Are there any problems with my Mercedes ML 320?

Low range light flashing. Power steering problems. Will need power steering pump replacement. Door lock actuators also tend to be prone to failure. Plastic trim inside the car break easily. Window regulator. Fuel pump. Oxygen sensors. Alternator may need replacement between 130k and 170k miles.

Is the Mercedes-Benz ML400 a good truck?

The later models had less problems compared to the first few years of production, specifically the 1998 and 1999 model years. Another thing to keep in mind is that Mercedes-Benz ML, especially ML430 and ML500 are great truck for towing. Picture M-Class, W163. If playback doesn’t begin shortly, try restarting your device.

What kind of gearbox does the Mercedes ML have?

The 722.6 gearbox installed in the ML is one of the most reliable transmission produced. ABS/ETS/ESP lights. Needs replacement of ABS pump. Easy DIY, follow these instructions. Transmission O-ring. Follow these DIY instructions if you need to repair yours. Transmission stuck in gear, limp mode. Learn how to troubleshoot transmission limp mode.

What causes rust on a Mercedes-Benz 2000?

I have a 2000 and don’t have a spec of rust – anywhere. Rust will form if you have a chip down to the metal and you don’t touch it up. Anti-corrosion methods are excellent in a Benz – its not water/vs solvent based paint that is an issue its the way a car is maintained. The car is dipped in a zinc base which seals out the rust.

Is the Mercedes-Benz E320 immune to rust?

In that sense I feel that Mercedes usually has an advantage over BMW but maybe for the 1998-2003 era it is the other way around. My 1995 E320 is not immune to rust either even though it is always garaged, just recently there is a new rust bubble on the edge of the hood.

When did the rust start on the Mercedes W124?

I love the W124, would just like a little sportier ride. Regarding the much talked about corrosion problems, I have read in a few sources that the rust problems supposedly only started in mid 1999 when Mercedes switched to water-based paint and that 1998 MY should be relatively corrosion-free. Any truth to that from your experience?

Is there rust on my Mercedes Benz CLK430?

No rust anywhere on my 2000 CLK430 – except in one spot on the lower corner of the door where I touched some concrete and it left a chip. The car never is driven in the winter on salty roads and I wash and dry it by hand all the time.

What are the problems with a Mercedes Benz?

Top 5 Mercedes-Benz no start problems 1 Engine Click, No Start 2 Engine Dies Right After It Starts 3 Car turns over, but it won’t start 4 The car makes a clicking noise but won’t start. Hint: Starter Problem or Low Battery 5 Key will not turn the ignition More …

What causes a Mercedes-Benz ML320 to stall?

Tap the to learn more about the most common Mercedes-Benz ML320 problems. The engine may stall when the engine is warmed up. The AC compressor may seize resulting in loss of cold air from the AC vents. There have been some issues reported with the electric sliding doors. Ignition switch failure may cause the car to stall or fail to start.

Are there any problems with the Mercedes ML?

Mercedes-Benz improved some designs and address several of the problems on the list above. The later models had less problems compared to the first few years of production, specifically the 1998 and 1999 model years. Another thing to keep in mind is that Mercedes-Benz ML, especially ML430 and ML500 are great truck for towing.

What kind of engine does the Mercedes ML320 have?

MLs share the M112 engine found in the ML320 and the M113 engine found on the ML430, ML350, ML500. The 722.6 gearbox installed in the ML is one of the most reliable transmission produced. ABS/ETS/ESP lights.

What are the symptoms of a bad fuel pump?

The engine may still crank when the key is turned, however it will not be able to start due to lack of fuel. This symptom can also be caused by a wide variety of other issues, so having the vehicle properly diagnosed is highly recommended. 3. No noise from the fuel pump

When does the engine stall in a Mercedes?

There are never any notifications on the dash or any signs of it beginning to fail. This typically happens when I’m slowing down at an intersection or just driving slower in traffic.

What’s the fuel pressure on a Mercedes Benz?

A great and affordable gauge that we have used in the past is this Actron Fuel Pressure Gauge which works on Mercedes-Benz cars. Turn the engine off and connect this gauge to the Schrader valve test port shown in the picture below. Start the car and you should be able to get around 60 psi.

What should I do if my Mercedes Benz won’t start?

Start the car and you should be able to get around 60 psi. When the engine is running and when you turn off the engine the pressure should stay steady. Always perform this test on a cold engine. Next, make sure that the fuel injector connections are secure and not loose. Check the fuel pump and the fuel pump relay.

Can you erase a fault code on a Mercedes Benz?

Can clear fault codes. Can read and erase all fault codes on Mercedes-Benz cars. Only works on MB but can perform further troubleshooting including SBC brake systems, convertible systems, Air Conditioner (A/C) system. 3. Mercedes-Benz Star Diagnostic DAS This is diagnostic scanner used at Mercedes-Benz dealerships.

Why is the battery on my Mercedes Benz not working?

Hint: Starter Problem or Low Battery This may seem obvious, but an old battery is the root of many headaches and can cause all sorts of malfunctions on Mercedes-Benz cars. How old is the battery on your Mercedes-Benz?

How to check check engine light on Mercedes medic?

If you want to do more research then use Search function on Mercedes Medic or any other search engine to get a better idea of the problem. On any search engine enter the manufacturer and the code you got from the scanner. For example: Mercedes-Benz P0300

When does the engine management warning light appear?

Engine Management Warning Light (Diesel Engines Only) If the light appears when the ignition is switched on, this is a normal function (to appear for a few seconds). If the light appears whilst the engine is running drive slowly and carefullyto an authorised repairer immediatelydue to engine management fault.

What do you need to know about Mercedes warning lights?

M-Class S-Class SL SLC SLK V-Class AMG Range Mercedes-Benz Ex-Demo New cars available now Value My Mercedes-Benz Offers New Car Offers Used Car Offers Servicing & Parts Offers Business Offers Motability Offers Service & Parts Book a Service Book an MOT ServiceCare Plan Why Service with Us? Vehicle Health Checks Complimentary Roadside Assistance

When did the Mercedes Benz W163 come out?

The Mercedes-Benz ML-Class (W163) built from 1998 to 2005 has a reputation for not being a reliable car. At the same time there are many owners who have put over 200k or even over 300k miles on this SUV.

When did the Mercedes Benz ml500 come out?

The ML430 was replaced at this stage by the ML500, a 292bhp monster designed to spike the guns of BMW’s X5. An all new M-Class hit the streets in 2005. In short, a massive hunk of metal.

Why do my Mercedes Benz ESP Lights Come On?

The BAS / ESP / ABS lights is not a problem with just Mercedes-Benz ML320 / ML430 models. It is a problem that has impacted all Mercedes-Benz models. We have included the top causes that trigger these lights to come on in the section below.

Where is Bank 1 sensor 1 in my ML320 3?

Hi, bank 1 sensor 1 is located on the passenger side and is the front oxygen sensor. It will be in front of the catalytic converter.

