Why does my Harley Davidson make a hard clicking sound?
Clicks when trying to start does not engage. I have a Harley-Davidson 1999 sportster 1200. I get a hard fast clicking sound when trying to start. I Have put the battery on a charger and let it charge overnight. It still does the same thing. Is this a bad battery?
Why do I hear clicks when trying to start my bike?
Learned from Harley Dealer to never jump bike with vehicle running. It’s too much juice. When trying to start while hooked u to started vehicle, head light was strong implying it should start, but not the case. Instead I just heard rapid clicking sound. Thought it was starter or solenoid. Very loud. Put new battery in and started right up.
Why does my car click when trying to start?
However, when the hold in coil is out on the starter solenoid it will do the same thing that you are just describing. In that case you need a new starter motor or you could try to rebuild your solenoid. The starter motor and is very easy to swap out. First, disconnect your battery. Do not skip this step.
Clicks when trying to start does not engage. I have a Harley-Davidson 1999 sportster 1200. I get a hard fast clicking sound when trying to start. I Have put the battery on a charger and let it charge overnight. It still does the same thing. Is this a bad battery?
What makes the solenoid hold in coil click?
The starter will either push the jack shaft out and spin (then the starter is good )or the jackshaft will click in and out rapidly and then you’ll know it’s the solenoid hold in coil. But it’s probably just the battery. Was this answer helpful? What is the holding coil?
Why does my ignition coil stop working on my Harley Davidson?
The longevity you get from your coil may depend on usage, demand on the coil or environmental conditions. The coil’s capacity may diminish over time, or simply stop functioning at once. If it is determined that your motorcycle has no spark; do not just assume that the problem is your coil.
What kind of coil does a Harley Davidson use?
The secondary of the coil is the area/towers where the spark plug wires plug in. There are two types of coils used on most Harley-Davidsons. Dual fire and single fire. Dual fire coils send spark to both cylinders, all the time. Regardless of which cylinder is on the compression stroke.
Why does my external hard drive make clicking noise?
Most laptops, desktops, and external hard drives operate with minimal sound. The amount of sound can depend on the quality of manufacture and how well insulated moving parts are, so they operate more quietly. Some may quietly click occasionally as the actuator arm in the hard drive hits a limiter.
How to fix clicking noise in hp speakers?
1 It looks like a hardware issue with the speakers or the sound card of the AIO. 2 To isolate the issue correctly, please ensure that you connect an external headset or earphones to the computer’s audio port and check if the clicking noise occurs on these. 3 Please contact HP phone support to get the speakers replaced.
What kind of noise does a 2010 Harley Davidson make?
Discussion in ‘ Transmission ‘ started by bo54gey, Sep 30, 2010 . I have a 2010 FLHTK that is less than two months old and 1800 miles on it. The other day I returned it to the dealer for a rattling/banging noise in the primary case.
Most laptops, desktops, and external hard drives operate with minimal sound. The amount of sound can depend on the quality of manufacture and how well insulated moving parts are, so they operate more quietly. Some may quietly click occasionally as the actuator arm in the hard drive hits a limiter.
When did I replace the battery on my Street Glide?
I have a 2014 Street Glide Special with about 40k miles. I replace the main battery in February and then last week I took the bike for a ride. After stopping for a drink, the bike would not start.
Why does my car make a clicking sound when I start it?
Thought maybe its the battery. Took the battery to local auto parts store and checked out just fine with good charge. Put battery back in and hit start same click sound. After repeatedly clicking the start button I tracked the sound to the starter relay.
Why does my bike make the same clicking sound?
Put battery back in and hit start same click sound. After repeatedly clicking the start button I tracked the sound to the starter relay. Well with one hand moving the relay around and one pushing the start button bike would start up. After that I put off fixing it for a while and had been starting it the same way. That was until yesterday.
I have a 2014 Street Glide Special with about 40k miles. I replace the main battery in February and then last week I took the bike for a ride. After stopping for a drink, the bike would not start.
Thought maybe its the battery. Took the battery to local auto parts store and checked out just fine with good charge. Put battery back in and hit start same click sound. After repeatedly clicking the start button I tracked the sound to the starter relay.
Put battery back in and hit start same click sound. After repeatedly clicking the start button I tracked the sound to the starter relay. Well with one hand moving the relay around and one pushing the start button bike would start up. After that I put off fixing it for a while and had been starting it the same way. That was until yesterday.
Why does my starter click when trying to start?
The starter will either push the jack shaft out and spin (then the starter is good )or the jackshaft will click in and out rapidly and then you’ll know it’s the solenoid hold in coil. But it’s probably just the battery. Was this answer helpful?
Always Check this first! Clicking sound and the inability to start can usually be caused by low power being supplied to your car’s starter motor. Open up the car hood and check the car battery.
The starter will either push the jack shaft out and spin (then the starter is good )or the jackshaft will click in and out rapidly and then you’ll know it’s the solenoid hold in coil. But it’s probably just the battery. Was this answer helpful?
