Are there any problems with the Harley Davidson clutch?
This recall involved problems with the clutch system which won’t fully disengage. In the report, Harley-Davidson said this is the result of gas bubbles in the master cylinder clutch. If you’re considering these models, check with the dealer to make sure that the clutch got flushed or the master cylinder got rebuilt.
How to adjust the clutch cable on a Harley Davidson?
In this video I show you how to adjust the clutch cable on a 2009 Harley Davidson Softail Custom. The proper free play between the end of the clutch cable or cable Ferrule and the clutch lever housing is 1/16″ to 1/8″. Thanks for Watching! Loading…
What should I do if my Clutch goes bad?
Replace steel plates if blue’d or warped. A glass top coffee table works great for checking them,. as does a framed picture. If you replace the clutch plates (fibers) soak in XYZ primary oil before installing for at least an hour. I used our wedding picture to do that once. Wife was pissed. So sensative…….
What are the most common problems with a Harley Davidson?
Fuel System Failures Vapor lock malfunctions, fuel injectors, and defective pressure gauges are among the most reported problems with a Harley’s fuel system. These problems can be costly and difficult to repair. Complete regular maintenance checks on the fuel system to guarantee that it’s running properly. 6. Accessories
This recall involved problems with the clutch system which won’t fully disengage. In the report, Harley-Davidson said this is the result of gas bubbles in the master cylinder clutch. If you’re considering these models, check with the dealer to make sure that the clutch got flushed or the master cylinder got rebuilt.
How do you adjust the clutch on a Softail Harley?
Bob teaches you how to adjust the clutch and primary chain on your Harley Softail or Dyna model. Be sure to achieve free play on the clutch cable to verify that you have proper adjustment on the clutch cable pack, and check for the proper specs in your service manual for adjusting the primary chain (if your model has the adjustment window).
How do you close the clutch on a Harley?
End of dialog window. This is a modal window. This modal can be closed by pressing the Escape key or activating the close button. This is a modal window. This modal can be closed by pressing the Escape key or activating the close button. Bob teaches you how to adjust the clutch and primary chain on your Harley Softail or Dyna model.
Replace steel plates if blue’d or warped. A glass top coffee table works great for checking them,. as does a framed picture. If you replace the clutch plates (fibers) soak in XYZ primary oil before installing for at least an hour. I used our wedding picture to do that once. Wife was pissed. So sensative…….
Where is the clutch release cover on a Harley 5 speed?
Harley hasn’t changed this procedure since the arrival of the 5 speed with the clutch release cover on the right side of the tranny in around 1984. it is only different if a hydraulic clutch actuator has been installed. try it one more time. – slack the clutch cable fully. ensure the clutch lever will rest on the left hand grip.
What should I do if my Clutch is slipping?
When you get out on the road get rolling slowly (about 25 mph in 3rd gear) then briskly roll on the throttle. If the motor bogs a bit before cleanly accelerating you are good. If the motor revs faster than the bike accelerates then the clutch is slipping and a readjustment is in order.
How to adjust the clutch on a Heritage Softail?
– slack the clutch cable fully. ensure the clutch lever will rest on the left hand grip. – screw the clutch adjusting screw in……but continue screwing it in until you feel the clutch release. this ensure all clutch release components are fully seated.
Harley hasn’t changed this procedure since the arrival of the 5 speed with the clutch release cover on the right side of the tranny in around 1984. it is only different if a hydraulic clutch actuator has been installed. try it one more time. – slack the clutch cable fully. ensure the clutch lever will rest on the left hand grip.
– slack the clutch cable fully. ensure the clutch lever will rest on the left hand grip. – screw the clutch adjusting screw in……but continue screwing it in until you feel the clutch release. this ensure all clutch release components are fully seated.
What does it mean when a Harley won’t idle?
Went to start it won’t stay idling unless you either hold the choke out or give it some throttle. Also when you ride their is like a hesitation where the bike kind of jerks like it loses fuel supply forms split second any recommendations. Click to expand…
What causes a Harley Davidson not to start?
Some other ideas: 1 Problem with security module or key FOB 2 Problem with clutch safety switch, or its wiring (if bike has it) 3 Bad relay (like you said)
Are there any recalls on Harley Davidson motorcycles?
In the report, Harley-Davidson said this is the result of gas bubbles in the master cylinder clutch. If you’re considering these models, check with the dealer to make sure that the clutch got flushed or the master cylinder got rebuilt. This recall affected 46,000 Harley-Davidson motorcycles in total.
Why does my bike not start with the clutch pulled?
Won’t start in gear WITH clutch pulled. Does anyone have an idea why I can only start my bike if it’s in neutral? A few days ago I was at a stop light and went to slip into neutral to idle while at the red light, but it wasn’t neutral, IT WAS FIRST, so when I let go of the clutch the bike lurched and stalled.
What happens when you let go of the clutch on a Harley Davidson?
A few days ago I was at a stop light and went to slip into neutral to idle while at the red light, but it wasn’t neutral, IT WAS FIRST, so when I let go of the clutch the bike lurched and stalled. Oh, and I can drop my jiffy-stand while idling and the engine won’t cut off.
Why does my Harley Davidson not start in gear?
Inside the clutch handle assembly there is a button that when depressed by the clutch handle should allow the engine to start IN GEAR. Right? But for all this to work both the clutch handle assembly and switch housing have to be fitted against each other tightly or the clutch lever cam won’t depress the button far enough to work.
What happens when the Idle is high on a Harley Davidson?
Strange that there are no historical codes since you did say you saw the check engine light come on. (Could be you went through 50 key cycles with no engine issues) When you get off the interstate & the idle is high,,, if you were to power it off and restart the bike, does the idle calm down or does it resume the high idle.