Why does my ml 350 blue TEC not start?

ML 350 Blue Tec The car doesnt start or there is a long delay when I turn the key . Intermittent and getting worse. I put the key in the ignition and there is a delay in the ignition and at times no ignition at all. Wont start when I turn they key. try again and sometimes it will start. seems to be getting worse.

Why does my 2010 Mercedes ML350 not start?

Knauz Mercedes kept the car for a week and could find no fault. I am having trouble with my 2010 ML350. sometimes when I turn on the ignition, the electronics do not turn on, and the car will not start when engaged. if I turn the key off and try again it may or may not work, but it will work after a few tries.

What causes a Mercedes Benz to not start?

In most cases you will get a fault code related to one of the following: 1 ECM / PCM computer failure 2 Camshaft position sensor 3 Shifter Selector module 4 Fault codes related to driver authorization or immobilizer 5 Electrical problems

Why do I get message start error on my Mercedes Benz?

Got message Start Error. It was coming on from time to time but now is on. Both keys are not starting. Batteries in car and keys are OK. Ignition switch seems to be all clean and functional. AAM looks pristine inside. Probably immobilizer. Can not get to a garage more then 100 ml away.

What to do if your Mercedes won’t start?

How to Fix Mercedes Start Error? Why my Mercedes Won’t Start? If playback doesn’t begin shortly, try restarting your device. Videos you watch may be added to the TV’s watch history and influence TV recommendations. To avoid this, cancel and sign in to YouTube on your computer. An error occurred while retrieving sharing information.

What causes start error on Mercedes Benz immobilizer?

While 43sqd is right about “start error” being frequently caused by faulty DAS module, for a previously intermittent “start error” issue you would have to consider a faulty DAS transponder ring as shown in this MB diagnostic algorithm. The DAS ring is not coded – it’s just a piece of wire.

What kind of car has a start error?

Ml 270 Cdi 2002. Got message Start Error. It was coming on from time to time but now is on. Both keys are not starting. Batteries in car and keys are OK. Ignition switch seems to be all clean and functional.

What is the recirculated air button on a Mercedes?

This is as far as the cylinder will go without cranking the engine. Press and hold the defrost and recirculated air buttons simultaneously. The defrost button has three lines going through it, while the recirculated air button has a picture of a car with a curved line through it.

Why does my Mercedes E320 AC not reset?

For example, if you want to know about Mercedes E320 AC reset, it is better to check the manual and follow the manufacturer’s recommendations. If a Mercedes air condition reset does not work, these following reasons could be causing the trouble: When the AC is releasing hot air, the possible reason could be a defect in the damper.

How much is a 1999 Mercedes Benz ML 320 worth?

Year200320022001200019991998Year See Trade-in Value Used 1999 Mercedes-Benz M-Class ML 320 Sport Utility 4D Edit OptionsMileage: 157,858 4.1 Consumer Write a review View Gallery For Sale 28 Mercedes-Benz M-Class vehicles nationwide. Used 2000 Mercedes-Benz ML 320 4MATIC New Listing $2,995 Regan Motors Used 2000 Mercedes-Benz ML 430 4MATIC $3,990

Can a pre 2000 ml lose its settings?

On the early pre 2000 ml’s the aam can loose it’s settings when disconnected from the battery. These can include the ignition key sync or even the keys rfid information. If when you try to start it starts then run some for maybe a half second before shutting down this could be your problem.

Why does my ML not start while driving?

One might be the cause of the battery drain or not starting then your ML may have lost the key information. If it wouldn’t start or it stop while driving but after say 30 minutes it would start and run normally then it might be your crank shaft position sensor. $50 sensor back of engine drivers side about 10 minutes to diy fix.

What happens if you turn off the Aam on a 2000 ml?

STARTS UP SHUTS DOWN BATTERY WENT DEAD CHANGE IT NOW IT WONT STAY RUNNING. It will if u keep it running for 10 minutes.. On the early pre 2000 ml’s the aam can loose it’s settings when disconnected from the battery. These can include the ignition key sync or even the keys rfid information.

Why is my ignition not working on my Mercedes Benz?

It is possible that the battery in the car is defective, as it does not provide the necessary voltage for the ECU and the N73 Electronic Ignition/Starter Switch (EIS) to function properly. If the battery is dead or has low voltage / under voltage, the CAN communication between EIS and N72 may not function properly.

Why does the key not turn when inserted in the ignition?

The EIS module could also be the reason that the key does not turn when inserted in the ignition. Many car owners complain that the car starts fine on a warm or hot day but in cold days the car will not start. This may sound strange, but it is reported frequently.

Why does the engine cooling fan not turn off?

I was wondering if anyone knows why the engine cooling fan does not go off when you turn engine off. We had to pull the fuse that is under hood on top of battery. Once we pulled it, it went off, but when we put it back in the fan started up again. Any and all replies would be greatly appreciated. 50 people found this helpful.

Can a VW Jetta fan run after the engine is shut off?

Definitely hold on to the info. The fan can run after the engine shuts off, but I’ve read about failures where the fan keeps running until the battery is dead. A sticking relay or switch, can jar itself loose while driving. But if it sticks once, it will likely do it again.

How long does a Mercedes Benz blower fan run?

Pressed the switch again, the blower fan stopped again for a few seconds, then resumed the lower speed. The owner’s manual notes the fan may run for up to 30 minutes in warmer temperatures. Left it for an hour – still running at the low speed.

Why does my car fan keep running when the car is turned off?

Look in your owners manual. I think it’s primarily for cold weather, it keeps the car interior warm until the heater core completely cools down. Not to say you don’t still have a problem separate from that. It keeps running for hours unless I unplugged the battery or the motor itself. That is the design.

Why is my Furnace Fan running at a reduced speed?

A bad fan motor running at a reduced speed because it will soon fail. In this case, the fan motor needs replacing. As you can see, these problems are furnace control issues. Some involve safety controls as a furnace can be dangerous if not controlled properly.

What to do if your Mercedes Benz fan is stuck?

Not hard to do, just drop the blower motor and replace the regulator. The hardest part is positioning your self under the dash and looking upwards to locate the mounting screws. Hi Paul, just wondering if you found a solution to your stuck fan.

Is there a radio code for the Mercedes ML320?

Yes it’s final time for solving your Mercedes ML320 radio code problem. Bring back to your motivating drive while you listen real music on your disc or maybe on your favorite radio station. Solve the problem that make you unhappy while you traveling around your country or maybe around the world.

Can a person fix a Mercedes Benz ML320?

Mercedes Benz ML320 AC Fix and Repair ANYONE can do it! – YouTube Mercedes Benz ML320 AC Fix and Repair ANYONE can do it! If playback doesn’t begin shortly, try restarting your device.

Is the Mercedes Benz ML320 ml430 ml500 ETS ABS?

BAS ESP ETS ABS Mercedes Benz ML320 ML430 ML500 FIX!!! An error occurred while retrieving sharing information. Please try again later.

