Why are the turn signals on my Harley Davidson not working?

I’m not getting any power to the right side turn signals, the green arrow on the dash don’t light up on right, and turn signals are very dim and slow on left side. Wiring seems to check out, fuses ok.

What to do if your turn signal is bad?

2) Is the battery and bike on fairly regular maintenance schedule (on a battery tender when stored for over a week), garaged, and ran fine say the day before, etc. 3) Did you add modifications to the handlebar controls or service wiring or bar on either side’ hand control groups?

Why is my turn signal not working on my FXDX?

My ’99 FXDX used to rub the wire under the rear guard to give the same symtoms. Every so often it would rub through the insulation. Usually after riding with a pillion and after a big bump in the road. Didn’t matter how well it was clipped up and insulated (spiro-tie, heatshrink etc) after six months or so it would do it again.

Why do the tail lights work but not the turn signal?

The tail lights work but not the turn signal. The left front flashes rapidly and the right side signals work so I figure it’s not the flasher unit. is there something else I should be considering? *#&! electrical problems! Could be a broken wire going to the brake light switch . Since the brake

Why is the left side of the turn signal not working?

This time, though, the left or right side of the signals doesn’t work. You may see the dash indicator lamps illuminating brightly, but the turn lights won’t flash. You may be dealing with bad bulbs or a fault between that side of the circuit and the turn signal switch itself.

What to do if your turn signal switch is bad?

You may be dealing with bad bulbs or a fault between that side of the circuit and the turn signal switch itself. First, check the bulbs to see if they are still in good shape: No darkened areas or damaged filaments. Then, check the sockets for corrosion, wear or damage. Confirm the ground and power connections are working properly.

What makes a car have a turn signal problem?

Most common problem sources include bulbs, wires, connectors, fuses, flasher units, and switches. So the average car owner can troubleshoot these faults with the use of a test light and, sometimes, a digital multimeter (DMM).

What causes a Harley Davidson brake light to burn out?

While this may seem like only a maintenance issue, some Harley’s bulbs have been installed improperly. Bulb burnout exposes a rider safety problem resulting from signals and brake lights malfunctioning. It’s risky enough to be a motorcycle rider without the risk of bulb burnout.

Are there rear running lights on a Harley?

You don’t say anything about year but unless something has changed, rear turn signals on Harley’s have never been running lights unless you add the kit to make them so. Can’t figure it out. Brake light works, rear turns work, but no rear running lights.

How does the turn signal work on a Dyna Glide?

This article applies to the Harley Davidson Dyna Glide. There are many modules on your Harley Davidson that track as well as monitor the state of your powertrain and accessories. The Turn Signal Security Module monitors the signals and the alarm system for the bike. When there is a problem, the red light key will illuminate.

Is there a recall on the 2006 Harley Davidson Dyna?

Owners of 2006 Harley-Davidson Dyna motorcycles, such as the Dyna Wide Glide, will just have to disregard the neutral light’s indication until the recall maintenance has been performed.

How do you reset the turn signal on a Dyna Glide?

Press left turn signal switch once, and light will flash a number of times to indicate an error code. There is 1.5 seconds between flashes to indicate 1st and 2nd digit of codes and four second pause between codes. Press and hold left switch down for five seconds, and light will flash twice to indicate the TSSM is reset. Turn ignition to off.

Why is my hazard light not working on my Harley?

Check the hazard light box and make sure all signal wires are attached. Check the flasher for functionality (turn signal relay). The wiring for the turn signal lights goes through the turn signal switch. This means that the turn signal switch may be bad. If only one light (or one side) isn’t working, check the power to the bulb plug-in connections.

Why are my turn signal lights not blinking?

Both rear signal lights don’t blink at all and the turn indicator on my dash display doesn’t also blink ( the small green circle signal indicator on the dash ) No matter if I turn the switch left or right, both turn lights on the front blink together. What could be wrong? where would the damage be? Posts: A lot.

Why is the blinker on my Harley Davidson not working?

If only one light (or one side) isn’t working, check the power to the bulb plug-in connections. With a voltmeter or test light, check the terminals for power. Check the battery for a full charge. Figure 1. Multimeter. Also consider what kind of work was recently done on the bike that might have affected the blinker system.

How does the turn signal on a Harley Davidson work?

The Turn Signal Security Module monitors the signals and the alarm system for the bike. When there is a problem, the red light key will illuminate. Diagnosing and clearing the codes on each module is really simple, as explained below.

