Why are the turn signals on my Harley not working?
2) If you have LED type bulbs, someone replaced the turnsignals BEFORE you and may not have added the recommended load equilizer (simulates load of filament type bulbs), and never got the problem fixed just right, and if left alone it can “fry” the TSM/TSSM. Hopefully you have not gotton to this point and have to replace the module.
What are the turnsignals on a Harley Davidson?
1) Turnsignals all stock means the front signal lights one of the two filaments in the front; the rear signal lights use single filiament lights.
Why is my hazard light not working on my Harley?
Check the hazard light box and make sure all signal wires are attached. Check the flasher for functionality (turn signal relay). The wiring for the turn signal lights goes through the turn signal switch. This means that the turn signal switch may be bad. If only one light (or one side) isn’t working, check the power to the bulb plug-in connections.
Is it illegal to not have a turn signal on a bike?
It’s not a showstopper because you can still ride. But turn signals are an essential part of bike safety. Hand signals are fine during the day, yet are hard to see at night. A broken signal light is illegal in many states. So, don’t let this problem persist. Get those signals fixed as soon as you can.
Why do my turn signals stop flashing when I apply the brake?
Make sure you have the right bulbs in and check the wiring harness on your lights and take a look inside the light assembly for any short circuit. Also any addition like the third brake light and, like mayer said, a trailer light plug that is shortened can do it too. Good Luck to you Was this answer helpful?
How is the hazard light connected to the turn signal?
The brake light circuit and the turn signal circuit have crossed paths somewhere. The wires carrying the power supply from the turn signal switch is connected or touching the brake wires. The hazard light button is essentially an additional power source and switch for the turn signal circuit.
How to reset the turn signal on a Harley Davidson Dyna Glide?
Press the reset button again and the display will read “PSSPt.” Press the reset button a few times until the first “S” is flashing, then press and hold it for five seconds. The error codes should now display on the odometer. Press and hold the odometer reset button for five seconds to clear each code.
Where does the flasher go on a Harley Davidson?
Check the flasher for functionality (turn signal relay). The wiring for the turn signal lights goes through the turn signal switch. This means that the turn signal switch may be bad.
Why are the turn signals on my Harley Davidson not working?
I’m not getting any power to the right side turn signals, the green arrow on the dash don’t light up on right, and turn signals are very dim and slow on left side. Wiring seems to check out, fuses ok.
Why is my turn signal not working on my FXDX?
My ’99 FXDX used to rub the wire under the rear guard to give the same symtoms. Every so often it would rub through the insulation. Usually after riding with a pillion and after a big bump in the road. Didn’t matter how well it was clipped up and insulated (spiro-tie, heatshrink etc) after six months or so it would do it again.
Check the hazard light box and make sure all signal wires are attached. Check the flasher for functionality (turn signal relay). The wiring for the turn signal lights goes through the turn signal switch. This means that the turn signal switch may be bad. If only one light (or one side) isn’t working, check the power to the bulb plug-in connections.
How do you reset the turn signal on a Dyna Glide?
Press left turn signal switch once, and light will flash a number of times to indicate an error code. There is 1.5 seconds between flashes to indicate 1st and 2nd digit of codes and four second pause between codes. Press and hold left switch down for five seconds, and light will flash twice to indicate the TSSM is reset. Turn ignition to off.
What should I do if my turn signal light is not working?
LED lights rarely fail. The first test that you should perform is to disconnect the LED turn signal light and apply power to the LED bulb. Does the LED light turn on? If the LED doesn’t turn on, replace it. If the LED turn signal light does turn on, the LED light is not the problem.
Do you need to replace the turn signal switch?
Take a look at the part inside the turn signal/combination switch that often fails. You can’t replace the internal part, therefore, the whole turn signal switch needs to be replaced. Click here to check prices on new & used Mercedes turn signal switches. Replace the turn signal switch.