Is there an iOS file on the catalyst 9200?

09-17-2019 08:56 PM I have factory reset the Catalyst 9200 and now I don’t have IOS file there. I know it sounds dumb but can someone help me to install the IOS file there again?

What should I do if my catalyst monitor stops running?

The first and foremost step is to check whether the engine light is off. If your vehicle has active trouble codes, it may stop a monitor from running completely. 2. Check if your Vehicle has a Coolant Temperature

What happens if you remove the catalytic converter on a ml500?

FYI, the ML500 is an LEV with four cats, and gets 20mpg. 22 highway. The ML engine is tuned by computer to run with a certain amount of back pressure. If you remove those converters, it will screw up the way the engine runs because there’s no way the computer can compensate for the absence of back pressure. In other words, don’t do it.

Can a bad catalytic converter lead to engine failure?

A bad or clogged catalytic converter can ultimately lead to engine failure, so it’s important to address the issue promptly. However, having catalytic converter problems doesn’t necessarily mean that the converter has to be replaced.

Can a lazy oxygen sensor cause a catalytic converter problem?

You may need to fix other engine problems in order to solve your catalytic converter problem. A lazy oxygen sensor might falsely indicate a catalytic converter problem, yet not set a DTC for itself. A technician can determine if the sensor is responding as it should.

How to troubleshoot catalyst monitor not ready issue?

Now, switch the rear defroster and ac off and keep the speed of your vehicle at 90 km/hr (55MPH) nearly for 3 minutes. During this period, the purge and Fuel monitor diagnostics will take place. 5. Decelerate your Vehicle’s Speed at 20 MPH Make the speed of your vehicle fall gradually up to 32 km/hr (20 MPH).

Why is the ESP light on on my 2002 ML320?

ESP/BAS is on since I had some work done on my 2002 ML320.The battery had to be disconnected at the time,but now the light won’t go out.Why? My break light switch has failed twice. Once causing the break lights to stay on continually and BAS/ESP light to illuminate.

What kind of engine does the ML320 have?

Overview Overview ML320 AWD 4dr SUV 3.2L 6cyl 5A ML55 AMG Engine Type Gas Transmission 5-speed shiftable automatic Drive Type All wheel drive Cylinders V6

Are there any problems with the Mercedes-Benz W163?

At the same time there are many owners who have put over 200k or even over 300k miles on this SUV. Problems such as door lock actuators or plastic trim that brakes easily are issues that disappoint owners. We have worked on and owned several W163 and have put together the list of common problems for you.

How do you reset the key fob on a Mercedes ML320?

Press and hold the “LOCK” button on the key fob. Remove the key from the ignition. Keep the “LOCK” button held down while removing it. Press and release the “UNLOCK” button five times. Release the “LOCK” button. The fob is reset. “2010 Mercedes ML320 Owners Manual”; Mercedes-Benz USA; 2009

What are the most common problems with Mercedes Benz cars?

8 Most Common Mercedes-Benz Problems 1 Rust. Rust behind license plate / trunk area. 2 Engine Mounts. Engine mounts on Mercedes-Benz cars are oil filled. 3 Suspension & Steering Components. Ball joint / front control arm. 4 Window Regulators. Broken window regulator on Mercedes C-Class. 5 AirMatic Components. …

What are the most common problems with Mercedes Benz ML320?

The number one most common problem is related to the vehicle’s steering (148 problems). The second most common problem is related to the vehicle’s service brakes, hydraulic (133 problems). Table 2. Common problems of Mercedes Benz ML320

How to check transmission fluid in a ML320 Benz?

On many cars, checking the transmission fluid level is a two-minute process just like checking the engine oil level. But with the Mercedes Benz ML320, there’s an important extra step. The ML320 is designed to require no maintenance, so it doesn’t ship with a dipstick as standard equipment.

Why is the fuel gauge empty on my 2001 ML320?

MY 2001 ML320 exhibited the fuel gauge problem today. I filled fuel this morning on my way to work. Soon thereafter, the fuel gauge showed that it was empty despite a complete fillup.

Where is the flap on the ML320 ml430?

Open the glove box and you will see the four screws that hold it in place. Once you remove the screws pull out the glove box. Behind the glove box (on the left) you will see a white plastic arm. This is the flap that switches the air flow from hot to cold. It gets stuck in HOT position.

Why is my ML320 blowing hot air only?

A common problem with the ML320 / ML430 is the AC getting stuck on Hot or Cold setting. This is caused by the blend motor flap getting stuck and no longer moving when you rotate the AC knob between Hot and Cold. You can manually switch the blend motor flap if you remove the glove box.

How long does a Mercedes Drive Cycle take?

Lambda (02) Sensor Signal (do not interrupt this portion of the test, to be conducted directly after • Drive vehicle for 3 minutes at 70km/h (43 mph). • After the 3 minutes has been reached proceed to step 3 below.

Can a 2002 Mercedes Benz drive cycle be incomplete?

Also, one customer with a 2002 Mercedes was unable to complete the secondary air injection monitor until one evening he allowed his vehicle to idle for 5-20 minutes in his driveway. He then turned off his vehicle and restarted the vehicle the next morning and allowed it to idle for another 5-10 minutes.

How to troubleshoot a Mercedes Benz fuel pump problem?

Troubleshooting a bad fuel pump problem on a Mercedes-Benz is easy. This is a job where you need to be extremely careful because you will work near fuel and there is always the risk of fire. It is recommended that you empty the tank or have the fuel tank near empty when you replace the fuel pump.

What should I do if my Mercedes fuel pressure is zero?

If your Mercedes doesn’t start, check the fuel pressure. If you are getting zero reading, you either have an electrical problem or a bad fuel pump. If the check engine light is on, consider yourself “lucky” as it can make your diagnosis easier. Note that not all faults will trigger the check engine light.

How much does it cost to replace a Mercedes fuel pump?

Don’t be surprised if your Mercedes goes into limp mode for fuel related problems. Use Star Diagnostic scanner to perform a complete system scan. To replace the fuel pump on a Mercedes-Benz, it costs between $450 and $800 depending on the MB model. You will pay about $300-$450 for parts (fuel pump) at the dealer.

Why is my electric seat not working in my Mercedes?

If its is CLK320 2002, then is it the fuse no 6. white 25 fuse. Otherwise please check the list in the fuse box, it will tell you which one is for seat adjustment. yep my passenger seat has the same problem. i can still hear a clicking sound when i press the backward and forward button though…. like its stuck…

Why is my electric seat not working on my CLK 320?

My CLK 320 electric seat on the driver side is not functioning, the forward and backward movement is not working but the back rest and the head rest works perfectly. Can someone advice how i can shift my seat backward to the position i preferred for driving?

When did the Mercedes Benz ML Class come out?

In this article, we consider the first-generation Mercedes-Benz M-Class / ML-Class (W163), produced from 1997 to 2005.

