How do you check Pro RMK codes?

How do you check Pro RMK codes?

Well-known member. With the motor running AND the check engine light on, set the parking brake, then punch the select button on the display. It will then spit out the codes for you right there on the dislpay.

How do I reset my Polaris trouble code?

To reset the ECU, you have to disconnect the battery completely. Then touch your RZR’s wire harness terminals together. This will drain the capacitors and anything else in your ECU that holds a charge, and is a guaranteed method of resetting your Polaris RZR’s check engine light.

How fast does a Polaris RMK 800 go?

Polaris 800 Snowmobile Top Speed Polaris RMK 800 top speed: 105-115 mph.

How do you read a Ski Doo fault code?

You can read the active fault codes on a Ski-Doo by pressing and holding down the M (Mode) button, and at the same time pressing the HI/LOW beam switch a few times. In the worst-case scenario, there is more than one fault code on the display!

How do you reset the check engine light on a slingshot?

To reset the trip odometer, toggle to the trip odometer and then press and hold the MODE button until the trip odometer resets. The error screen displays only when the CHECK ENGINE light is on or when it goes on and off during one ignition cycle.

How do you check the codes on a 2018 Polaris Sportsman 570?

DIAGNOSTIC CODE

1. Press and hold the MODE button to enter the Options Menu. “OPTIONS” will display on the screen for 3 seconds before showing first menu.
2. Select “Diagnostic Codes” from the Options Menu by pressing the MODE. button.
3. To exit the Options Menu the user can select Exit Menu function from.

Is there a problem with my 2013 RMK pro 800?

2013 Pro 800 RMK–seem to have a heating problem–even with 2013 Pro 800 RMK–seem to have a heating problem–even with scratchers down. in hard pack or light snow conditions. Took the back saddle bag and gas tank off and still wants to heat up.

What’s the Det code on a RMK 600 Rush?

According to them it is triggering the det sensor on decel below 3,500′. New to the Rush. Bought a 2010 600 for my son last year. We own 4 RMk 900’s but this is the first rush. He came home today and said he got the de7 (det) code.

Can a 13 800 pro run without code de7?

13 800 Pro with SLP pipe, can, PC V, and SLP’s clutching started throwing code de7 periodically while headed back to the snowpark yesterday. Ran flawless and without this code on numerous long wide open pulls. RPM’s 8,000 to 8,200. Any ideas Polaris guru’s? thru the code while cruising around on trail blipping the throttle?

2013 Pro 800 RMK–seem to have a heating problem–even with 2013 Pro 800 RMK–seem to have a heating problem–even with scratchers down. in hard pack or light snow conditions. Took the back saddle bag and gas tank off and still wants to heat up.

According to them it is triggering the det sensor on decel below 3,500′. New to the Rush. Bought a 2010 600 for my son last year. We own 4 RMk 900’s but this is the first rush. He came home today and said he got the de7 (det) code.

13 800 Pro with SLP pipe, can, PC V, and SLP’s clutching started throwing code de7 periodically while headed back to the snowpark yesterday. Ran flawless and without this code on numerous long wide open pulls. RPM’s 8,000 to 8,200. Any ideas Polaris guru’s? thru the code while cruising around on trail blipping the throttle?

What are the problems with the snowest RMK 800?

The second problem is my speedometer quit working a while back and while i had the secondary off i messed with the wires for the speed sensor and the speedo is working now but its reading at least twice as much as it should.