Why does my bike turn signal not flash?

If the bike is not moving the right turn signal functions correctly. If bike is moving, if you press the right turn signal, it will light up, but not flash. Looked in the service manual and this problem is not listed for troubleshooting the turn signals. Any suggestions? Hi, Mike. Would try the signal function without the Badlands module.

Why does my Harley Davidson have no power?

Last Friday I shut the motor off with the stop switch and then turned the ignition key off. I re-set the stop switch to On. 1 minute later, I turned the ignition switch to ignition and noticed I had no power to my headlights and instrument lights.

Is there a problem with my Sportster 1200 XLH?

Before I go out and buy parts I think I need, maybe somebody can jump in and pinpoint the problem. 1995 Sportster 1200 XLH. Ride it daily to work. Last Friday I shut the motor off with the stop switch and then turned the ignition key off.

Why is my turn signal not working on my Harley?

You may have a bad module or corroded/bad connections at the module or at the handlebar switch harness/ plug. If you determine that you need a turn signal module, we suggest Badlands. I have 2005 Road king Classic, the alarm light is coming while riding and the fob is not being touched to arm or disarm the alarm.

Why does my turn signal on my Dyna not flash?

I have a ’94 dyna wide glide and whenever I use the turn signals they do not flash, if I hit the right signal it just lights up soild and does not flash and that goes for the left side as well. I went to the dealer and asked what would cause this problem my first guess was a relay but the dealer said it was most likely the turn signal module.

What should I do if my turn signal light is not working?

LED lights rarely fail. The first test that you should perform is to disconnect the LED turn signal light and apply power to the LED bulb. Does the LED light turn on? If the LED doesn’t turn on, replace it. If the LED turn signal light does turn on, the LED light is not the problem.

Do you need to replace the turn signal switch?

Take a look at the part inside the turn signal/combination switch that often fails. You can’t replace the internal part, therefore, the whole turn signal switch needs to be replaced. Click here to check prices on new & used Mercedes turn signal switches. Replace the turn signal switch.

What does it mean when your turn signal is not working on Mercedes?

In newer Mercedes models, you will get a warning on instrument cluster stating “Turn Signal Left / Right / Front / Rear / Side Malfunction”. Depending on the Mercedes model and problem a warning may or may not show on the dashboard.

What to do if left turn signal is not working?

If you don’t have a manual, then have a look at the TS module and hopefully the pins are labled. If you apply 12 vdc to the (Lt out) pin -the Left turn signal lights should come on. (you’ve just bypassed the TSM) Next.. connect a jumper from (Lt in)pin to (Lt out) pin & press the Left turn signal switch.

How do you reset the turn signal on a Harley Davidson?

Press left turn signal switch twice, pause, and lights will flash. Press right turn signal switch once, pause, and lights will flash. Press right turn signal switch once, pause, and lights will flash twice. Press right turn signal switch once, pause, and lights will flash three times.

Why is my turn signal on my Harley Davidson not flashing?

A cheap easy fix ! could be wrong but i belive this can alos be caused from bad connection or problem with wireing to signal itself. after i wired my rear fender my left signal stopped flashing. investigated and a clip broke loose under my fender and wiring for left side was hitting on the tire. wire got a little chewed up. replaced it. good to go.

Where are the signals on a Harley Davidson Road King?

Road King models (FLHR) have their harness hidden in the headlight shell, while larger Touring models often secure the wiring harness in the front fairing. Once you have located the harness, trace the wiring from the original turn signals back to the harness to locate each signal’s connectors.

Where does the flasher go on a Harley Davidson?

Check the flasher for functionality (turn signal relay). The wiring for the turn signal lights goes through the turn signal switch. This means that the turn signal switch may be bad.

Where is the bank angle sensor on a Harley Davidson?

On some bikes it’s called a Bank Angle Sensor (BAS) and is located in the Turn Signal Security Module (TSM or TSSM). Check and clean your speed sensor. It may seem irrelevant but the TSSM serves many functions. Timing for turn signals is picked up by the speed sensor to control the time out distance/time.

Is it illegal to not have a turn signal on a bike?

It’s not a showstopper because you can still ride. But turn signals are an essential part of bike safety. Hand signals are fine during the day, yet are hard to see at night. A broken signal light is illegal in many states. So, don’t let this problem persist. Get those signals fixed as soon as you can.

Why does my turn signal light up but not flash?