How to change the seat position in a Mercedes?

Move the seat all the way to the back. When the seat reaches the furthest back position continue to hold the switch for minimum of 3 seconds. You can follow the same procedure to adjust any of the seat positions, the head rest and the steering wheel column.

How many seats does a Mercedes Benz have?

You can program up to two seat settings in your driver’s seat in a Mercedes-Benz vehicle. Get into your Mercedes-Benz, close the door and turn on your vehicle. Locate the seat adjustment knobs on the driver’s seat of your Mercedes-Benz.

In this article, we consider the first-generation Mercedes-Benz M-Class / ML-Class (W163), produced from 1997 to 2005.

What causes seat synchronization issue in Mercedes Benz CLK?

This happens because the Electric Seat Adjustment (ESA) control modules (N32/1 left or N32/2 right) which are responsible for controlling the seat no longer remember the limits where the seat can extend. To resolve this problem, we will need to re-synchronise the seats which you can do in a couple of minutes.

Are there any Mercedes Benz models that have bas lights?

What’s the name of the Mercedes Benz parking light?

Parking light. P21/5W. Front turn signal. P21/5W. Rear turn signal. P21W. Tail light. 5007 or 12821 or R5W. Tail light.

When did the Mercedes-Benz ML 320 come out?

No accident or damage reported to CARFAX… 1st owner purchased on 10/11/07 and owne… Last serviced at 174,104 miles in Frankl… 1st owner drove an estimated 16,238 mile… No accident or damage reported to CARFAX…

What are the different types of Mercedes Benz light bulbs?

Mercedes Benz Light Bulb Look Up Sizes and Types 1 B-CLASS 2 C-CLASS 3 CL-CLASS 4 CLA-Class 5 CLK-CLASS 6 CLS-CLASS 7 E-CLASS 8 G-CLASS 9 GL-CLASS 10 GLA-Class

Parking light. P21/5W. Front turn signal. P21/5W. Rear turn signal. P21W. Tail light. 5007 or 12821 or R5W. Tail light.

What are the diagnostic codes for Mercedes Benz?

Mercedes-Benz Diagnostic Trouble Codes (DTC) for 1996+ models Powertrain P0100 Mass or Volume Air Flow Circuit Malfunction P0101 Mass or Volume Air Flow Circuit Range/Performance Problem P0102 Mass or Volume Air Flow Circuit Low Input P0103 Mass or Volume Air Flow Circuit High Input P0104 Mass or Volume Air Flow Circuit Intermittent

What does CL stand for in Mercedes Benz?

Mercedes-Benz models such as the Mercedes-Benz CLS and Mercedes-Benz CLA have the letters CL added on. The CL means that the vehicle is a 4-door coupe, and therefore only applies to the four-door coupes of the Mercedes-Benz lineup.

What are all the codes on a Mercedes Benz?

Use an advanced OBD-II code reader to read and erase Engine CEL, Transmission, ETS, ABS, Airbag and other systems. There are also codes for other control units such as transmission, ABS, SRS, ESP, 4ETS, airbag, A/C. Mercedes-Benz can have up to 47 control units. You can NOT diagnose them with a simple OBD-2 scanner.

How many control units does a Mercedes Benz have?

There are also codes for other control units such as transmission, ABS, SRS, ESP, 4ETS, airbag, A/C. Mercedes-Benz can have up to 47 control units. You can NOT diagnose them with a simple OBD-2 scanner. To read these systems and their fault codes or erase them from your Mercedes-Benz you need more advanced OBD-II scanners.

Which is the best OBD code reader for Mercedes Benz?

Top 3 OBD-2 code readers for Mercedes-Benz have been listed under the green column below. 1. OBD II Code Reading Scanners – For ECU Only 2. BlueDriver Scan Tool for iPhone and Android

What’s the fault code for a 2001 Mercedes Benz?

Click to expand… For the ML class it does not apply to the 2001 models. Also the fault code in the bulletin is for DTC B9103 and DTC B9123. No others would be covered by the DTB. Post # 34 in this thread lists the DTB the parts, and all affected models.

What causes a Mercedes Benz steering angle sensor to lose memory?

B1628 Part E2e5 (Turn signal lamp) in module E2 (Right front headlamp unit) is defective. Body C1140 BAS light, play in steering column causes steering angle sensor to lose memory (?) Chassis C1504 BAS light, play in steering column causes steering angle sensor to lose memory (?) Chassis P0818 Driveline Disconn. Switch Input Circuit Malfunction

Can you read the fault code on a Mercedes Benz?

Can read fault codes from multiple systems such as transmission, engine, ETS, airbag and more. Can clear fault codes. Can read and erase all fault codes on Mercedes-Benz cars. Only works on MB but can perform further troubleshooting including SBC brake systems, convertible systems, Air Conditioner (A/C) system. 3. Mercedes-Benz Star Diagnostic DAS

What is fault code b1859 on Mercedes Benz?

There is a known issue with poor connection in the lines to the steering column module that connect to the airbag for fault code B1859. There is a repair that involves repairing the wiring in the loom to this module as the SRS control module sees too high a resistance to the drivers airbag.

When did the Mercedes ML Class come out?

Enjoy! The Mercedes-Benz M-Class (or ML-Class) is a mid-size luxury sport utility vehicle (SUV), introduced in 1997 as a 1998 model, and built by the German automaker Mercedes-Benz. Gradually, the M-Class became a sales success in the United States and Mexico. ML 320 is a five-door sport utility vehicle manufactured from 1998 until 2001.

Where is the UHI connector on a Mercedes?

In a few cases, the UHI connector may be found in earlier Mercedes cars going back to 2002, 2003 and 2004. Check if you have the TEL button in your Comand / Radio / Stereo. When you press the TEL button you will normally get “ Tel not activated ” or “ Telephone is not installed ” error message. This is ok.

Why does my Mercedes-Benz remote lock not Beep?

By MY2006, they should all chirp. And the chirp is not the vehicl’s fanfare horn – it’s the actual alarm siren that produces the noise. Sometime after the MY2005 facelift, MBZ changed the system to chirp by default, without the need for the “Netherlands” setting. It was phased in slowly, with the E-class first, then the CLK, and others.

Why does my car make a warning beep sound?

A single beep announces that it has been activated. If the sound continues, then the HAC could be malfunctioning or there could be an issue with the system and needs attention. Warning sounds in vehicle’s warn the driver about issues that are not set or not working properly. There could be sounds for the following:

Why does my CLK not beep when I unlock the door?

My CLK has never beeped when locking/unlocking the doors remotely. All the required lights flash 3 times, but no beeps. I have assumed that this is a ‘market’ issue, and the UK market does not need a beep. After all – what good does it do? My CLK has never beeped when locking/unlocking the doors remotely.

What causes a Mercedes Benz to not move out of Park?

If the shifter on your Mercedes-Benz will not move out of park, the first thing your should check is the battery. Once you confirm the battery is fully charged the two most common problems are a defective brake light switch or a shifter module is damaged.

