How do you remove a water pump from a car?
Use a ratchet or wrench to remove the water pump mounting bolts. Remove the water pump from the vehicle. If the water pump doesn’t come off easily, give it a couple of taps with a dead blow hammer to break it free. Some water pumps are driven off the engine’s drive belt, while others are driven off the timing belt or timing chain.
What’s the best way to replace a water pump?
Use a ratchet or wrench to break loose the water pump pulley retaining bolts (do not remove the bolts at this time). If the pulley starts to spin, you can try putting some extra tension on the belt tensioner to hold it in place. Remove the drive belt by rotating the automatic tensioner.
How do you replace the water pump on a Chevy Silverado?
Loosen the coolant expansion tank cap. Using channel lock pliers, squeeze the tabs on the lower radiator hose spring clamp until the hook locks it open. Then, slide the loose clamp down the hose a few inches. Using a hose pick, carefully work the hose off the water pump nozzle and direct the hose into the drain pan.
What happens if your car water pump goes bad?
When the vehicle is running, the water pump turns, forcing coolant to flow through the engine and radiator. Without the water pump, your car would quickly overheat. Of course, like all auto parts, the water pump can eventually fail. The pump may start to leak, its bearings may go bad, or its impeller may wear away from corrosion.
How do you remove a water pump assembly?
Remove water pump assembly. Remove the alternator bracket bolts and power steering pump bracket from the water pump by turning them counterclockwise with socket and socket wrench. You will also need to remove the bolts and pulley connecting the water pump to the timing chain. Pull out the water pump assembly from the engine block. Figure 5.
How do you get a water pump out of an F150?
Once the bolts are out, you will probably need to use a hammer and a block of wood, or just a hammer to beat the water pump out of the engine. You need to use some common-sense here since the engine is aluminum, but a crisp shot from the left then the right then the left will eventually free the water-pump.
What do you need to replace a water pump?
Scrape off the old gasket from the engine block. Scrape the engine block where the water pump was with a gasket removing scraper to clean the surface. To replace the water pump, spread a gasket sealer on the water pump mounting surface on the water pump back side and on all mounting bolts.
How do you remove a water pump pulley?
Using the break bar, press down or clock-wise, this will loosen the belts from the fan pulley. Finally back out the 4 bolts to remove the pulley. (2 pic below show relieving tension and belt removed.)
Remove the accessory drive belts and the crankshaft damper. Support the engine and remove the right engine mount, the upper left timing belt cover, the upper right timing belt cover and the lower timing belt cover. Then remove the timing belt and tensioner. Remove the water pump from the water inlet pipe.
Where does the coolant go in a water pump?
1. Coolant Leak at the Front-Center of your Car. The water pump is comprised of multiple gaskets and seals that keep coolant contained and ensure that consistent flow of coolant is delivered from the radiator to the engine.
How to replace the water pump in a Chrysler Sebring?
Remove the camshaft sprockets and the cover to the rear timing belt. Loosen and remove the water pump bolts and remove the water pump from the engine. Clean all the mating surfaces and install the new water pump with a new o-ring, making sure that the o-ring is seated correctly in the groove before you tighten the bolts.
How to tell if a car’s water pump needs replacement?
How to Tell if a Car’s Water Pump Needs Replacement. Your car’s water pump is an important part of your vehicle. It is the part that continually pumps coolant to your vehicle’s engine so that it doesn’t overheat.
How often should you replace a car water pump?
Your car’s water pump has a long lifespan but we recommended you replace it at the same time you replace the timing belt. Most vehicles require that the timing belt be replaced at around 100,000 to 150,000 kilometres. Replacing a water pump is difficult and best handled by a professional.
How much does it cost to replace a Honda water pump?
Many Honda owners, however, opt to replace the water pump together with the timing belt because if the water pump fails later it will cost the same labor to replace. Plus, a water pump is not a very expensive part ($45-$170).
Is it a DIY job to replace a water pump?
For most of drivers, replacing a water pump is not a DIY job. Because it is placed deep in the car engine and you can not touch it easily. Almost shops recommend replacing the water pump and making other labor intensive repairs such as swapping out the timing belt in unison. There are some reasons to do that.
With any luck, you shouldn’t have to replace a water pump even if you keep a vehicle for 10 years or more ; they often last that long. Unless a water pump starts to leak, makes unusual noises or quits working, there’s generally no need to replace it.
Do I need to replace my car’s water pump?
It must be inspected during regular services and replaced if it’s bad or shows early signs of failing. In some cases a water pump is replaced as a precaution; for example, when changing the timing belt, or when it’s suspected to cause overheating or in cars that are known for water pump failures. In an average car a water pump lasts for 100,000-150,000 miles, although it can fail prematurely.
How much does it cost to replace a water pump?
Water pumps are in general not very expensive, however the installation can really vary depending on how the pump is driven. Most often your water pump replacement cost will be between $40 and $80 dollars. Exceptions to this price are the electric water pumps which will cost between $150 and $500 depending upon the model of car.
Does your car need a new water pump?
But it is possible to run a motor without one – but highly unlikely. If you plan on keeping your car, then you definitely need to have a new water pump installed, flush out the coolant system, and make sure all the coolant hoses are clean and free of holes.
Put the nut back onto the stud, so you don’t lose it. Remove the alternator retaining bolts, alternator and alternator bracket with the appropriate socket. Remove the water pump pulley bolts, then remove the pulley. Remove the water pump mounting bolts with the appropriate socket, then remove the water pump with from the engine.
Where is the water pump located on a Pontiac?
The Pontiac car is a compact vehicle, so a number of parts and components are installed within close proximity. The water pump on the Pontiac car is connected to the thermostat housing, so you must work with both of these parts to replace the water pump.
How do you remove water pump pulleys on radiator?
Slide the drain pan under the radiator petcock. Open the petcock and allow the antifreeze mixture into the drain pan. Close the petcock. Loosen the water pump pulley bolts, but do not remove them. Loosen the belt tensioners on the accessory drive belts.
How do you remove a water pump from an alternator?
Remove the main power wire from the back of the alternator with the appropriate wrench. Put the nut back onto the stud, so you don’t lose it. Remove the alternator retaining bolts, alternator and alternator bracket with the appropriate socket. Remove the water pump pulley bolts, then remove the pulley.