Why does my aftermarket radio not work in my car?
If you plug them into a car with the K-line shorted to +12, they simply won’t work in that car, but it won’t hurt them either. Some dealers will refuse to scan any car that has an aftermarket radio. Since most dealers have “killed” a few of their very expensive scan-tools, I can sort of understand why.
How can I Fix my afterrmarket radio problem?
Do NOT install this resistor in the port. You are simply using it to check and see if the k-line has +12V. If the resistor gets hot, then pull it out and fix the problem by disconnecting the k-line from the stereo’s wiring harness. Remove the radio. Then make the following modification to the car’s wiring harness:
What was the problem with the VW afterrmarket radio?
The problem is, VW brought the “K-Line”, the wire on which all of the control modules in the car communicate with the scan-tool to a pin in the connector on which older radios used to put +12 back into the harness. (We’re not sure whether this was for antenna power or as an amplifier turn-on or what).
Do you need a fuse for an aftermarket radio?
Our other interfaces use output drivers that are thermally protected against shorts. They don’t need a fuse. If you plug them into a car with the K-line shorted to +12, they simply won’t work in that car, but it won’t hurt them either. Some dealers will refuse to scan any car that has an aftermarket radio.
Why does my car radio stop working after I Turn Off the battery?
There are a few different reasons for a car radio to stop working after the battery has gone completely dead. The first, and by far most common, is that the radio has an anti-theft “feature” that kicks in whenever battery power is removed.
What to do if your car won’t start after a radio install?
The previous owner cut the adapter wires to the original radio and had them taped together so I had to wire the new CD player directly to my car and run an ACC wire to the fuse box Well now after I have done this my blinkers don’t work nor do my wipers and my car won’t start. You need to unhook what you did and check for blown fuses.
What to do if your car stereo battery dies?
Car stereos with a code feature require you to input a preset code any time the battery dies or is disconnected. The code may be in your owner’s manual, or you might have to contact a dealer. Electrical system components can be damaged during a jump start if precautions aren’t taken.
What happens when a car radio fuse is blown?
In the case of your car radio fuse, it is designed to sacrifice itself to prevent a dangerous amount of current from flowing through your car radio and the associated circuit. If your radio is dead due to a botched jump start or charge, and you’re lucky, then you may find that your car radio fuse is blown.
Why does my pioneer stereo not produce any sound?
At this point, the stereo doesn’t send any signal to the speakers. The unit powers on and reads CD’s just fine, but refuses to make any kind of sound. Any ideas? Answered! View the answer I have this problem too
Is there a problem with the afterrmarket radio?
You can test for this problem yourself without removing the radio. First, if your car is a 1996 or earlier model, don’t bother — the K-Line doesn’t go to the radio harness and there is no possibility that that the car has this problem. If you have a Vag-Saver : Simply turn the ignition ON and plug in the Vag-Saver.
What do you call an aftermarket car stereo?
These stereos are called OEM replacements. Sound systems that have Bluetooth are made for hands-free use. This allows a driver or passenger to pair their Bluetooth devices like a smartphone to the car stereo to manage calls and music. The stereos come with an external microphone and play the sound with the car speakers.
Can you install an aftermarket audio system on your own?
Yes, it is quite possible to install an aftermarket car audio system on your own. It’s not that difficult to manage without professional help. That said, the installation process varies based on what type of stereo you will be using. If you are going to use a single DIN car stereo, it won’t take that long.
Can a double DIN stereo be replaced in an aftermarket car?
OEM Replacement: Some cars inconveniently do not allow a single or double DIN system to replace the OEM system and need an aftermarket stereo that is designed in a size to accommodate your car’s dash like the OEM stereo. These stereos are called OEM replacements. Sound systems that have Bluetooth are made for hands-free use.
Where to connect the radio’s ground wire?
There was NO ground wire on the Mitsubishi wiring harness, so when I installed the radio, I connected it to the DASH LIGHT line in the wiring harness. [Cue the Stump-the-Chumps correct answer sound!] I will rewire this to fix it. Can anyone suggest where to connect the radio’s ground wire?
Is there a problem with the afterrmarket radio harness?
First, if your car is a 1996 or earlier model, don’t bother — the K-Line doesn’t go to the radio harness and there is no possibility that that the car has this problem. If you have a Vag-Saver : Simply turn the ignition ON and plug in the Vag-Saver. Look at the LED. Green is OK, Red is not OK.
Why is the radio not working on my Street Glide?
I replaced the battery on my wife’s 2010 Street Glide. Now the radio won’t come on. Any suggestions would be appreciated. A: If you have no power to your radio, check for a blown fuse 1st.
What can I do about my radio not working?
I have 09 Ultra Classic speakers on and off , now won’t come on everything else works when head set is plugged . Anything I can do to fix ? You can try a radio diagnostic. Eject CD, if installed. Press & hold two soft keys (any two buttons 1 thru 6). Keep holding the two down while switching on the ignition switch.
What happens when the radio and lights don’t work?
But when a car owner attempts to turn on the engine and the attempt fails, yet the radio and lights still work, it can lead to confusion. This is particularly true among motorists who aren’t very well-versed in the issues that can occur with vehicles that could lead to such problems.
What to do when your car wont start but the radio and lights work?
If you have a manual car and it won’t turn on, it could be because you don’t have the clutch pressed in far enough. Adjust the clutch to make sure that it is pushed in all the way and try starting the car again. When a car won’t start but the radio and lights still function, it can be frustrating.
Why is my Chevy TheftLock radio not working?
The radio display will read “LOC” and the device will not turn on. Whenever your Chevy battery is disconnected or the battery dies, the Delco Theftlock radio enters the “LOC” mode. Follow these steps and you can reset the anti-theft radio and return the radio to a working state.
How do you put a three digit code on a car radio?
Step 1: Start the vehicle and turn on the radio. Step 2: Press and hold preset numbers 2 and 3 until a three digit code appears on the radio display. Write this code down. Step 3: Press the AM/FM button. Your radio will display a second three digit code.