What causes the brake light switch to go off?

Typically caused by clogged catalytic converter or bad MAF. Window switch. Radio says WAIT. Usually because you have entered the wrong code too many times. Break light switch. Stuck in gear or trigger the ABS/ESP light to illuminate. How to replace the brake light switch .

Why does my Mercedes have a limp mode?

Mercedes car limp mode is indicated by the check engine warning light, which activates when an issue erupts within the vehicle. If an error in the transmission causes the vehicle to jump into third gear and remain stuck in that position, you have a case of limp mode.

What causes a Mercedes to go into lime home mode?

If you are reading a P0301 through P0312 code plus another code, let say P0100. It is very likely that the P0100 fault code which refers to a malfunction in the mass air flow sensor circuit is also causing the misfire codes and even a limp home mode. Lime home mode means the transmission gets stuck in gear, typically in second gear.

Why are my CD’s not working in my car?

This condition may clear up with warmer weather, I have had problems with the CD’s in my car during cold weather. Same for my older iPod with the hard drive, it doesn’t like cold weather either. Try an iPod Nano plugged into the hidden USB port, you will never miss the CD’s.

Why does my car idle at 1500 rpm?

No more stuttering or hesitation in lower gears at 1250 – 1500 rpm. Idles like new. Advise checking electrical connections especially if vehicle lives outside in damp climate. Was this answer helpful? Well after going to the shop and running codes, and testing various things physically.

What’s the idle RPM on a 99 Vortec?

Truck recently had an exhaust manifold replaced. When its cold (as in first thing in the morning), it fires right up and high-idles for a few seconds and runs fine. After the first few seconds, its idles rough. The engine struggles to keep it above 7-800 RPM.

Why does my 2001 ML320 break by itself?

I have 2001 ML320 which I really enjoy driving, got 170K running strong. However I just ran into strange issue as I was driving, car felt like the engine was going die as it suddenly lost speed, turns out the brake is acting up by itself, then I see exclamation mark flashing in dashboard and BAS/ETS light come up.

How can I drive without fear of my ml braking itself?

You can drive without fear of your ML braking itself by pressing the ESP off button. You have to switch it off every time you start the car. Then you’ll have more time to save up for the yaw rate sensor. Don’t let it go forever. just saw the switch. You can drive without fear of your ML braking itself by pressing the ESP off button.

Why is my ML 270 CDI losing power?

My ml 270 cdi 2003 has just started to loose power (sound familiar!) – but not all of the time. When you drive off in the morning the car works fine if you put your foot down you can feel the car accelerate and hear the turbo kick in with the engine revving past 4000 rpm.

What happens when you loose power on a Mercedes Benz?

However, after about 20 min when the car has warmed up it suddenly looses power feeling very sluggish not revving beyond 2500 rpm even with your foot to the floor (almost like limp home mode but without any warning light). This makes it slow to go uphill or overtaking when you need the power.

Why is my car running on one cylinder?

If your car engine doesn’t sound like usual, there is a chance that a spark plug is worn out and the car is running on one cylinder less than usual. The cylinders in an engine have to be sealed tight so they can contain the explosions happening inside them. The car works on this basic principle.

What happens when catalytic converter is clogged in Mercedes?

If your catalytic converter is clogged you will notice a drastic drop in fuel efficiency and real struggle getting your Mercedes to accelerate. If the cat is completely clogged your car won’t even start.

What causes a cylinder to misfire in a Mercedes?

In most cases, a cylinder misfire is caused either due to old spark plugs that need to be replaced. A failed ignition coil or a bad spark plug wires. If none of the above fixes your misfire problem carefully analyze the fault codes, it is possible that misfire may be indirectly caused by another problem in the engine.

How many miles does a Mercedes spark plug last?

They are wear and tear items. Standard copper spark plugs last up to 30k miles while iridium and platinum spark plugs can last over 60,000 miles. If your Mercedes-Benz has over 80,000 miles and still has the original spark plugs, it makes sense to change the spark plugs before you pour money on any other repair.

When does the Mercedes Benz SOS malfunction warning come on?

If you don’t have access to the Star Diagnostic Tool you can have your Mercedes Benz dealer perform DTB P-B-82.95/636a, 03/24/2009 Supersedes: P-B-82.95/636 dated Oct. 29, 2008 “Instrument Cluster Message – “SOS TeleAid not Activated”” SRS Airbag Defective Warning could be triggered when the TELE AID malfunction is displayed.

Can you use the SOS button on Mercedes Benz?

They will only work if you have TeleAid or Mercedes Benz mbrace subscription. Here is what their purpose is: SOS button – use if you need emergency aid. Can I continue TeleAid Service? Yes. If you would like to use the TeleAid service you will need to upgrade the analog TeleAid unit to a digital TeleAid. Most likey at your own cost.

How to clear the TeleAid SOS warning Mercedes Benz?

For this reason we have included instruction on how to clear the Teleaid SOS warning with the STAR Diagnostic tool. In case you are wondering, Star Diagnostic is the scanner that the dealer uses to troubleshoot any system in your car and it is specific to Mercedes Benz cars.

How to disable SOS calling TeleAid in Mercedes Benz?

The module for that system is under the front passenger seat. Try disconnecting the plug and see if that takes care of the problem. The module for that system is under the front passenger seat. Try disconnecting the plug and see if that takes care of the problem.

How to recharge ML320 W163 1998-2005?

How to recharge the Air Conditioner (A/C) system of your ML-Class W163. Turn the engine on and let it idle. Turn the air conditioner ON and set it to the maximum cold setting. Open the hood of your ML320 W163 and locate the low-pressure AC service port and remove the cap. Attach the refrigerant gauge to the service port.

How can I charge my Mercedes ML320 air conditioner?

You will need to press and hold the quick-release at the end of the hose, insert it on the AC charging port then release it. Read the pressure in your air conditioner system. If the pressure is low the gauge reading will be in the white zone.

What does the Check Engine light on a Mercedes mean?

There are four buttons on the left side of the steering wheel. After pushing the button, the display will reveal why the check engine light is lit. Usually it indicates that the car is due for service. Push the lower left button on the steering wheel again and the vehicle mileage will show on the display.

When does the ESP light turn on in a Mercedes?

To check, try stopping and restarting the engine. If the light remains on after restarting get it checked at a garage as the ESP system is an important safety feature. If you have a diesel Mercedes, this light will turn on when the engine is warming up.

What to do if Mercedes check engine light is on?

1. Turn ignition to position II. All dash lights should be on. Don’t start the car. 2. Locate the OBD-II port under the dashboard. Location of OBD II port used to retrieve Mercedes-Benz fault codes. 3. Plug your OBD II scanner and let it turn on. Use an OBD II scanner to check why the Check Engine Light is ON.

How many spark plugs does a Mercedes Benz have?

