheel on a Honda Civic?
Use the following steps to replace the flywheel and clutch on your Honda Civic. The quickest way to reach the clutch is from underneath the chassis. In order to do this, use a jack to raise the vehicle and a pair of jack stands to support the chassis in the air. Also use this as an opportunity to drain the transmission fluid. Figure 1.
How do you replace the clutch on a Honda Civic?
The rear transmission mount is held in by a 17mm bolt and the starter has two 14mm bolts, a wire clip, and a 12mm cable nut. The slave cylinder assembly is held in place by two 12mm bolts. Figure 11. Remove bolts for rear torsion mount. Figure 12. Remove the starter bolts. Figure 13. Remove the clutch line bracket. Figure 14.
Where is the pressure plate on a Honda Civic?
Take the pressure plate and mount it on top of the clutch plate. Position the pressure plate so the three studs on the flywheel are visible. Once fitted, tighten the pressure plate bolts to 19 ft/lbs using a criss-cross pattern.
Where are the transmission bolts on a Honda Civic?
Remove the transmission top mount’s 17mm bolts. Proceed to remove the front transmission mount (three 17mm bolts and two 14mm bolts). Remove the final 19mm mount bolt located behind the transmission. Once done, loosen all four bolts that connect the transmission housing to the engine.
Use the following steps to replace the flywheel and clutch on your Honda Civic. The quickest way to reach the clutch is from underneath the chassis. In order to do this, use a jack to raise the vehicle and a pair of jack stands to support the chassis in the air. Also use this as an opportunity to drain the transmission fluid. Figure 1.
What kind of clutch does a Honda Civic have?
This article breaks down a complicated process and takes you step-by-step in how to correctly replace the flywheel and clutch on your Honda Civic. This article applies to the Honda Civic (1992-2000). Your Honda Civic uses a hydraulic clutch system to engage the transmission into the gears.
How long does it take to replace clutch on civic?
I can do this particular car in around 3-4 hours if I don’t get distracted. Realistically, you should give yourself 8-10 hours of actual work time plus whatever you spend fixing as you go. There are probably several different ways to approach this kind of work depending on the equipment available to you.
Do you need wheel chocks for Honda Civic?
Wheel chocks are not optional. If the car rolls and falls off of the jackstands onto you, you will die. Use a hydraulic jack rated for at least twice the full weight of the car. (1.5 tons X 2) – Cardboard to work on. Get several sheets.
What happens if you don’t replace your flywheel?
You may start to experience grinding noises from the pressure plate and eventually, the flywheel other parts in the clutch assembly will overheat and cause them to warp or even crack. Finally, if the clutch and flywheel are not replaced, you simply won’t be able to shift at all.
What kind of wrench do I need to remove belt on Honda Accord?
A serpentine belt wrench is definitely optimal here, but a very long handled 12 mm open ended box wrench will work as well. You may need a second person for this part of the job. Put the wrench on the nut in the center of the pulley, and crank back on it clockwise with a significant amount of force. This will loosen the belt for removal. Figure 2.
What’s the best way to remove a flywheel?
Remove the flywheel bolts. When removing the flywheel bolts, it is best to use an impact wrench as the flywheel itself will lean, making the removal more difficult than it needs to be. Grab the pilot bearing and use a hammer and socket to press it into the new flywheel.
The rear transmission mount is held in by a 17mm bolt and the starter has two 14mm bolts, a wire clip, and a 12mm cable nut. The slave cylinder assembly is held in place by two 12mm bolts. Figure 11. Remove bolts for rear torsion mount. Figure 12. Remove the starter bolts. Figure 13. Remove the clutch line bracket. Figure 14.
Take the pressure plate and mount it on top of the clutch plate. Position the pressure plate so the three studs on the flywheel are visible. Once fitted, tighten the pressure plate bolts to 19 ft/lbs using a criss-cross pattern.
Can a bad flex plate be replaced with a new one?
A bad flex plate usually has failed due to either damage or wear and tear, so replacement with a new flex plate is the only solution. Because the flex plate is an integral part of your car’s powertrain, and replacing it involves removing the transmission, a significant amount of labor will be involved.
This article breaks down a complicated process and takes you step-by-step in how to correctly replace the flywheel and clutch on your Honda Civic. This article applies to the Honda Civic (1992-2000). Your Honda Civic uses a hydraulic clutch system to engage the transmission into the gears.
When do I need to change the flywheel?
You will rarely need to replace the flywheel, but the flywheel should be resurfaced whenever the clutch disc is replaced in a high-mileage car, and that can be easily done when the clutch assembly has been removed.
Is the clutch disc the same as the flywheel?
Clutch The clutch assembly consists of the clutch arm or actuator, the clutch disc and the release bearing. The flywheel is the interface between the clutch mechanism and the transmission. The clutch disc can become worn; this is a normal consequence of driving, and will occur at intervals of 60,000-100,000 miles, depending on driving conditions.
Why does clutch not disengage Honda Civic 19?
If you have the correct amount of free travel and have bled out all the air from the system then you have a defective pressure plate. When you have the transmission removed you need to verify the pressure plate tightened all the way to the flywheel. Make sure attachment bolts did not bottom out before…
You will rarely need to replace the flywheel, but the flywheel should be resurfaced whenever the clutch disc is replaced in a high-mileage car, and that can be easily done when the clutch assembly has been removed.
Clutch The clutch assembly consists of the clutch arm or actuator, the clutch disc and the release bearing. The flywheel is the interface between the clutch mechanism and the transmission. The clutch disc can become worn; this is a normal consequence of driving, and will occur at intervals of 60,000-100,000 miles, depending on driving conditions.
Remove the transmission top mount’s 17mm bolts. Proceed to remove the front transmission mount (three 17mm bolts and two 14mm bolts). Remove the final 19mm mount bolt located behind the transmission. Once done, loosen all four bolts that connect the transmission housing to the engine.
What do I need to replace clutch on Honda Civic?
The 21mm deep socket is for the wheels, you can use the tire tool in the trunk. The 10mm and 17mm 12-point sockets are required to remove the pressure plate and flywheel bolts. – Funnel with long hose; Electrical tape; Hammer (any kind); Dead-blow hammer or Rubber mallet; 5mm hex key (allen wrench);Small screwdriver or mechanics pick; Pry bar.
Wheel chocks are not optional. If the car rolls and falls off of the jackstands onto you, you will die. Use a hydraulic jack rated for at least twice the full weight of the car. (1.5 tons X 2) – Cardboard to work on. Get several sheets.