Can you change the brake pads on a Kia Spectra?
Changing the brake pads on a KIA Spectra is not hard, but you will have to be somewhat mechanically inclined. The entire task takes less than an hour and doing it yourself can save you some cash. Park the vehicle on level ground and apply the parking brake.
What do I need to replace my brake pads?
Compress the caliper piston into the bore using tool number OK9A4263001. Replace the brake pads. Use an anti-squeak product on the outside of the brake pads. Be sure not to get any of this on the inside of the brake pads.
What is the tool number on a Kia?
Kia recommends using tool number OK9A4263001, which might be difficult to find in your local auto parts store. However, you can use a universal brake caliper rewind tool, and some home mechanics have found that a good pair of needle-nose pliers work just fine. It is important not to damage the piston boot to avoid expensive repairs.
How do you install a new brake caliper?
Rotate the brake caliper piston slowly using a brake-caliper rewind tool to seat the piston into its bore, making sure to align the piston cutout with the tab on the back of the new inner-brake pad. Install the plate wear indicator, new inner brake pad, new outer brake pad and shim on the caliper bracket.
Changing the brake pads on a KIA Spectra is not hard, but you will have to be somewhat mechanically inclined. The entire task takes less than an hour and doing it yourself can save you some cash. Park the vehicle on level ground and apply the parking brake.
What are the brake calipers on a Kia Rio?
Brake calipers stick making brakes and wheel hot. Put new calipers and pads on. Did the same again, so replaced flex Kia Rio: Brake calipers stick making brakes and wheel hot. ASE Certified Technician/A… The brake pads are sticking to the rotors turning cherry red..
How to replace the brake pads on a car?
Replace the brake pads on the opposite brake assembly as described above, beginning with Step 6 of the previous section. Install both rear wheels and lug nuts. Lower the vehicle using the floor jack and finish tightening the lug nuts. Add new brake fluid to the reservoir on the brake master cylinder to bring the level to the “Full” mark.
How do you remove brake hose from Kia?
Detach the clip holding the caliper brake hose to the suspension arm using a pair of nose pliers, if your Kia model is equipped with it. Unscrew and remove the upper and lower caliper guide bolts using a ratchet and a hex socket.
How do you change the brake pads on a Kia Spectra?
Depress fully the brake pedal five times to seat the new brake pads on the brake rotor. Road-test your Kia on a lightly used road to make sure the brakes are working properly. Drive to a highway with few cars, slow the vehicle from 60 mph to 10 mph and repeat eight times without stopping.
Replace the brake pads on the opposite brake assembly as described above, beginning with Step 6 of the previous section. Install both rear wheels and lug nuts. Lower the vehicle using the floor jack and finish tightening the lug nuts. Add new brake fluid to the reservoir on the brake master cylinder to bring the level to the “Full” mark.
Detach the clip holding the caliper brake hose to the suspension arm using a pair of nose pliers, if your Kia model is equipped with it. Unscrew and remove the upper and lower caliper guide bolts using a ratchet and a hex socket.
How do you replace the brake pads on a car?
Remove the brake pads and retainer spring from the caliper. Compress the caliper piston into the bore using tool number OK9A4263001. Replace the brake pads. Use an anti-squeak product on the outside of the brake pads. Be sure not to get any of this on the inside of the brake pads.
How to replace front brake pads Hyundai years 2008?
(Playback ID: 8hl-t_DRtoSDQLDC) An error occurred while retrieving sharing information. Please try again later.
Remove the brake pads and retainer spring from the caliper. Compress the caliper piston into the bore using tool number OK9A4263001. Replace the brake pads. Use an anti-squeak product on the outside of the brake pads. Be sure not to get any of this on the inside of the brake pads.
(Playback ID: 8hl-t_DRtoSDQLDC) An error occurred while retrieving sharing information. Please try again later.
Rotate the brake caliper piston slowly using a brake-caliper rewind tool to seat the piston into its bore, making sure to align the piston cutout with the tab on the back of the new inner-brake pad. Install the plate wear indicator, new inner brake pad, new outer brake pad and shim on the caliper bracket.