Rember that Mercedes-Benz V6 and V8 engines utilize two spark plugs per cylinder. That is typical in Mercedes-Benz engines such as M112 M113 M272 M273 found on E, C, S, CL, CLK, ML, GL, G, R, SLK Class. For example, if you have an E320 (M112 engine) or E350 (M272) your car has six cylinders but requires 12 spark plugs.

Where are the fuses located in the ML320 ml500?

A second fuse box is located in the passenger footwell. This is the auxiliary fuse box. To access the fuses inside you will need to twist the two plastic locks and pull the cover towards the back of the engine. Fuses in the auxiliary panel. Relays located in the fuse and relay box by the passenger foot-well.

What to do if your Mercedes key won’t turn?

If you have this problem you will have to install a new / virgin EIS. You can not install a used unit because the EIS has to be paired / married to the car using Mercedes-Benz Star Diagnostic Software. They key itself may be the reason why the car doesn’t start. The key may open the doors, but it will not start the car.

What kind of key does a Mercedes Benz use?

While most Mercedes-Benz cars have the SmartKey some models such as the ML Class, SLK Class, Crossfire used a metal blade key up to 2005. Some models suffer from the defective key tumbler. We have seen cars with as little as 20,000 miles where the tumbler go bad. Make sure the steering wheel is not in a locked position as mentioned above.

Why does my Blend motor not move when I Turn on the AC?

This is caused by the blend motor flap getting stuck and no longer moving when you rotate the AC knob between Hot and Cold. You can manually switch the blend motor flap if you remove the glove box.

Why is there no heat in my Mercedes ML320?

Description: Trouble shoot an air conditioner and heater control in a Mercedes ML 320. Sometimes it’s just the airflow door motor that’s fried and is not opening the small door that directs the Hot or Cold air out the vents. You have to remove your dash to get to it, or…try this Loading…

Why is my Mercedes ML320 door lock not working?

The Problem: The actuators for the individual doors get damaged and jammed thus not responding to the motor when it tries to lock or unlcok the door. When using the keyfob or the dash button for locking or unlocking the doors, the jammed door actuator tries times to complete the lock/unlock action.

Where is the drain seal on Mercedes ML320 door?

Locate the hole at the edge of your door. It is covered by a rubber drain seal that prevents water from coming in the edge of your door, directly lined with your door handle from outside! Use Torx “T27” and unscrew the bolt directly leveled with the entrance cavity. Hint: You do not need unscrew it all the way.

What happens when you use the keyfob on a Mercedes ML320?

When using the keyfob or the dash button for locking or unlocking the doors, the jammed door actuator tries times to complete the lock/unlock action.

Where are the struts on a Pontiac ml?

The ML has struts in the rear. Inside each of the coil spring, you will find the shock absorber inside each spring. Rear strut and coil assembly For ML320 1999 – 2003; ML350 2003 – 2005; ML430 1999 – 2001; ML55 ML500 2002-2005 Step by Step Instruction with Pictures. Loosen the lug nuts. Raise the car up.

What kind of suspension does the ML 163 have?

The ML 163 chassis uses 4 wheels independent suspension. In the rear axle suspension, you will find coil springs that support the back of the car. The ML has struts in the rear.

Where are the coil springs on the ML 163?

The ML 163 chassis uses 4 wheels independent suspension. In the rear axle suspension, you will find coil springs that support the back of the car. The ML has struts in the rear. Inside each of the coil spring, you will find the shock absorber inside each spring.

The ML 163 chassis uses 4 wheels independent suspension. In the rear axle suspension, you will find coil springs that support the back of the car. The ML has struts in the rear.

What kind of SUV was the Mercedes ML320?

Back in 1998, all the ML320 had to worry about in the midsize luxury SUV category were the Infiniti QX4 and the Land Rover Discovery. But now, there are also the Lexus RX 300, Acura MDX and BMW X5 battling for country club supremacy. Although the first M-Class effort was generally well-received, it did have some problems.

What happens if you owe a Mercedes Benz?

Owing a used Mercedes-Benz could put a dent in your pocket, especially if you have to go to the dealer for every single repair. The list may seem long but many ML owners have put over 200k miles on the cars with only regular maintenance. The transmission and the engine on the ML are bulletproof if you only do regular maintenance.

What to do when your Mercedes goes into limp mode?

You may also get a check engine light if your transmission goes into limp mode. When a Mercedes-Benz goes into limp mode, it only operates in second gear and reverse only. When you put it in gear, you may also feel a bang as transmission engages. The first thing you should try is to check the transmission fluid level.

What causes a Mercedes-Benz transmission to fail?

We see these transmission fail in rare cases when water enters the transmission via the oil cooling lines or the radiator on cars equipped with Valeo radiators. The top part of the radiator on your Mercedes-Benz contains the chamber for the engine coolant/antifreeze while the bottom part contains the chamber for the transmission oil cooling.

Where are the transmission codes stored in a Mercedes?

Specific codes related to the transmission are stored in the TCU (Transmission Control Unit) and come generic codes such as P0705 are stored in ECU (Engine Control Unit). You don’t need to pay anyone to read the codes; you can retrieve them yourself in a couple of minutes with the right OBD II scanner.

Where are misfire codes stored in a Mercedes?

Luckily for you, the misfire codes are stored in the ECU and are very easy (and inexpensive) to retrieve. To diagnose an engine misfire on a Mercedes all you need is a generic OBD II code reader that can be bought in some cases for under 20 at your local auto parts store or on Amazon’s Best Selling OBD II scanners list.

Can a clogged catalytic converter cause a misfire?

A catalytic converter that is clogged and is restricting the exhaust gasses from leaving the engine can also trigger multiple cylinder misfire. If your catalytic converter is clogged you will notice a drastic drop in fuel efficiency and real struggle getting your Mercedes to accelerate. If the cat is completely clogged your car won’t even start.

What happens when a Mercedes engine misfire occurs?

As soon as an engine misfire occurs on a Mercedes-Benz, you will notice poor engine performance and strange vibrations that in some cases can be felt even in the driver cabin. The first thing that comes to mind when you get an engine misfire is: “This is going to be expensive.” Take a deep breath because in most cases it doesn’t have to be.

How to test a Mercedes Benz fan blower motor regulator?

This is the blower motor resister, which controls the fan speeds. Disconnect the multi-wire connector from the blower motor resister next to the blower motor. Start the car and turn the air conditioning on. Test the connector for power at the terminals in the connector using the voltmeter. If there is power, reinstall the connector to the resister.

Where is the resister on a Mercedes Benz fan?

Just to the left of the blower motor, an electrical connector connected to a flat 1-inch-by-2-inch plate can be seen. This is the blower motor resister, which controls the fan speeds. Disconnect the multi-wire connector from the blower motor resister next to the blower motor. Start the car and turn the air conditioning on.

Why does my car fan keep running after I Turn Off the engine?

