Why do the lights go off on my Honda Odyssey?
I recently started having this trouble with my 2002 odyssey. The TCS and ABS lights come on and go away intermittently. I took it to the honda dealership and they ran the initial tests and basically cleared the lights. I drove it home no lights, once parked I shut off the engine, restarted it and the lights came back on.
What are the problems with a 2012 Honda Odyssey?
See all problems of the 2012 Honda Odyssey . Brand new car 2017 Honda Odyssey with less than 300 miles driving on a winding road uphill and the check engine light starts flashing. Manual advises to pull over to turn off and let the car cool down. Did that and then the vehicle stability assist light also goes on.
What does the VSA symbol mean on Honda Odyssey?
While driving during rush hour traffic the vehicle suddenly without warning began to apply the brakes and the engine idled down then temporarily seemed normal only to have it reoccur in a matter of seconds. The vsa light including the symbol and the initials vsa became illuminated.
How to reset ABS and TCS lights in Honda Odyssey?
Check ground or a short between PCM and ABS/TCS control unit. Check for loose connectors at the PCM. Check the PCM. Check for loose connectors at the ABS/TCS control unit. Check the ABS/TCS contol unit. I checked the fuse box under the hood and replaced the blown fuse #50 (30A) and reset the lights.
I recently started having this trouble with my 2002 odyssey. The TCS and ABS lights come on and go away intermittently. I took it to the honda dealership and they ran the initial tests and basically cleared the lights. I drove it home no lights, once parked I shut off the engine, restarted it and the lights came back on.
Where are the fuses on a Honda Odyssey?
Check Fuse # 50 (30A) in the Under-hood Fuse/Relay Box. Check ground in the motor power circuit. Check Fuse # 14 (7.5A) in the Passenger’s Under-dash Fuse/Relay Box. Check ground and a loose connection in the Under-dash Fuse/Relay Box and the ABS Control Unit. Check ground in the MCK circuit. Check pump motor relay in the Under-hood ABS Relay Box.
Check ground or a short between PCM and ABS/TCS control unit. Check for loose connectors at the PCM. Check the PCM. Check for loose connectors at the ABS/TCS control unit. Check the ABS/TCS contol unit. I checked the fuse box under the hood and replaced the blown fuse #50 (30A) and reset the lights.
What to do if your Honda Odyssey has a malfunction?
The location of the malfunction is indicated by the warning lamp flashing. 1. Drive vehicle over 30 km/h (19 MPH) for at least one minute. 2. Turn ignition switch OFF. 3. Ground terminal 9 of Data Link Connector with a suitable harness. 4. Turn ignition switch ON while grounding terminal 9.
Check Fuse # 50 (30A) in the Under-hood Fuse/Relay Box. Check ground in the motor power circuit. Check Fuse # 14 (7.5A) in the Passenger’s Under-dash Fuse/Relay Box. Check ground and a loose connection in the Under-dash Fuse/Relay Box and the ABS Control Unit. Check ground in the MCK circuit. Check pump motor relay in the Under-hood ABS Relay Box.
The location of the malfunction is indicated by the warning lamp flashing. 1. Drive vehicle over 30 km/h (19 MPH) for at least one minute. 2. Turn ignition switch OFF. 3. Ground terminal 9 of Data Link Connector with a suitable harness. 4. Turn ignition switch ON while grounding terminal 9.
Where is self diagnostic results Terminal on Honda Odyssey?
To start the self diagnostic results mode, ground the self-diagnostic (check) terminal located on Data Link Connector. The location of the malfunction is indicated by the warning lamp flashing. 1. Drive vehicle over 30 km/h (19 MPH) for at least one minute. 2. Turn ignition switch OFF. 3.
How do you reset the ABS light on a Honda Odyssey?
1. Drive vehicle over 30 km/h (19 MPH) for at least one minute. 2. Turn ignition switch OFF. 3. Ground terminal 9 of Data Link Connector with a suitable harness. 4. Turn ignition switch ON while grounding terminal 9. Do not depress brake pedal. 5. After 3.0 seconds, the warning lamp starts flashing to indicate the malfunction code No. (See NOTE.)
How to reset the SRS light on a Honda Odyssey?
I had to search numerous posts before figuring out everything needed to reset the SRS light on my 2002 Odyssey. I thought it might be helpful to someone else to summarize all that I found in one post… 1. Locate the yellow 2-pin MES Connector on the fuse block above the driver’s kickpanel (two blue wires).
1. Drive vehicle over 30 km/h (19 MPH) for at least one minute. 2. Turn ignition switch OFF. 3. Ground terminal 9 of Data Link Connector with a suitable harness. 4. Turn ignition switch ON while grounding terminal 9. Do not depress brake pedal. 5. After 3.0 seconds, the warning lamp starts flashing to indicate the malfunction code No. (See NOTE.)
What does it mean when SRS light is on Honda Odyssey?
It sets off a sensor when an object is placed in the seat. My Honda SRS light comes on when I place something in the passenger seat without clicking on the passenger side seat belt. It sets off a sensor when an object is placed in the seat. The SRS light referes to the supplemental restraint system. This involves your airbags.
Where is the fuse block on a 2002 Honda Odyssey?
On my 2002 Ody EX-L, the connector appears to be ‘plugged into’ the fuse block. Once you release it, you’ll notice there are no pins in the ‘socket’, so its not really a socket, but stowage for the connector.
When to reset the Check Engine light on Honda Civic?
Continue reading to learn how to reset this light and save yourself the dealership cost. This article applies to the Honda Civic (1992-2000), and Accord (1990-2002). The check engine light in your Honda offers important diagnostic information, which will alert you of a serious problem like a bad catalytic converter.
What is the code for the Honda check engine light?
A long flash (or approximately one second) equals 10. A short code (or approximately half a second) equals one. For example, two long flashes followed by two short flashes will equal to the code 22. Any subsequent codes will follow in 2.5 second intervals.