Why does my GMC Envoy stall in traffic?
I have a 2004 GMC Envoy and came onto the problem of the car stalling when stopped in traffic while in gear. This suddenly happen to my vehicle after I had to changed the battery, although this didnt occur to me until after I solved my problems.
Why does my car idle when the AC is on?
It also helps increase engine speed when an extra load is placed on the engine, for example, when you turn on the AC or defrost system. However, a faulty or restricted IAC valve may keep the engine idle speed from increasing when it needs to.
What to do if your AC is warm while idling?
Your fan should definitely be locked up and providing max air. You can also see if your ac clutch is disengaging at idle. Take a look at it see if it’s turning. If it’s not take something and tap the face of the clutch and see if it pulls in. Of course while you’re doing this be careful and watch for all the moving parts on the engine.
Why is the AC cold in my Chevy Tahoe?
From buying research to owner support, join 1.5 MILLION GM Truck Enthusiasts every month who use GM-Trucks.com as a daily part of their ownership experience. I have a 2001 Chevy Tahoe with the 5.3L engine. I have an odd issue with the AC and was hoping an expert can shed some light on the problem. When the truck is driving, the AC is ice cold.
Why does my GMC Envoy have a rough idle?
While there are a variety of reasons your GMC Envoy has a rough idle, the most common 3 are a vacuum leak, an issue with the spark plugs, or a problem with the ignition coil. See what others are asking about their GMC Envoy. Get answers from RepairPal’s community of auto experts and enthusiasts.
Why does my GMC Envoy die when I Turn Off the a / C?
engine will begin to die when A/C is on and car in or out of gear. I turn off the A/C and it runs fine and if it goes dead it will crank back up with no problem. My 2004 GMC Envoy vibrates when I turn the air conditioner or heater on . It stalls while I’m driving it and it scares me and makes me think that I’m going to break down .
Why does my GMC Envoy stall while driving?
My 2004 GMC Envoy vibrates when I turn the air conditioner or heater on . It stalls while I’m driving it and it scares me and makes me think that I’m going to break down . I just put a brand new battery in and it still stalls .
What was the problem with my 2004 envoy?
2004 Envoy.. When turned on A/C or defrost engine would stall & cut off. I turned off A/C or defrost, cranked & ran fine as long as both were off. Took to shop; had throttle cleaned.
Why is there a shift to Park message on my GMC Acadia?
Plaintiff Marlaina A. Napoli-Bosse says she leased a new 2017 GMC Acadia, but in July 2018 the SUV showed a shift to PARK message as she attempted to shut off the vehicle. The plaintiff says the message shouldn’t have been there because the SUV’s shift lever was in PARK, yet she couldn’t shut off the vehicle.
Why does my GM shift to Park not work?
In addition to losing the ability to shut off and lock the SUVs, owners claim they must resort to all kinds of theatrics to get the SUVs to recognize they are in PARK. Drivers also say the batteries drain and GM has no clue how to fix the issues.
Why does my 5.3 liter Vortec make a ticking noise?
Causes of Startup Noises in a 5.3L Vortec Valve Lifter. Lifter tick is a common occurrence in V-8 engines like the Chevy 5.3-liter Vortec. This ticking sound is caused by the valve lifters, which are filled with oil during engine operation.
What are the symptoms of a Chevy Vortec engine problem?
Symptoms of Failing Idle Control Valve and Throttle Position Sensor 1 Rough idling 2 Engine stalling 3 Hesitation during acceleration 4 Hard shifting and lack of power 5 Lack of accelerator responsiveness 6 P0122 engine code (TPS sensor)
Why is my Chevy Vortec 4300 V6 leaking fuel?
In the L35 and LF6 engines, the spider injectors are known to leak at the pressure regulator and at the supply and return lines due to a design fault. Outside of leaking fuel onto the exterior of the engine itself, it can cause excess fuel to get sucked into the engine.
Where is the temperature sensor on a GMC Envoy 4.2L?
Answer: From the front of the truck, it is located on the passenger side front of the engine. Just below the valve cover. Number 9 above. GMC envoy 4.2L can you tell me where is can find coolant below temperature sensor. There is no such sensor.