What kind of bike does a 1992 fxrp have?
Bike is a 1992 FXRP with 1340cc evo engine. Hast the starter where the the starter and solenoid are one unit. Hoss, I would tend to agree with you on the solenoid, bypassing to the starter and same results kind of points to the starter as well, since the starter and solenoid is one piece replacing both should solve your issue.
Why was the Harley Davidson FXR made from scratch?
The company was working on the FLT when they realized that they needed to design a bike for the newer audience. However, they didn’t really have the money or the time to start building the FXR from scratch. Their only option was to build the bike with a new frame and the same drive train as the FLT. They already knew what their goal was.
What to do if your Harley Davidson won’t start?
Try looking under the Seat or the left side cover . if the thing clicks look for the clicking were it’s coming from . Okay thanks sounds like a plan. Start simple. Like SCHMIDTYS said, clean, tight connections. A little sand paper or a wire brush on the posts and connectors and a screwdriver is all you need.
Learned from Harley Dealer to never jump bike with vehicle running. It’s too much juice. When trying to start while hooked u to started vehicle, head light was strong implying it should start, but not the case. Instead I just heard rapid clicking sound. Thought it was starter or solenoid. Very loud. Put new battery in and started right up.
Try looking under the Seat or the left side cover . if the thing clicks look for the clicking were it’s coming from . Okay thanks sounds like a plan. Start simple. Like SCHMIDTYS said, clean, tight connections. A little sand paper or a wire brush on the posts and connectors and a screwdriver is all you need.
Why does my Harley Davidson run weird after a charge?
The reason its intermittent is the bike will start running weird in other words it would take a charge but if for some reason that charge did not hold for long the bike will start running weird again. So I went and change the battery and I’ve never had the problem since.
What was the problem with my Harley Davidson?
After about 15 mins she showed up and said her bike would not stay running. At each stop, it would stall but would always start after the fact. It died in the driveway. We tried to troubleshoot the problem but have been unsuccessful so far. Checked the fuel pump, getting gas, changed the plugs and checked the wires for leaks, no leaks.
The starter will either push the jack shaft out and spin (then the starter is good )or the jackshaft will click in and out rapidly and then you’ll know it’s the solenoid hold in coil. But it’s probably just the battery. Was this answer helpful? What is the holding coil?
Can you remove the starter from a bike solenoid?
Once you have the starter off and the solenoid apart, you will see a copper washer and the contact from the + wire. There will be a lot of burn marks on both. You can either sand the marks off the washer or flip it over. On some bikes you can dis assemble the solenoid without removing the starter, which is a pain in the butt most times.
Why is my relay not working on my Harley?
Meter the current at the solenoid. It only takes a few mA on a relay coil to close it, but the solenoid has a lot bigger coil that draws more current to move. I have fought through the same issue with a few different old autos. Wires just get old and tired.
How does the solenoid work on a Harley Davidson?
When power is applied to the solenoid, a retractable pinion gear is pulled into place between the engine’s starter clutch and the starter motor. This action is followed by a distinct click before the engine is cranked to life.
How do you retract starter solenoid on Harley Davidson?
Connect the free clip to the starter relay terminal on the left side of the starter solenoid. The solenoid pinion gear, exposed at the inner face of the solenoid, should click and retract into the starter housing. The starter solenoid is defective if the pinion gear does not retract.
Why is my Harley Davidson Dyna Glide not starting?
If your battery voltage and connections are in good condition, but your engine is still refusing to turn over, the problem may be in the starter circuit. Perhaps the easiest place to begin is at the starter solenoid on the right side of the motorcycle.
Can a bad starter relay be a solenoid problem?
Sometimes the starter itself is the problem. Electrical issues can be annoying and inconvenient. They can also be hazardous and can cause damage. If you run into symptoms of a bad starter relay or solenoid with your car, truck, or SUV, make sure to have a trusted technician to diagnose the specific problem.
Why does my bike starter keep clicking repeatedly?
Anyway I came back to the house and hooked my battery charger straight to the power and ground battery cables on the bike and set it to the 50 amp position on the charger for starting and gave it a go. Still same thing charger just clicks repeatedly. It has the power for sure because that charger can start a car.
What does hard fast clicking on a bike mean?
Hard fast clicking is starter motor below its full voltage, best charger to have is a optimate 3 or above,this will desulvate your battery,charge it,and be fully charge by morning,I have a optimate3 and a yellow gel battery.I plug my in after every ride,and mine fires first time everytime.
Why does my bike click when trying to start?
SOLVED: Clicks when trying to start does not engage. – Harley-Davidson Sportster Evolution – iFixit Clicks when trying to start does not engage. I have a Harley-Davidson 1999 sportster 1200. I get a hard fast clicking sound when trying to start. I Have put the battery on a charger and let it charge overnight. It still does the same thing.
What to do when your Harley Davidson won’t start?
