Do golf carts have oil filters?
The oil filter is located within a triangular metal housing and is attached to the engine with three bolts. Remove the oil filter’s three retaining bolts with a wrench, then pull the filter out of the engine and allow the oil to drain into the pan. Do not lose the large rubber O-ring that surrounds the filter.
How much oil does a Robins 295 hold?
The oil capacity is 1 1/2 qts.
Can you use synthetic oil in a ezgo golf cart?
Synthetic oil can be used in a golf cart as long as it is the same viscosity. Some manufacturers recommend non synthetic oil only, so make sure to check with your golf carts manual to determine the correct type of oil to use.
What kind of oil do you put in a golf cart?
Most Golf Cars use 10W-30. But if you operate the car at near capacity loads, use 10W-40.
How much oil does a 2006 ezgo take?
The typical engine oil which is used in most of the EZGO carts is 10W-30 and 10W-40. The oil capacity of an EZGO cart is around 6 cups. It is also highly recommended that the engine is checked after a day’s usage to make to the perfect time to change the oil.
What size motor is in a golf cart?
Standard golf car controllers deliver a maximum of 225-275 amps sufficient for golf car applications and flat ground use. If you wish to install a larger 3.5 or 5 hp motor, it’s small size may cause overheating. You can upgrade the 225-275 controller without them overheating.
What kind of oil should I use on a Robin 295?
The oil to use for a Robin 295 engine should be a grade of 10w 30 or 10w 40. I have also used Mobil 1 in my Robin engine, and it worked fine. The grade of the oil should meet CC, SG, or SF for a smooth run. I always clean the oil filter after running the engine for 125 hours and even sometimes change them.
What kind of engine does a Robin golf cart have?
Robins Engine 1996-2002 . . . . Nivel EZ GO Golf CART Engine Rebuild KIT & GASKETS 295CC Robins Engine 1996-2002 with .25MM OS Piston. Lower 48 US States! . . . . . Only 9 left in stock – order soon.
Why is my Robin 295 engine not starting?
The robin 295 engine timing is an integral part of starting the engine. Multiple pulleys are attached with the timing belt. As soon as the engine is cranked, the pulleys rotate as they are fixed with the timing belt. Sometimes, the belts jump-off and the engine is unable to start.
What should the compression be on a Robin 295?
The ideal Robin 295 robin engine compression should be around 120 to 150 PSI or sometimes slightly higher. Many times it happens that the compression drops to 70, 80, or even less psi.
The oil to use for a Robin 295 engine should be a grade of 10w 30 or 10w 40. I have also used Mobil 1 in my Robin engine, and it worked fine. The grade of the oil should meet CC, SG, or SF for a smooth run. I always clean the oil filter after running the engine for 125 hours and even sometimes change them.
Where can I buy a 295cc Robin engine?
BUY with confidence from the #1 Small engine builder.295 cc 2-cylinder “Pre-MCI” Robin Engine by Fuji Heavy Ind. Fits years 91-02 (confirm your model). Engine model number is stamped on base of crankcase on exhaust side.
Robins Engine 1996-2002 . . . . Nivel EZ GO Golf CART Engine Rebuild KIT & GASKETS 295CC Robins Engine 1996-2002 with .25MM OS Piston. Lower 48 US States! . . . . . Only 9 left in stock – order soon.
The ideal Robin 295 robin engine compression should be around 120 to 150 PSI or sometimes slightly higher. Many times it happens that the compression drops to 70, 80, or even less psi.