Before you spend any money, check all the bulbs. If one bulb on the right side, say the rear bulb, is burned out, the front bulb will light up, but won’t flash. You might have a bulb burnt out on each side. I’ve seen stranger things.

When do turn signals flash, bike won’t start?

Re: Turn signals flash, bike won’t start, no key fob with… If you turn signal flashing,then your security system is on. You will need the key fob for starting.,or change the Bat on Key Fob. You can’t post conmments that contain an email address.

Why is the head light not flashing on my Harley Davidson?

No head light, and no tail light. After spending several hours goint through the wiring looking for a short, we discovered that both head light and tail light we burned out. Good luck. I {Heart} Hookers. If the bulbs are lighting, but not flashing, then it’s the relay or the turnsignal module.

Why are my turn signals not flashing on my Harley Davidson?

If you are stuck with having to manually cancel the turn signals, the problem could be found in connectivity to the speedometer or the TSSM. Check the switches. Check for loose or disconnected wires to the speedometer. Check the tip switch that cancels if the bike falls over.

Why is the right turn signal light not working?

The right turn signal light and the neutral light does not light. What do you call these indicators lights and where can you get them? Hi William. Those are, simply, indicator lights. They are sealed. There are no bulbs to change for the indicators on your year/model. Usually, when one fails, however, it is due to a bad connection or switch.

What to do when your turn signal doesn’t work?

Turn the ignition to run/stop in run position with ignition off. Hold ODO reset button in and hold. Turn ignition switch to IGN. Release ODO reset button. Background should light up, speedometer needle should sweep its full range and indicator lamps (battery, security, low fuel, check engine and cruise) should all light up.

Check the flasher for functionality (turn signal relay). The wiring for the turn signal lights goes through the turn signal switch. This means that the turn signal switch may be bad.

Why is my left turn signal not flashing?

When it’s not working, there is no signal front & rear and no signal indicator either. When working, both markers function properly as does the indicator. With new bulbs installed and sockets cleaned, I’ve narrowed the problem down to either the left turn signal switch or the turn signal module.

Why is my turn signal not flashing on my Fatboy?

Had the same problem on a 99 Fatboy changed the ignition switch and problem was solved Have a 97 FXDWG. Installed a badlander load equalizer 17 years ago for run and brake lights on the rear. If the bike is not moving the right turn signal functions correctly.

What are the turnsignals on a Harley Davidson?

1) Turnsignals all stock means the front signal lights one of the two filaments in the front; the rear signal lights use single filiament lights.

What does the brake light mean on a Harley Davidson?

What that means is the fronts have “running light filiament AND a signal filiament”, the backs have a single filiament that only has a single turnsignal filiament, with the brake light coming on when you hit the brakes.

What kind of lighting does a Harley Davidson use?

CorkyShark, welcome to HDTimeline and your first troubleshooting “exercise”. What others are trying to say is you need to determine if the turnsignal lighting is filament type (stock) or LED type (aftermarket).

Why are the turn signals on my hog not flashing?

Find the orange wire that feeds 12 volts to your turn signal module. Power it off of a breaker that is powered on, both 1 & 2 “clicks”. My speedometer is working erratic. When I give it throttle the speedimeter digital reading goes blank and the engine light comes on and the turn signals will not flash. When I come to a stop they work

Why is my left turn signal not working?

I have 2005 Road king Classic, the alarm light is coming while riding and the fob is not being touched to arm or disarm the alarm. The light comes on for the alarm and stays on while riding and at that time my right turn signal stops working, the left one still works fine.

How to turn off the FOB on a Harley Davidson?

Here’s how to do it!! 1. Select 5 digit code ( each digit being a 1 thru 9) and record it on the wallet card in the owners manual. 2. With an assigned FOB present, turn IGN key ON – OFF – ON – OFF – ON 3. Press Left turn signal switch 2 times. 4. Press Right turn signal switch one time and release.

What are the features of a black Harley Davidson Night Train?

Harley riders have always had a special place in their heart for the color black. The black-on-black Night Train® model has a profile that pushes the limit. Sink deep into the depths of its low custom seat. Settle in behind the stainless drag bars on top of six-inch risers, and a wide raked fork straddling a 21-inch laced wheel.

How do you turn off lights on a bike?

This method should work with all bikes built after 2001. Move kill switch to off position, turn ignition on-off-on-off-on. Press left turn signal switch twice, pause, and lights will flash. Press right turn signal switch once, pause, and lights will flash. Press right turn signal switch once, pause, and lights will flash twice.