Why does my GMC Envoy not have a service light?
Hi, 2004 GMC envoy 4×4 SUV,the service 4WD light came on this morning and hasn’t since. Any thoughts? This a Canadian truck. Would need to know the code it set, but you could be looking at a 4WD switch problem, encoder motor, or possibly a transfer case control module.
Is there a coolant temperature sensor on a Vortec Inline 6?
If what you are saying is true and that the Vortec inline 6 has no coolant temperature sensor then why does auto zone sell one ?Duralast/Coolant Temperature Sensor for your 2004 GMC Truck Envoy 4WD 4.2L SFI DOHC 6cyl. Price: $29.99 Please help me before i spend money.
What is the VIN code for a Chevy Vortec 5.3?
Across both generations the Vortec 5.3 had 10 different engine variations used across the Silverado, Sierra, Suburban, Avalance, Yukon, Tahoe, and a number of other less popular Chevy and GMC vehicles. Vortec 5300 Gen III Engine Codes: LM7 (1999-2007, vin code ‘T’) L59 (2002-2007, vin code ‘Z’)
What are the symptoms of a bad MAP sensor?
A failed MAP sensor has serious implications on fuel control, vehicle tailpipe emissions and fuel economy. Symptoms of a bad or failing MAP sensor include: 1. Excessive fuel consumption A MAP sensor that measures high intake manifold pressure indicates high engine load to the PCM. This results in an increase of fuel being injected into the engine.
Can a bad MAP sensor cause a failed emissions test?
A bad MAP sensor will cause your vehicle to fail an emissions test. Your tailpipe emissions may show a high level of hydrocarbons, high NOx production, low CO2, or a high level of carbon monoxide. A properly trained technician like those at YourMechanic are capable of diagnosing and repairing a failed MAP sensor.
What should the pressure be on a MAP sensor?
At 20 “Hg, the MAP sensor will indicate about 5 psi. This is because the MAP sensor measures “absolute” pressure, based on a perfect vacuum, rather than atmospheric pressure. A failed MAP sensor has serious implications on fuel control, vehicle tailpipe emissions and fuel economy.
I have a 2004 GMC Envoy and came onto the problem of the car stalling when stopped in traffic while in gear. This suddenly happen to my vehicle after I had to changed the battery, although this didnt occur to me until after I solved my problems.
What happens when the MAP sensor goes bad?
When the driver uses the engine to brake, pressure can go as low as 10 in. Hg. Upon accelerating, however, the open throttle body allows air to rush in faster, increasing pressure in the intake. At wide-open throttle, intake and atmospheric pressure are nearly equal. MAP sensor problems could trigger a DTC and check engine light.
What does the MAP sensor read at sea level?
When at rest, the MAP sensor reads atmospheric pressure at sea level (29.93 in. Hg). Because atmospheric pressure varies with weather and altitude, the ECM calculates this “zero” point just before the engine starts, fine-tuning spark and fuel injection mapping from that point.
How is a MAP sensor connected to the intake manifold?
Some MAP sensors are connected to the intake manifold by a hose. Check that the MAP sensor hose is connected and intact. Also, check that the port is free of carbon deposits or other debris, which could block the hose and lead to poor MAP sensor readings. Sensor.
What causes idle surges on a car ECM?
Idle surging can be caused due to other issues in the car, but if it happens in conjunction with other throttle position sensor symptoms, the culprit is often the TPS. At idle, the ECM will not get the correct information and the throttle will variate randomly causing idle surges.
Can a bad throttle position sensor cause idle surging?
Idle surging can be caused due to other issues in the car, but if it happens in conjunction with other throttle position sensor symptoms, the culprit is often the TPS. At idle, the ECM will not get the correct information and the throttle will variate randomly causing idle surges. 3) Check Engine Light
What causes the Check Engine light to turn off at idle?
At idle, the ECM will not get the correct information and the throttle will variate randomly causing idle surges. The check engine light will randomly turn on and off even if the car is running smoothly without any jerks and stalling.
What are the symptoms of a bad coolant temperature sensor?
Hence, it is advised to have your car inspected right away to avoid any serious problems. Here is a more detailed list of the common symptoms of a bad coolant temperature sensor. One of the first symptoms you will notice is that the check engine light will activate.
