How do you remove the door panel on a Mercedes?
There is a square clip near the lock that secures the door panel to the frame. Gently pull the door panel out. Then, insert the pliers into the crack between the panel and the frame. Push down on the peg release mechanism of the square clip, and remove it.
How do you remove a plastic door handle?
Remove the Phillips screw from behind the panel. Use the flat screwdriver to gently pry off the plastic square from around the door lock knob. Pry off the plastic surrounding the door handle also. Pull on a bottom corner of the door panel with your hands. Pry it up along the edges to pop the plastic clips loose from the door.
How do you remove trim from a door?
Open the door and use a trim removal tool to pry out the armrest cover. Remove the two Hex screws with your T27 Torx screwdriver. Use the trim removal tool to pry out and loosen the A-pillar tweeter housing. The trim can then be gently removed by hand. Figure 1. Remove the door panel covers. Figure 2. Remove the A-pillar tweeter housing.
How do you take a door panel out of a Cadillac?
Reach behind the door panel and unplug the wiring harness that connects the door to the underside of the electric window and door lock controls. Use a small container to keep the screws and small parts inside to keep them all in one place. These parts are needed for reinstalling the door panel.
What should I remove from my front door panel?
Generally speaking, the first thing to do is remove any devices that are bolted directly to the door panel itself: door lock buttons, armrests, window cranks or switches, bezels, grab handles, and removable trim pieces. Typically, the piece or the entire assembly can be removed with one or two screws at the most.
How do you remove front door panel on Hyundai Elantra?
Using a flat screwdriver to remove the front door side mirror inner cover. Remove two Phillips screws that hold the door panel in place. One of the screws is near the door handle. The second screw that needs to be removed is in the center of the door panel.
When to remove the door panels on a Jeep Liberty?
This automotive “how-to” guide was specifically written to assist owners of the 2nd generation 2008, 2009, 2010, 2011 & 2012 Jeep Liberty in removing the interior door panels in order to upgrade the OEM speaker, add soundproofing material, or replace the power window motor.
How do you remove the passenger side mirror?
These instructions are shown on the front driver’s door panel, but the passenger and rear panels can be removed following the same method. Using a flat screwdriver to remove the front door side mirror inner cover. Remove two Phillips screws that hold the door panel in place. One of the screws is near the door handle.
There is a square clip near the lock that secures the door panel to the frame. Gently pull the door panel out. Then, insert the pliers into the crack between the panel and the frame. Push down on the peg release mechanism of the square clip, and remove it.
Open the door and use a trim removal tool to pry out the armrest cover. Remove the two Hex screws with your T27 Torx screwdriver. Use the trim removal tool to pry out and loosen the A-pillar tweeter housing. The trim can then be gently removed by hand. Figure 1. Remove the door panel covers. Figure 2. Remove the A-pillar tweeter housing.
How long does it take to remove a door panel?
Removing the door panel is an easy task that you can accomplish in as little as 20 min. You will need a set of Torx sockets. To remove the door panel, you will need your screwdrivers, trim plastic wedge but also must have Torx Bit Socket Set if you need to take any other componenet off the door.
How do you install aftermarket speakers on a Mercedes Benz?
To install aftermarket speakers, you must separate the stock speakers from their mounting brackets. These mounting brackets will be installed onto the new speaker units. With a Phillips screwdriver, remove three screws surrounding the stock speaker. Use a flat head screwdriver to pry out the speaker from the door frame.
What’s the best way to remove a car door?
Pry off the cover at the edge of the window with a screwdriver. Look for a small, triangular cover piece at the top edge of the door panel, where the window connects to it. Wedge your fingers into the edge of the cover piece and gently pull against it to remove it.
Where are the screws on the door panel?
The mounting screws on the door panel are located under the armrest cover. First, disconnect the negative lead (black) from the battery terminal. Open the door and use a trim removal tool to pry out the armrest cover. Remove the two Hex screws with your T27 Torx screwdriver.
What’s the best way to remove a door panel?
Use a pair of pliers to get a good grip on the latch and then gently, but firmly pull the latch away from the panel. Don’t yank or twist the latch or you could damage the connecting clips. Be careful not to squeeze the latch too hard with the pliers or you could crack or crush it.
The mounting screws on the door panel are located under the armrest cover. First, disconnect the negative lead (black) from the battery terminal. Open the door and use a trim removal tool to pry out the armrest cover. Remove the two Hex screws with your T27 Torx screwdriver.
How do you remove a window from a car?
Some cars may have a manual window crank that needs to be removed. Take a metal pick tool and wedge it behind the crank. Locate the small clip wire holding it in place and slide it out from behind the crank. Then, pull the crank straight out with your hands to remove it.
Where are the clips on a Mercedes C class door?
Behind the edges of the door panel are nine plastic clips. One clip (located near the door lock pin) is a different type of clip from the other eight. Beginning with the side closest to the door hinges, pry out the door panel with a trim removal tool. You should hear each clip pop out.
Do you need to remove the front door panel?
It can take a tremendous amount of abuse and sooner or later something will fail, and if it is not something on the door panel it will be one of the components behind it. If you need to service your doors’ mechanicals or want to freshen up the appearance with new trim you will need to remove the door panel.
How do you remove a door clip from a door?
You should hear each clip pop out. When removing the clips, work your way from the bottom door panel to the end of the door. Once the clips are freed, firmly hold the door panel from two opposing ends. Lift the door panel up, and gently pull it outward. Do not yank the panel off as there are connectors attached to it. Figure 2.