Try neutral with clutch pulled in. Also battery connections , solenoid wire. The security system lights only flash after I turn off the bike. I have the bike in neutral and I even tried pulling in the clutch a couple of times. I checked the wire to the solenoid and it had power.
What to do when your motorbike wont start?
Look up direct start button cover. It can get you out of a jam when the solenoid acts up. Won’t help if the battery is to low to crank the engine though. Was this answer helpful? I dont own a motorbike.
Why does my Harley Sportster engine not start?
It has been suggested that I bridge the terminals on the solenoid and if all is well the engine should turn over and probably start The likely issue is the battery itself. Although it has voltage, the plates & electrolyte/electrolytic gel have lost their ability to create the needed amperage to push that voltage.
SOLVED: Clicks when trying to start does not engage. – Harley-Davidson Sportster Evolution – iFixit Clicks when trying to start does not engage. I have a Harley-Davidson 1999 sportster 1200. I get a hard fast clicking sound when trying to start. I Have put the battery on a charger and let it charge overnight. It still does the same thing.
What does a click mean on a starter relay?
If the voltage drops below 9.5 vdc, the battery is junk. If the voltage stays at 12, the start button, or more likely the starter relay is junk, that also holds true with a “click” & is the next diagnostic, a new starter relay. If the voltage drops but stays above 10-11 vdc, & there is a “click” check the battery cables & again, the starter relay.
How to check spark plugs on Harley Davidson Sportster?
Insert a spark tester into the wire and attach the tester to ground. Remove the fuel pump fuse. Refer to the article Fuse Box Information for fuse locations. Crank the engine and watch for spark. If spark is consistently present, the problem most likely lies with the spark plugs and you should continue to Step 2.
Where do you start on a Harley Davidson Sportster?
Always start at the fuse box when your Sportster experiences an electrical problem. This article applies to the Harley Davidson Sportster (2000-2015). Fuses, relays, and circuits breakers: they’re all circuit protection devices that can be found inside your Sportster’s fuse box, depending on its year.
Why is my Harley Davidson Sportster not igniting?
One of the most common sources of electrical problems is the battery. Test the battery’s state of charge and current capacity by reading Step 2 of the article Electrical Diagnostic Guide. If no spark is present at the end of the spark plug wire, the air/fuel mixture cannot ignite.
Is the solenoid on the starter on Your 94?
Brian : Yes on your 94 the solenoid is on the starter. Customer : It has been suggested that I bridge the terminals on the solenoid and if all is well the engine should turn over and probably start Brian : The likely issue is the battery itself.
Where is the starter on a Harley Davidson 883 Sportster?
Connect your red probe to the solenoid positive wire. This is a fat 12 or 14 gauge wire on the cylindrical portion of the starter. Connect the black probe to a known good ground. 12v should be present in this wire at all times. Figure 3. The starter location on a 883 Sportster.
Why is my Harley Davidson Sportster not starting?
Place your Sportster in second or third gear for the best results. A battery that can’t start your engine may no longer be recharging properly because of its age and current state of charge. The ground cables that connect the battery to your Sportster frame must also be undamaged and free of corrosion.
How do you test a starter solenoid on a Harley Davidson?
Connect one clip to the battery’s positive terminal. Connect the free clip to the starter relay terminal on the left side of the starter solenoid. The solenoid pinion gear, exposed at the inner face of the solenoid, should click and retract into the starter housing. The starter solenoid is defective if the pinion gear does not retract.
Why does my muffler pop on my Harley?
Often people think their bike is not tuned properly after the addition of “aftermarket” mufflers because of the additional popping they hear. Stock mufflers provide a lot of volume for the rumbles and popping in the exhaust to be toned down by resonating in the larger muffler canister.
It has been suggested that I bridge the terminals on the solenoid and if all is well the engine should turn over and probably start The likely issue is the battery itself. Although it has voltage, the plates & electrolyte/electrolytic gel have lost their ability to create the needed amperage to push that voltage.
What kind of noise does a Sportster make?
1996 Sportster 1200 Custom, just hit 30,000 miles. First time ever heard ‘pingy’ noise from underneath primary cover, or so it seemed. sort of as if it was (no pun intended) ‘cycling’ along with the engine as the engine is running.
Why does my starter make a clicking sound?
Clicking sound coming from the starter This symptom is common when your battery is low on amps, but is also an indicator that your starter relay is not sending a full signal. The relay is an all or nothing device, meaning that it either sends the full electrical current or sends nothing to the starter.
Where is the starter relay on a Dyna Glide?
Starter solenoid electrical connections. Another component to inspect is the starter relay, which is located in the electrical fuse box underneath the side cover on the left side of the motorcycle. Relays have the potential to go bad and prevent high current from reaching the starter.
What should the voltage be on my starter?
Connect your DMM leads across the battery terminals: You should get between 12.4 and 12.6 volts across the battery terminals with accessories turned off and ambient battery temperature between 60 and 100 F (15 and 37.7 C). If you get a reading below 12.4 volts, your battery is not fully charged.