How do you replace a radiator drainage plug?
This is a short tutorial video on how to replace your radiator drainage plug. Mine snapped off because it is plastic so I had to figure out a way to replace it. Vehicle: Used a Ford Ranger but process can likely be used in many scenarios. Supplies needed: Needle nose pliers, bucket, replacement plug. Loading…
How to remove a radiator from a combi system?
Ok, fully close both valves* on the faulty-bleed-screw rad. Remove your bleed screw complete with plug surround. Slacken a valve to rad joint and get ready to catch the escaping water from the rad. Drain off an amount similar to the quant of inhibitor you are going to use – you can get concentrated solutions, so won’t have to add as much.
How to replace drainage plug-stop the leak?
How to Replace Radiator Drainage Plug – Stop the Leak! – YouTube How to Replace Radiator Drainage Plug – Stop the Leak! If playback doesn’t begin shortly, try restarting your device.
What happens when bleed screw is stuck on radiator?
If your bleed screw is stuck in the surrounding ‘plug’, then it’ll have to be released/replaced as you won;t be able to bleed that rad properly without it – allowing air to escape until the point where water pours out the plug won;t be good enough as it’ll be at a lower level than the bleed screw itself.
This is a short tutorial video on how to replace your radiator drainage plug. Mine snapped off because it is plastic so I had to figure out a way to replace it. Vehicle: Used a Ford Ranger but process can likely be used in many scenarios. Supplies needed: Needle nose pliers, bucket, replacement plug. Loading…
Ok, fully close both valves* on the faulty-bleed-screw rad. Remove your bleed screw complete with plug surround. Slacken a valve to rad joint and get ready to catch the escaping water from the rad. Drain off an amount similar to the quant of inhibitor you are going to use – you can get concentrated solutions, so won’t have to add as much.
If your bleed screw is stuck in the surrounding ‘plug’, then it’ll have to be released/replaced as you won;t be able to bleed that rad properly without it – allowing air to escape until the point where water pours out the plug won;t be good enough as it’ll be at a lower level than the bleed screw itself.
What happens when you remove the coolant plug on a radiator?
As the plug is being removed, coolant will start to escape from the threads. Just like most plugs, the coolant plug was hard to remove and coolant travels down the tool and down the mechanics arm making a large mess. Today, vehicles have aluminum radiators with plastic (carbon fiber) tubes.
Can you put coolant on a Jeep Grand Cherokee?
We are still working to obtain content for your car, however the video above is believed to have similar characteristics as your car. Adding engine coolant (also known as antifreeze) to your 2003 Jeep Grand Cherokee is pretty easy. Engine coolant circulates through your engine to keep it cool in the summer but won’t freeze in the winter.
How to add coolant to a Jeep Liberty?
Be sure to check your owners manual to determine the correct type of fluid to add – for Jeeps, it will typically be in a section titled Fluid Capacities in the back of your manual. Mix the coolant with distilled water so that you have a combination of 50% coolant and 50% water.
Where is the drain plug on a Jeep Grand Cherokee?
Put on your safety glasses and crawl under the Jeep on a creeper to locate the radiator drain plug. On a 4.0 liter engine, it will be on the right (passenger side) side of the inside of the radiator and on a 4.7 liter engine, it will be on the left (driver’s side) side of the inside of the radiator.
Can you drain the radiator on a Jeep Grand Cherokee?
Draining the radiator on your Jeep Grand Cherokee is not overly difficult and by doing it yourself, you can save money. Draining and filling your radiator is a low-line maintenance procedure with the understanding that you’re not replacing all the coolant in your system.
How do you remove coolant from a Jeep Grand Cherokee?
To properly remove and replace coolant from any vehicle, follow these steps. Do not drain the coolant from your Jeep Grand Cherokee until the engine and coolant have cooled down. This is not something you should attempt to perform after taking a trip to the parts store to get more coolant to replace or any other errands.
Be sure to check your owners manual to determine the correct type of fluid to add – for Jeeps, it will typically be in a section titled Fluid Capacities in the back of your manual. Mix the coolant with distilled water so that you have a combination of 50% coolant and 50% water.
Is the radiator drain plug on a Ford Mondeo?
Following on from here, kind of: http://www.fordownersclub.com/forums/topic/47311-argh-this-flippin-car/ I didn’t change the radiator as the repair, as ugly as it was, seemed to be structurally fine. Today my wife was just off to her mate’s house, as she reversed back I noticed a small puddle under the front of the car.
Why is there no water coming out of the radiator?
Popped the bonnet and had a look at the repair – put my finger under the bottom of the pipe, barely touched it and BOSH – off it came. It had completely decayed and felt just like paper. There was no gush of water, though, telling me that it’s been on the way for some time.
What to do when radiator drains in Chevy Silverado?
Add more 50/50 mix as the reservoir drains down. No matter how long you drain it, there is still some water remaining in your engine block. Some mechanics and DIY’ers fill the reservoir to the fill line with straight coolant in order to boost the engine’s overall coolant mixture to the desired 50/50.
What does it mean to drain and fill a radiator?
The traditional coolant draining process is also known as “drain and fill.” This involves simply draining the coolant at the bottom of the radiator, then topping up the radiator with fresh fluid until it it’s full.
Which is better coolant drain or flush radiator?
This involves simply draining the coolant at the bottom of the radiator, then topping up the radiator with fresh fluid until it it’s full. It’s quick and easy, and while it doesn’t remove all of the old coolant from your system, it is often all that’s necessary to keep your cooling system healthy. What is a coolant flush?
When to change radiator coolant in Chevy Silverado?
Some say it works fine and you can even wait to change your coolant until 150K miles. Others say it is a poison to your engine’s cooling ability, and even causes rapid degeneration of gaskets as well as seals.