How do you remove power steering pump from Lexus LS400?
8) Place matchmarks on the lid and reservoir itself then remove the metal lid on the top of the reservoir. There are metal tabs that hold the lid on around the circumference of the reservoir that need to be bent out in order to remove it.
Where is the air control valve on a Lexus LS400?
Please try again later. This short video shows you how fix a common leak found in Lexus LS 400 Air Control Valve located on a side of the power steering pump by reusing original parts, also if you just installed a new air control valve at the end you will find how to check that it is working properly. Loading…
How do you replace the return hose on a Lexus LS400?
If the return hose has never been replaced now is a great time to do so. Just buy a couple feet of 3/8″ hose from your local auto store, then fully remove the old hose and cut the new hose to the same length. Use new hose clamps on the return line.
How do you remove a power steering pump?
Take the ACV to your local hardware store and find an identically threaded and sized bolt to plug the ACV hole on the pump. Just for good measure I threw some high-temp RTV silicone on the threads of the bolt to be sure it wouldn’t leak. Remove the two hoses that used connect to the ACV prongs and cap off the locations on the block and intake.
8) Place matchmarks on the lid and reservoir itself then remove the metal lid on the top of the reservoir. There are metal tabs that hold the lid on around the circumference of the reservoir that need to be bent out in order to remove it.
Please try again later. This short video shows you how fix a common leak found in Lexus LS 400 Air Control Valve located on a side of the power steering pump by reusing original parts, also if you just installed a new air control valve at the end you will find how to check that it is working properly. Loading…
What to do if your power steering fluid is leaking?
Most power steering reservoirs will have a dip stick attached to the bottom of the cap. Check the power steering fluid reseviour level every few days using this dip stick. If you notice it dropping consistently, you have a power steering fluid leak.
Where does the power steering fluid come from?
Power steering fluid can be one of the most difficult leaks to diagnose. The Power steering system consists mainly of the pump, which is bolted to the motor, a feed and return line, sometimes a cooler and the power steering rack or gear.
How big is torque nut on Lexus LS400?
Torque, nut = 32 ft-lb (440 kg-cm, 43 N-m), bolt = 29 ft-lb (400 kg-cm, 39 N-m) 13) Remove the remaining two bolts that hold the pump onto the side of the engine block. These can be tough and its nice to have a long-handled socket wrench or breaker bar to get them loose.
Take the ACV to your local hardware store and find an identically threaded and sized bolt to plug the ACV hole on the pump. Just for good measure I threw some high-temp RTV silicone on the threads of the bolt to be sure it wouldn’t leak. Remove the two hoses that used connect to the ACV prongs and cap off the locations on the block and intake.
Torque, nut = 32 ft-lb (440 kg-cm, 43 N-m), bolt = 29 ft-lb (400 kg-cm, 39 N-m) 13) Remove the remaining two bolts that hold the pump onto the side of the engine block. These can be tough and its nice to have a long-handled socket wrench or breaker bar to get them loose.
If the return hose has never been replaced now is a great time to do so. Just buy a couple feet of 3/8″ hose from your local auto store, then fully remove the old hose and cut the new hose to the same length. Use new hose clamps on the return line.
How do you replace the lower ball joint on a Lexus LS400?
Fully push the upper ball joint bolt out and lift the steering knuckle off the lower ball joint and set it aside. 7) Remove the front shock, follow steps 5-6 here. Set the shock aside. 8) Remove the clip and 17mm nut on the lower ball joint.
How do you remove the steering knuckle from a Lexus LS400?
Torque = 48 ft-lb (65 Nm). 6) Using a ball joint puller, remove the steering knuckle from the upper ball joint. Just tighten the puller with a 19mm socket (for Autozone puller) and the ball joint will pop out. Fully push the upper ball joint bolt out and lift the steering knuckle off the lower ball joint and set it aside.
How much torque does a Lexus LS400 have?
Torque = None specified, just tighten both bolts and make sure the sensor is flush on the metal. 4) Using an impact wrench or breaker bar, remove the two 17mm bolts from the lower ball joint. The axle assembly won’t slip off of the lower ball joint with these bolts removed, you’ll see why. Torque = 83 ft-lb (113 Nm).
How do you replace the brake caliper on a Lexus LS400?
Check with your parts supplier for the correct part numbers because they vary depending on year. 1) Jack up the car, put it on jack stands, and remove the front wheels. 2) Remove the two 14mm bolts for the brake caliper. Carefully pull the caliper off the brake pads and set it on something so it doesn’t stress the brake line.
How do you replace the solenoid on a Lexus LS400?
Take the solenoid to your workbench and clean the little screens around the end with a toothbrush and brake cleaning fluid, sparingly mind you, as it is a foreign agent. Replace the solenoid and wires. Put fresh fluid in the reservoir or flush as recommended.
Take the solenoid to your workbench and clean the little screens around the end with a toothbrush and brake cleaning fluid, sparingly mind you, as it is a foreign agent. Replace the solenoid and wires. Put fresh fluid in the reservoir or flush as recommended.
How to fix power steering solenoid on Lexus LS400?
Take a pair of Channel Lock pliers and pull down on the solenoid and it should loosen. Pull down and pull down at least twenty times <_< until the solenoid comes out. A mess will happen and fluid will come out. About a half a quart, Catch it for mother earth.
How do you remove the P / S Pump on a Lexus LS400?
1) Disconnect battery, remove air intake and engine covers . Follow steps 3-10. 2) Loosen the 17mm nut holding the pulley to the P/S pump. Keep the drive belt on while loosening this nut since it will provide some tension. The nut is threaded normally (righty-tighty, lefty-loosey).