What happens to the ECT sensor when the coolant is cold?
When the coolant is cold (or ambient temperature), the sensor’s internal resistance is higher. This higher resistance has a direct impact on the 5 Volts passing thru’ it since it blocks some of it from passing thru’ to Ground (-this action of blocking voltage from passing thru’ is called a voltage drop) .
How does the coolant temp sensor work on a PCM?
When the PCM senses this high voltage input, it will translate this voltage input to a coolant temperature of -46° F (-50° C). Coolant temp sensor’s wires have an ‘open-circuit’ problem (usually due to a cut wire).
How to fix a GMC Envoy stall idle problem?
Hope this helps. Also you will need to reset the computer and check engine light, just disconnect the pos post to the battery for ten minutes the reconnect post and turn your ignition key on and off three times to reset the computer and clear codes.
What happens if your coolant temperature sensor goes bad?
Fuel delivery, ignition timing and engine performance are among the key elements affected by the information the coolant temperature sensor gathers. If it goes bad, it can cause several problems. Signs Your Engine Coolant Temperature (ECT) Sensor Is Bad
Where is the coolant temperature sensor located in the engine?
Typically, the coolant temperature sensor is mounted in the engine block or cylinder head, near the thermostat or where the coolant flow is hottest. More than one coolant temperature sensor may be used on some systems to determine the temperature in different locations.
Why does my envoy idle at 600 rpm?
These motors idle at 600 RPM give or take and a worn motor mount will produce a felt vibration at idle that goes away just above idle. If you have never changed the mounts, I would consider that a possibility. Only use AC mounts, the aftermarket is very hit or miss, biased to miss, on damping the 10 Hz frequency at idle.
Why does my envoy have a gasoline smell?
Traced the gasoline smell to a leaking FPR, gasoline smell fixed but rough idle continues. I admit I didn’t check the intake bolts behind the little hose, but none of the other bolts were loose and I sprayed some starter fluid around that area with no change in rpm.
What’s the fuel filter on a Toyota envoy?
Just a pronounced misfire at about 500 rpm. Cleaned TB, run BG44k through tank. Cleaned Camshaft actuator solenoid. Was clean even after 200k, first time I’ve pulled it. Pulled plugs, look fine. Have about 50 k on denso plugs. Changed motor mounts with oem. Air Filter has about 10k on it, fuel filter at about 25k.
Why does my GMC Envoy die at idle?
Took it to them. When the vacuum line is activated for the engine, such as when the air or heat was on, the truck would die at idle (when in gear only, would not die if in neutral). I had changed the battery and on the Envoys it resets all previously stored air/ fuel, idle, etc info that the computer had previously gathered about the motor.
Why does my 2005 Chevy Trailblazer die at idle?
Clean it thoroughly and then take it on a test drive. Once the idle is re-learned, your problem will be solved. Also the radio control **** to turn channels or volume and on and off won’t work the radio and cd will switch back and forth,, what could could cause this — 2005 trailblazer.
What causes a fuel injected engine to stall?
Fuel pressure should be within specifications, when the key is on; then drop 4 to 6 psi once the engine starts. Idle speed on a fuel injected engine is controlled by; allowing a small amount of air to bypass the throttle. The most common failure is partial/complete jamming of the actuator (due to dirt/dust or even oil).
What are the symptoms of an engine stall?
Here are some of the most common symptoms of, a faulty mass airflow (MAF) sensor; The engine is very hard to start or turn over. Engine stalling shortly after starting. The engine hesitates or drags while under load or idle. Hesitation and jerking during acceleration.
What are the signs of a failing ECU?
Common signs of a failing PCM/ECM/ECU include the Check Engine Light coming on, engine performance issues, and the car not starting. 1. Check Engine Light Turns On
What to do if service engine soon does not go off?
If the light does not go off, try buying and installing a new gas cap. They cost less than $10 at your local car parts retailer. It is worth ruling out this common problem before proceeding to bring in the vehicle for an expensive service call. It Wasn’t the Gas Cap? Uh-oh!
Why does my car stall at low rpm?
