How do you change the brake pads on a Mercedes C class?
Location of power steering fluid, coolant, brake fluid and windshield washer. Remove the rear wheels from your Mercedes-Benz C-Class (C320, C230, C350). Remove the brake pad wear sensor from the right brake pad. Use a hammer to remove the pin that holds the brake pads in place.
How do you change the brake pads on a W203?
Remove the brake pad wear sensor from the right brake pad. Use a hammer to remove the pin that holds the brake pads in place. As you extract the retaining pin be careful to not hit the brake heat shield. If you hit the shield you may bend it and cause it to make noise when you drive. Use a screwdriver to press the brake cylinder into the caliper.
What should the torque be on a Mercedes brake pad?
The typical torque range is between 30 and 55 Nm and varies between models. Call your dealer to get the recommended torque specifications for your Mercedes-Benz. Connect the brake pad wear sensor.
Location of power steering fluid, coolant, brake fluid and windshield washer. Remove the rear wheels from your Mercedes-Benz C-Class (C320, C230, C350). Remove the brake pad wear sensor from the right brake pad. Use a hammer to remove the pin that holds the brake pads in place.
Remove the brake pad wear sensor from the right brake pad. Use a hammer to remove the pin that holds the brake pads in place. As you extract the retaining pin be careful to not hit the brake heat shield. If you hit the shield you may bend it and cause it to make noise when you drive. Use a screwdriver to press the brake cylinder into the caliper.
The typical torque range is between 30 and 55 Nm and varies between models. Call your dealer to get the recommended torque specifications for your Mercedes-Benz. Connect the brake pad wear sensor.
Where can I buy a Mercedes front brake disc?
Front Brake Disc and Pads : Mercedes & Smart Parts at PartsforMercedes-Benz.com Our range of genuine Mercedes Benz, Mintex replacement, Mintex C-Tech performance, Black Diamond and Tar-Ox performance FRONT brake discs, stop’s your Mercedes the way it was designed to stop.
How do you remove rotors from Mercedes Benz?
If the rotor is stuck, use the mallet to break the rotor free. You will have to tap the middle section of the rotor. Figure 16. Tap the rotor at the circled areas to remove it. Installation is the reverse of the removal. Clean the rotor and caliper by spraying it down with brake cleaner.
How do you replace the caliper on a Mercedes Benz?
Pull the caliper off the caliper bracket, and support it with a hook or wire to avoid hanging it from only the brake line. Then, use a small drill bit to remove two stabilizer pins on the caliper bracket. Insert a flat head screwdriver between the brake pads and the caliper bracket.
How do you remove brake pads from a car?
Then, use a small drill bit to remove two stabilizer pins on the caliper bracket. Insert a flat head screwdriver between the brake pads and the caliper bracket. Twist the screwdriver to push it forward and apply leverage. Then, remove the brake pads.
How do you install a new brake caliper?
Use a screwdriver to press the brake cylinder into the caliper. Remove the old brake pads and clean the area where the brake pads make contact with the caliper. Install the new brake pads. Apply brake grease on the area where the brake makes contact with the caliper. Install the retaining pin.
How do I change the brake pads on my car?
Step by step DIY Instructions on How to change/replace rear brake pads. Set the emergency brakes. Jack up the car using your jack. Place jack stands under the car to secure it. Open the hood and remove the cap from the brake fluid reservoir.
When does brake warning light go off on 2003 C320 mecedes?
High School or GED 19,538 satisfied customers a170 auto: A170 (2003 model ) auto . when starthing and having A170 (2003 model ) auto . when starthing and having foot on brake pedal all warning ligths og off . 3 sec afther removing foot from brake the abs and esp light goes on and remains on until egnition is…
Use a screwdriver to press the brake cylinder into the caliper. Remove the old brake pads and clean the area where the brake pads make contact with the caliper. Install the new brake pads. Apply brake grease on the area where the brake makes contact with the caliper. Install the retaining pin.