2) If you have LED type bulbs, someone replaced the turnsignals BEFORE you and may not have added the recommended load equilizer (simulates load of filament type bulbs), and never got the problem fixed just right, and if left alone it can “fry” the TSM/TSSM. Hopefully you have not gotton to this point and have to replace the module.
Why does my rear turn signal not flash?
Rear signals are still hooked up but don’t flash.. yes, bsmith. most likely they don’t work because they aren’t hooked up , up front. ypu can wire a resistor inline to remedy that. yes, bsmith. most likely they don’t work because they aren’t hooked up , up front. ypu can wire a resistor inline to remedy that.
1) Turnsignals all stock means the front signal lights one of the two filaments in the front; the rear signal lights use single filiament lights.
Check the flasher for functionality (turn signal relay). The wiring for the turn signal lights goes through the turn signal switch. This means that the turn signal switch may be bad.
Why does my turn signal Flasher not work?
Flashers work but turn signals don’t. There may not be enough amperage going through the system load equalizer to activate the flasher. Go ahead and replace the bulbs with hotter ones that draw more amperage. A turn signal flasher is like a circuit breaker that trips under a load and automatically resets (flashes).
How many bulbs are in a turn signal Flasher?
Go ahead and replace the bulbs with hotter ones that draw more amperage. A turn signal flasher is like a circuit breaker that trips under a load and automatically resets (flashes). Each side (left and right) turn signal is two bulbs (minimal load) and four bulbs for the emergency flasher (maximum load).
What to do when your turn signal doesn’t work?
Turn the ignition to run/stop in run position with ignition off. Hold ODO reset button in and hold. Turn ignition switch to IGN. Release ODO reset button. Background should light up, speedometer needle should sweep its full range and indicator lamps (battery, security, low fuel, check engine and cruise) should all light up.
How to diagnose turn signals dont work properly?
Some vehicles use a solid state flasher module that contains transistors and diodes. On these vehicles, you should consult a vehicle specific service manual for proper diagnosis. You should always use a replacement bulb of the same part number as the one being replaced.
What happens when a turn signal Flasher fails?
Step 3 – When a turn signal flasher or relay fails the blinkers will not operate or come “ON”, but not blink. A direction signal system is designed to operate with a flasher or blinker unit which interrupts the signal which created the blinking action. Learn more-Locate turn signal flasher in Google Images.
Why is my turn signal not working on my Harley?
You may have a bad module or corroded/bad connections at the module or at the handlebar switch harness/ plug. If you determine that you need a turn signal module, we suggest Badlands. I have 2005 Road king Classic, the alarm light is coming while riding and the fob is not being touched to arm or disarm the alarm.
Why is my blinker not working on my Turn signal?
A direction signal system is designed to operate with a flasher or blinker unit which interrupts the signal which created the blinking action. Learn more – Locate turn signal flasher in Google Images. Step 4 – When a turn signal switch fails the system will short or go “open” causing the blinker not to operate.
Why is my left turn signal not flashing?
When it’s not working, there is no signal front & rear and no signal indicator either. When working, both markers function properly as does the indicator. With new bulbs installed and sockets cleaned, I’ve narrowed the problem down to either the left turn signal switch or the turn signal module.
Why are the turn signals on my hog not flashing?
Find the orange wire that feeds 12 volts to your turn signal module. Power it off of a breaker that is powered on, both 1 & 2 “clicks”. My speedometer is working erratic. When I give it throttle the speedimeter digital reading goes blank and the engine light comes on and the turn signals will not flash. When I come to a stop they work
Find the orange wire that feeds 12 volts to your turn signal module. Power it off of a breaker that is powered on, both 1 & 2 “clicks”. My speedometer is working erratic. When I give it throttle the speedimeter digital reading goes blank and the engine light comes on and the turn signals will not flash. When I come to a stop they work
When it’s not working, there is no signal front & rear and no signal indicator either. When working, both markers function properly as does the indicator. With new bulbs installed and sockets cleaned, I’ve narrowed the problem down to either the left turn signal switch or the turn signal module.