Running cooling fans help cool down the engine even after you turn off the car. Common Causes. If your cooling fan runs for over 10 minutes after turning off the engine, you may have a problem that needs to be fixed. Here are some possibilities causing the fan to stay running longer. low coolant level, faulty coolant temperature sensor,

Why is my fan limit switch not pressed in?

If your fan limit switch was already set to AUTO (not pressed in), then you most likely either have a problem with your thermostat wiring or the fan limit switch is bad.

Why does my Mercedes-Benz A / C blower run uncontrolled?

But under fault conditions it could fail as ‘always on’ or ‘never on’. Mostly (according to this forum) a failed BR causes the a/c blower to run uncontrolled. Btw your WIS a/c circuit diagram is not identical to mine for W208. However the blower motor/regulator part is the same.

Why does my humidity control fan keep running?

If your humidity controlled fan has a pull cord, it is also possible that somebody has pulled the cord to the override position, in which case the fan will run continuously until switched back to the sensor mode.

What are the common problems with a W163?

We have worked on and owned several W163 and have put together the list of common problems for you. MLs share the M112 engine found in the ML320 and the M113 engine found on the ML430, ML350, ML500. The 722.6 gearbox installed in the ML is one of the most reliable transmission produced. ABS/ETS/ESP lights. Needs replacement of ABS pump.

What are the most common Mercedes Benz transmission problems?

Top 5 Mercedes-Benz Transmission Problems. Won’t come out of Park gear due to a defective brake light switch. ( DIY How to replace the Brake Light Switch) Continue to read if you would like to learn how to troubleshoot your Mercedes-Benz transmission yourself and where you should start. 1. Check Fluid Level

What causes a Mercedes Benz 4Matic transfer case to fail?

The typical symptoms of failure are noise when cold and vibration. Also, the rubber flex disc can degrade and the rubber can separate from metal and cause a vibration. When it comes to fluids, the 4MATIC transfer case uses automatic transmission fluid that meets Mercedes-Benz standards.

How long does it take to replace a water pump in a Mercedes?

The design is very simple, allowing for easy removal and installation. Replacing the water pump in your Mercedes should only take you a couple hours to complete. Take the cap off of the Mercedes radiator and also off the coolant overflow reservoir.

Is the Mercedes ML 320 a good car?

I just bought a used 1998 ML 320. What a gem!!!! Plenty of power/torque, good acceleration, and an AWD system that handles itself great in the snow. Everything works, leather is in perfect condition, Bose stereo is fantastic, everything is what you would expect from a Mercedes Benz.

What’s the RPM of a car at low speeds?

Also, when this issue starts happening, even though I am driving at very low speeds from 25-35 mph, the RPM increases to around 2800. When I attempt to accelerate, it cannot go over second gear. There is also a problem while downshifting from second to first gear.

What causes high rpm at low speeds CHR?

Automatic transmission issues, high RPM at low speeds chr… Recently, I’ve been having transmission issue with my car. It is an automatic and shifting is very hard. It doesn’t seem to shift over second gear. It occasionally shifts into third gear within a mile of driving, but after that, it cannot shift over second gear.

Can a car go over second gear at low speeds?

It occasionally shifts into third gear within a mile of driving, but after that, it cannot shift over second gear. Also, when this issue starts happening, even though I am driving at very low speeds from 25-35 mph, the RPM increases to around 2800. When I attempt to accelerate, it cannot go over second gear.

What happens when a Mercedes Benz goes into limp mode?

When a Mercedes-Benz goes into limp mode, it only operates in second gear and reverse only. When you put it in gear, you may also feel a bang as transmission engages. The first thing you should try is to check the transmission fluid level. The transmission has a dipstick tube but with no dipstick in it.

Why does my Mercedes not start when I charge the battery?

This Mercedes-Benz is not starting because of a low battery. In this case, what you need to do is trickle charge your battery using any of these 12 volt battery trickle chargers. If you need help read this article on How to charge a Mercedes-Benz the right way. Mercedes won’t start, and it’s not the battery.

Why is my Mercedes Benz starter not working?

Often times, when the starter is defective or seizes up it will blow out the fuse that protect the starter circuit. Another thing that you can try is to hit the starter with a rubber hammer a couple of times. Depending what kind of starter problems you have, the starter may work a few more times.

Why is my ML320 blowing hot air even when the AC is on cold?

Is your ML blowing hot air even though you have the AC on cold setting? A common problem with the ML320 / ML430 is the AC getting stuck on Hot or Cold setting. This is caused by the blend motor flap getting stuck and no longer moving when you rotate the AC knob between Hot and Cold.

Why does my Mercedes ML320 have a dead battery?

Marty : Ok, then it sounds like the cylinder may be froze. Usually this is from having never used the key in the cylinder.

What’s the price of a 2001 Mercedes-Benz ML 320?

Get KBB Fair Purchase Price, MSRP, and dealer invoice price for the 2001 Mercedes-Benz M-Class ML 320 Sport Utility 4D. View local inventory and get a quote from a dealer in your area. Home Car Values Price New/Used

How much does a Mercedes-Benz ML320 cost?

Overview Overview Starting MSRP $36,300 See M-Class Invent Engine Type Gas Transmission 5-speed shiftable automatic Drive Type All wheel drive Cylinders V6

What kind of engine does the Mercedes ml500 have?

New for 2002, the 5.0-liter ML500, our test vehicle, replaces last year’s 4.3-liter ML430. Mercedes-Benz covers a wide spectrum with its M-Class sport-utilities. The ML320 delivers the rugged looks, room, safety and utility that high-end SUV buyers seek along with a V6 engine that keeps pricing down to earthly levels.

What kind of car is the Mercedes ML 320?

Used 2000 Mercedes-Benz ML 320 4MATIC New Listing $2,995 Regan Motors Used 2000 Mercedes-Benz ML 430 4MATIC $3,990 Divan Auto Group Used 1999 Mercedes-Benz ML 430 4MATIC $3,995 Reduced Bittons Auto Sales Used 2000 Mercedes-Benz ML 430 4MATIC $4,499 Private Seller Used 2000 Mercedes-Benz ML 320 4MATIC $4,995 Reduced Ride One Auto Sales Used 2001

What causes an underboost code on a p0299?

Potential causes of a P0299 turbo underboost code include: 1 Intake (induction) air restriction or leak. 2 Failed or damaged turbocharger (sticking, binding, etc.) 3 Faulty boost/charge pressure sensor. 4 Faulty wastegate bypass regulator valve (VW). 5 Low fuel pressure condition (Isuzu). 6 (more items)

What does code p0299 mean on Duramax Diesel?

On the GM Duramax diesel, this code may mean the turbo housing resonator has failed. If you have a Ford, you’ll want to next check the wastegate regulating valve solenoid for correct operation. Anecdotally in Fords, this seems to be found in EcoBoost or Powerstroke engine equipped vehicles such as F150, Explorer, Edge, F250/F350, and Escape.

What kind of cars are affected by p0299?