The will likely force your computer to stall the engine and only allow it to run at low RPMs, which means the car will only move at slow speeds. This is a safety feature enforced by the computer so that your engine doesn’t get too damaged.
What are the problems with a 2004 GMC Envoy?
Top 2004 GMC Envoy Problems 1 Air Compressor for Rear Air Springs May Fail 470 people have reported this 227 2 Fuel Level Sensor Failure 378 people have reported this 214 3 AC Blower Inop Due to Failed Resistor 272 people have reported this 121 4 CD Player In Radio May Fail 175 people have reported this 85
What kind of body does GMC Envoy have?
An Envoy XUV that is equipped with a power-sliding rear roof will also debut for 2004. The four-door Envoy comes in SLE and SLT trim levels. A trapezoidal bodyside shape and a shield-shaped grille help give the Envoy a distinct identity. All three GM models share roofs, tailgates and front doors, but most other body components are unique.
When did the GMC Envoy XL come out?
GMC revived the Envoy name for 2002 on a brand-new midsize model. Its part of a trio of General Motors midsize sport utility vehicles that includes the Chevrolet TrailBlazer and Oldsmobile Bravada. A five-passenger Envoy arrived first. In the spring of 2002, GMC added an extended-length seven-passenger Envoy XL that features three rows of seats.
Is the cab of a GMC Sierra rusted?
Frame cross member behind the cab is rusted through. I have owned vehicles in “salt” states and not had the frame rust out. This should not be considered a “wear item”. This can lead to a failure whereby the fuel tank falls down leading to a high risk of fire.
Is it normal for a car to have rusted undercarriage?
Yep, and it’s also normal for people who don’t live in the salt belt to see the rusty undercarriage and assume it’s a lot worse than it is – – if for no other reason than that a car in the mid Atlantic states that has that kind of undercarriage rust has probably been in a flood or something equally damaging.
Who is the owner of the GMC Envoy?
GENERAL MOTORS, GM, the GM Emblem, GMC, the GMC Truck Emblem and the names ENVOY, and DENALI are registered trademarks of General Motors Corporation. This manual includes the latest information at the time it was printed. We reserve the right to make changes after that time without further notice.
What happens when air conditioner is turned on at idle?
Might want to try this.found bulletin #1878920. Engine stalls when air conditioning is turned on at idle – keywords HVAC rough condition CJ2 CJ3 surge. Engine may stall with the air-conditioner on and or while adding additional loads to the engine at idle.
What causes an engine to stall when the air conditioner is on?
Engine stalls when air conditioning is turned on at idle – keywords HVAC rough condition CJ2 CJ3 surge. Engine may stall with the air-conditioner on and or while adding additional loads to the engine at idle. An example of an addition load would be turning the steering wheel left or right with the air-conditioning on.
What should envoy run temp be when AC is not on?
Overheating when AC is on. Envoy run’s one tick below 210 deg. when AC isn’t on but once it’s on it goes up 3 tick’s above 210 deg. before I started having problem’s last summer it always stayed at 210deg. Had a shop look at it more then once last year and they changed my T Stat to one that I didn’t want.
Might want to try this.found bulletin #1878920. Engine stalls when air conditioning is turned on at idle – keywords HVAC rough condition CJ2 CJ3 surge. Engine may stall with the air-conditioner on and or while adding additional loads to the engine at idle.
Engine stalls when air conditioning is turned on at idle – keywords HVAC rough condition CJ2 CJ3 surge. Engine may stall with the air-conditioner on and or while adding additional loads to the engine at idle. An example of an addition load would be turning the steering wheel left or right with the air-conditioning on.
What causes a GM torque converter to lock up?
Most of the time it is a stuck Torque Converter Clutch (TCC) solenoid, but this is not the only cause of this problem. General Motors has issued a few Technical Service Bulletins (TSBs) relating to this problem. There is also a specific diagnostic procedure to determine the exact cause of the TCC problem.
Can You unplug the solenoid on a GM converter?
Generally, if you unplug the TCC solenoid at the transmission and the symptoms go away, you have found the problem. But sometimes this can be misleading because you don’t know for sure if it’s a bad solenoid, dirt in the valve body or a bad signal from the ECM.