Why does my Mazda RX-8 stall at 3000 rpm?
The rough idle appeared to go away after driving a long highway trip where RPM tended to remain above 3000 for long periods. I believe there are two things going on with the RX-8 AT. The engines simply need to run at least at 3000RPM to keep everything clean and clear.
How to fix a Mazda that stalls at stop?
Remove the air hose from the throttle body. Disconnect the throttle body connector. Remove the throttle body from the intake manifold, with the water hose connected. Clean the throttle body on the air hose side using a soft, clean shop cloth, sprayed with engine cleaner (Mazda recommends their P/N 000-77-A86).
Which is better Mazda crossfire or Mazda RX 8?
While the RX-8 is one of the purest sports cars on the road, the Crossfire is more of a GT car. Although it’s undeniably a fine car, I don’t think the Crossfire really compares to the RX-8 from a sporting point of view – plus, it doesn’t have a back seat.
When to use full automatic on Mazda RX-8?
1) Don’t use the full automatic in city driving. 2) For 20MPH use only 1st gear. 3) For 35MPH use only 2nd. 4) For 45MPH use only 3rd gear.) If you are traveling highway speeds above 65MPH full automatic is OK.
Why does my Mazda RX-8 engine not start?
At the time it sounded like the battery, because engine turned very slowly. Since, I’ve changed battery, checked all fuses, and engine still doesn’t start (though it engine turns fine). Would you please assist me with any info which will help me to determine what’s wrong.
Why is my Mazda RX-8 stalling and stalling?
You feel it in the brake pedal,steering wheel,doors, and you can see the vibration in the mirror’s.Dealer said that their scanner/computer show that everything is in the NORMAL RANGE LIMITS……. The motor mounts have been checked and show no signs of wear.
How does the Mazda RX8 Renesis engine work?
(See NO.8 ENGINE RUNS ROUGH/ROLLING IDLE .) 9 Fast idle/runs on The engine speed continues at fast idle after warm-up. The engine runs after the ignition switch is turned off.
How to troubleshoot an RX8 rotary engine?
(w) RX8-Engine Troubleshooting Page 2 Inspection Method for Sensor Connectors or Wires 1. Connect the WDS or equivalent to the DLC-2. 2. Turn the ignition switch to the ON position (Engine off). NOTE: If the engine starts and runs, perform the following steps at idle. 3. Access the PIDs for the switch you are inspecting.
How many miles does a Mazda RX8 engine last?
Generally speaking, the Mazda Rx8 engine can last about 60,000 miles. It is important to keep in mind to maintain your engine and make sure that you take your car into a mechanic when you have issues. What are some of the most common complaints About the Mazda Rx8 & the Engine?
What to do if your Mazda RX-8 won’t start?
If the lights anywhere in your car are not turning on, your battery may be dead. Check to see if you can start your engine. If the engine turns on then your battery should be working properly. However, if the engine will not start, refer to the Car Cranks But Won’t Start .
Why is the oil in my Mazda RX-8 so dirty?
As you drive the car the oil picks up impurities in the engine and can lose some of its lubricating properties. Because in the RX-8 the oil is introduced inside the engine it is even more important that the engine oil remain clean and fresh.
The rough idle appeared to go away after driving a long highway trip where RPM tended to remain above 3000 for long periods. I believe there are two things going on with the RX-8 AT. The engines simply need to run at least at 3000RPM to keep everything clean and clear.
If the lights anywhere in your car are not turning on, your battery may be dead. Check to see if you can start your engine. If the engine turns on then your battery should be working properly. However, if the engine will not start, refer to the Car Cranks But Won’t Start .
When did the Mazda RX-8 come out?
This category covers 2004, 2005, 2006, 2007, 2008 Mazda RX-8 Troubleshooting models. Your guide to finding the problems with your Mazda RX-8 so you can effectively and efficiently resolve them.
As you drive the car the oil picks up impurities in the engine and can lose some of its lubricating properties. Because in the RX-8 the oil is introduced inside the engine it is even more important that the engine oil remain clean and fresh.
Can you put ATF in a flooded engine?
ATF does not usually sit in a flooded engine long enough to cause damage to the seals, as shortly after the ATF is poured into the engine it is burned off on startup. However, oil works just as well and is much more benign. There you have it, when you can and when you cannot use ATF.
When to use the ATF trick in RX-7?
If you have been involved in the RX-7 community, you have probably heard mention of the “ATF trick”, or “ATF treatment”. It is often prescribed for serious flooding situations, and sometimes as a general maintenance item. Especially on a certain forum.
Can a Mazda RX 8 engine be rebuilt?
And mazda is building a factory according to their announcements to rebuild failed motors, but they will probably be rebuilt the same as the failed ones and use the same required oil to only fail again and again. Good luck with your RX 8.
What should I do if my Mazda RX8 floods?
Wait at least three seconds before trying again. Warming the engine prior to turning it off will help prevent future flooding. Once the engine starts, let it run to make sure the engine has warmed before turning it off.
Is it possible to have a flooded engine?
A flooded engine seems to be a problem of the past. Thanks to modern fuel injection technologies in collaboration with other modern systems its seem to be solved for good. Nevertheless, it still does happen although mostly on high-mileage, used cars where the fuel intake system isn’t in its prime condition anymore.
Why does my Mazda RX8 not start up?
by Darla Ferrara. The rotary engine of a Mazda RX8 tends to saturate easily if the car turns off before the engine warms. Flooding the cylinders by injecting excessive fuel into the combustion chamber causes the fuel/air ratio to become disproportionate. When this happens, ignition cannot occur, and the engine cannot start.
ATF does not usually sit in a flooded engine long enough to cause damage to the seals, as shortly after the ATF is poured into the engine it is burned off on startup. However, oil works just as well and is much more benign. There you have it, when you can and when you cannot use ATF.