Brands of vehicles affected may include but are not limited to Ford, GMC, Chevy, VW, Audi, Dodge, Hyundai, BMW, Mercedes-Benz, Ram, Fiat, etc. Although generic, the specific repair steps may vary depending on make/model.

Is there a problem with the throttle sensor on a Mercedes?

Mercedes-Benz throttle body or throttle position sensor found on C-Class, E-Class, S-Class, CLK-Class, SLK-Class may fail causing idle issues, no idle or poor acceleration. Symptoms of defective Mercedes throttle body or throttle position sensor include:

What to do if your throttle possition sensor has failed?

If you determine the throttle position sensor has failed on your Mercedes-Benz you will need to address this problem right away. In most cases, you will get code P0120 or P012x. Your options are to replace it with a new throttle position sensor. Mercedes-Benz dealerships would be happy to help you or any Indepdement mechanic.

How do you reset the throttle on a Mercedes?

First, try throttle reset procedure Turn the key to ON position. Position II that is. Press and hold the gas pedal for at least five seconds. Keep the pedal pressed. Turn ignition off but do not remove the key. Now release the gas pedal. Remove key. Wait a minute before you restart your Mercedes.

Where is the fuse box panel located on a Mercedes-Benz ML320?

Where is the fuse box panel located on a Mercedes-Benz on a ML320, ML350, ML430, ML500? The main fuse box is located in the engine compartment, driver’s side. Auxiliary fuse box is located inside the cabin, in the passenger foot well. The main fuse box is located in the engine bay.

https://www.youtube.com/watch?v=aH3tkqtizK8

Where do you find the radio code on a Mercedes Benz?

Follow these steps if you need the Radio Code for your Mercedes-Benz. First take a look at your owners manual booklet. The code may be written down on a small business card size letter. Locate the VIN on your car. On your Mercedes-Benz, you can locate the VIN if you open the drivers door and look for a tag like the one below.

How to fix stuck flap on ML320 ml430?

You can also manually switch the stuck flap to COLD settings if you need a temporary solution. Overwise buy the part above and replace it. This opens in a new window. Start by removing the glove box. Open the glove box and you will see the four screws that hold it in place.

Is the Mercedes ML320 CDI available in Australia?

NSW Distance from me? QLD Distance from me? NSW Distance from me? QLD Distance from me? VIC Distance from me? SA Distance from me? VIC Distance from me? WA Distance from me? VIC Distance from me? QLD Distance from me? NSW Distance from me?

How many miles can you put on Mercedes?

There is no simple answer as to how long or how many miles a Mercedes-Benz is good for. Some models have issues as early as 50k miles while other models can go over 200k miles with just regular maintenance.

What causes the Check Engine light to turn on on a Mercedes ML350?

A faulty camshaft adjuster solenoid affects the ease of driving the Mercedes ML350, causing the Check Engine light to turn on after a reported average of 80,839 miles. The mileage discrepancy for this issue is also large, with reports of this failure occurring after as few as 9,948 miles or as many as 184,000.

Why is my Mercedes-Benz transmission not shifting?

If cracks develop between the two chambers, coolant will mix with transmission oil and it will destroy the transmission. This has been a well-documented issue for Mercedes-Benz cars equipped with the Valeo radiators.

How to reset adaptive shifting points on Mercedes Benz?

This procedure will reset the adaptive shifting points in your Mercedes-Benz automatic Transmission Control Unit (TCU). These simple do it yourself instructions take less than 5 minutes. No tools are required to perform this procedure and make your Mercedes-Benz shift like new. Try this if your car has been shifting sluggish recently.

How long does it take to shift a Mercedes Benz?

These simple do it yourself instructions take less than 5 minutes. No tools are required to perform this procedure and make your Mercedes-Benz shift like new. Try this if your car has been shifting sluggish recently. This will make your car fun to drive again, it’s like getting a free tune-up.

What happens when you reset the transmission shift points?

It is not going to make your shifting abnormal. If your gear shifts are abnormal you have something else going on. Resetting the transmission shift points makes the transmission the same as when the car is out of the factory. Within 30 driving cycles, the ECU will monitor your driving habits and adapt the shifting points to your driving style.

Can a 2000 ml run for 10 minutes?

It will if u keep it running for 10 minutes.. On the early pre 2000 ml’s the aam can loose it’s settings when disconnected from the battery. These can include the ignition key sync or even the keys rfid information. If when you try to start it starts then run some for maybe a half second before shutting down this could be your problem.

What are the parts of the Mercedes ML320?

Mercedes Benz ML320 Parts & Accessories. Mercedes Benz ML320 A/C Compressor. Mercedes Benz ML320 Alternator. Mercedes Benz ML320 Axle Assembly. Mercedes Benz ML320 Ball Joint. Mercedes Benz ML320 Blower Motor. Mercedes Benz ML320 Brake Booster. Mercedes Benz ML320 Brake Caliper. Mercedes Benz ML320 Brake Disc.

Is the Mercedes Benz ML320 used in Lost World?

Before the Mercedes Benz ML320 was officially launched, Mercedes Benz allowed the use of two pre-production ML-Class SUVs in the film Lost World: Jurassic Park. This early exposure was a marketing success that significantly raised the sales figures of the popular SUV.

How much does a 2002 Mercedes Benz ML cost?

Mercedes-Benz ML 320 4MATIC $5,000 Fox Auto Center Inc Used 2000 Mercedes-Benz ML 320 4MATIC $5,399 sandiegocarforsale.com Used 2002 Mercedes-Benz ML 500 4MATIC $5,950 Championship Motors at Bear Creek Used 2004 Mercedes-Benz ML 500 4MATIC $6,500 BMW MINI of Sterling Used 2003 Mercedes-Benz ML 350 4MATIC $7,495 Industry Motors Used 2003

How much does a Mercedes Benz ML 500 cost?

Mercedes-Benz ML 500 4MATIC $5,950 Championship Motors at Bear Creek Used 2004 Mercedes-Benz ML 500 4MATIC $6,500 BMW MINI of Sterling Used 2003 Mercedes-Benz ML 350 4MATIC $7,495 Industry Motors Used 2003 Mercedes-Benz ML 350 4MATIC $11,000 VW-BENZ Used 2003 Mercedes-Benz ML 350 4MATIC New Listing $13,995 Geneva Motorcars Used 2000

Is there a temperature sensor on the MAF?

The MAF also incorporates an internal intake air temperature sensor which measures the temperature of the intake air. The first indicator that you might have a problem with the MAF is the presence of a check engine light (CEL) on your dashboard.

What causes a check engine light on a MAF?

The first indicator that you might have a problem with the MAF is the presence of a check engine light (CEL) on your dashboard. The check engine lamp can be caused by a wide variety of problems with the engine: you need to read the codes from the computer to get a starting clue as to what the problem is.

How do you remove the MAF sensor on a Mercedes Benz?

There are two T20 Torx security screws (red arrows) that hold the MAF sensor in the housing. You can remove these with the housing in or out of the car.

Navigation