Why is my GMC Yukon 4×4 not working?
The truck has never been in accident that I know of so there is no damage to the front axle. The truck has 190k on it, but the engine only has about 60k. The noise it was making last winter sounded like it was coming from the front axle. It sounded like a wheel bearing or a rear end whine but I only heard while in 4wd.
What are the symptoms of a bad ECM power relay?
A bad relay may cause the vehicle to crank, but not start, or sometimes not even crank at all. 3. Battery drain or dead battery. A failed ECM power relay can also cause a battery drain or dead battery. If the relay shorts it can leave power on to the computer, even when the vehicle is turned off.
Can a bad fuse cause an electrical problem?
Check for bad fuses by taking them out one by one. A bad fuse is the most likely cause of electrical problems, so start with this step before taking your car apart trying to find the bad wire or contact point.
Why does my 4×4 light not come on?
It sits exposed on the front axle and is easily damaged. The 4Hi and 4Lo lights just flash but 4WD does not engage. Also the ‘SERVCE 4WD’ light does NOT come on ruling out transfer cases problems. Get under the front of the truck and check the actuator.
Why is my 4WD light not working on my Chevy Tahoe?
There have been about 3 or 4 times it has went out and stayed out for about a day. Then it would come back on. As of this moment now, the Service 4wd light is on. The lights only come on when I start the truck, then all four come on for a couple of seconds then go back out.
Is the service 4WD light on or off?
The service 4wd light has been on and stayed on almost the whole time I’ve had this issue. There have been about 3 or 4 times it has went out and stayed out for about a day. Then it would come back on. As of this moment now, the Service 4wd light is on.
Why does my Yukon XL have a 4WD light?
I was recently getting a service 4wd light in my 03 yukon xl. the lights for the switch also went out. I crawled under the truck and started looking at connections to the transfercase. I found that one of the connections had a small amount of corrosion in it. I pulled it apart, sprayed it with contact cleaner and reassembled.
Why are there no lights on my 4WD suburban?
Last week the message does not go away after restarting the car so I pull out the selector switch and resolder the joints then plug it back in to find that the “Service 4WD” message is gone but there are no lights at all. I press the buttons but nothing happens. I’m in 2WD.
I was recently getting a service 4wd light in my 03 yukon xl. the lights for the switch also went out. I crawled under the truck and started looking at connections to the transfercase. I found that one of the connections had a small amount of corrosion in it. I pulled it apart, sprayed it with contact cleaner and reassembled.
The truck has never been in accident that I know of so there is no damage to the front axle. The truck has 190k on it, but the engine only has about 60k. The noise it was making last winter sounded like it was coming from the front axle. It sounded like a wheel bearing or a rear end whine but I only heard while in 4wd.
There have been about 3 or 4 times it has went out and stayed out for about a day. Then it would come back on. As of this moment now, the Service 4wd light is on. The lights only come on when I start the truck, then all four come on for a couple of seconds then go back out.
Last week the message does not go away after restarting the car so I pull out the selector switch and resolder the joints then plug it back in to find that the “Service 4WD” message is gone but there are no lights at all. I press the buttons but nothing happens. I’m in 2WD.
Why are there no lights on my 4WD?
2006 silverado 1500. 4×4 would not engage on mine. I would receive service 4wd message on dash and 4wd switch would change light locations randomly. Changed swich and it did not fix the problem.
Why does my 4 wheel drive not engage?
The transfer case could pose another reason why your 4 wheel drive fails to engage. This could be due to the vehicle not coming to a complete stop to allow it to engage. This is because the splined pin and gears of the actuator need to align 100% with the gears inside the transfer case.
Is the GMC Suburban 4WD transfer case working?
Oh BTW I have a 99 GMC suburban with the auto 4wd transfer case. Last winter when I would put it in 4wd it was making a bad noise (almost like a wheel bearing roaring) but the 4wd was working then.
The transfer case could pose another reason why your 4 wheel drive fails to engage. This could be due to the vehicle not coming to a complete stop to allow it to engage. This is because the splined pin and gears of the actuator need to align 100% with the gears inside the transfer case.