Why does my rear turn signal not flash?

Rear signals are still hooked up but don’t flash.. yes, bsmith. most likely they don’t work because they aren’t hooked up , up front. ypu can wire a resistor inline to remedy that. yes, bsmith. most likely they don’t work because they aren’t hooked up , up front. ypu can wire a resistor inline to remedy that.

Why is my Harley Davidson Softail not working?

These systems must stay properly powered by the battery. The wiring connecting the systems together must remain intact. These problems occur and, although difficult to find at times, a series of test will help you narrow down the cause. This article applies to the Harley Davidson Softail.

Why are my turn signal lights not flashing?

My Harley Heritage Softail 1996 indicator/turn signal lights stay on when instead of blinking. I hit the “turn” button for the signal/turn lights, but they just come on and stay on!

How does the turn signal work on a Harley Davidson?

Timing for turn signals is picked up by the speed sensor to control the time out distance/time. The speed sensor feeds the speedometer through the TSSM and also the ECM for controlling fuel flow to the injectors. If you need to reset your TSSM security module, refer to Step 5 for instructions.

My Harley Heritage Softail 1996 indicator/turn signal lights stay on when instead of blinking. I hit the “turn” button for the signal/turn lights, but they just come on and stay on!

When do I use the turn signals, both tail lights blink like hazard lights?

Q: When I use the turn signals, both tail lights blink like hazard lights. Hello! I need help with a tail light problem. This morning I got pulled over and given a warning about one of my brake lights not turning on when I use the brake, so I got home and fixed it doing some rewiring. It worked. Until I noticed the right side didn’t work.

What happens when a turn signal Flasher fails?

Step 3 – When a turn signal flasher or relay fails the blinkers will not operate or come “ON”, but not blink. A direction signal system is designed to operate with a flasher or blinker unit which interrupts the signal which created the blinking action. Learn more-Locate turn signal flasher in Google Images.

What happens when a turn signal goes bad?

Turn signals on either side of the vehicle can be wired in series, much like the bulbs on a strand of Christmas tree lights. If one goes bad, or it isn’t properly grounded, it can affect the corresponding light on the same side. Check for damaged or burned-out bulbs in all turn signals on that side.

How can I Fix my Turn signal problem?

Step 1 – Turn the ignition key to the “ON” position, (do not start the engine) this will power up the electrical system for testing. Step 2 – Locate the power distribution center (PDC) or fuse panel to check all system fuses. Learn more – To locate the fuse consult the owner’s manual or search Google Images.

Where is the turn signal module on a Street Glide?

Jonathan, sounds like you have a bad turn signal module. You will find this module between the fuel tanks, beneath your dash area. Thanks, and good luck Similar Question Been enjoying the videos and tips I have a 2008 Street glide with 90K miles on it. I always took it to the dealer until I found your website and got the premium membership.

Why is my Harley Davidson Ultra Classic not starting?

I have a 2010 ultra classic with ABS. It is not starting. The battery voltage is 12.75 off the battery. When I turn the main switch on, I get a drop to 12.5, and when the kill switch is turned on, I get a drop to 12.38. The self test goes out and hit the start switch with nothing – no volt drop, no starter engage, no nothing. DEAD.

Can a broken turn signal on a Harley Davidson be fixed?

This article applies to the Harley Davidson Touring. A busted or erratic turn signal repair can be a drag to fix, especially on the road. It’s not a showstopper because you can still ride. But turn signals are an essential part of bike safety. Hand signals are fine during the day, yet are hard to see at night.

Why does the left side turn signal work?

The left front flashes rapidly and the right side signals work so I figure it’s not the flasher unit. is there something else I should be considering? *#&! electrical problems!

How do you turn off the ignition on a Harley Davidson?

Turn the ignition switch on-off-on-off-on quickly. With a proximity fob system, press the left turn signal switch three times and the right turn signal switch once. The blinkers will flash and the PIN should appear in the odometer window.

What to do if your turn signal doesn’t cancel?

If your turn signal doesn’t cancel one way or the other after turning a corner, a turn signal spring is probably broken and needs replaced. Loading…

Why is my turn signal not working on my Road King?

Im going through the same thing right now with my 15 road king, I ordered a new harness got it plugged it in now neutral light comes on with switch turned off or on, everyone said change wiring harness mine signals work but lt turn and high beam don’t, Help Schmiddty? Click to expand… I haven’t run into this problem yet.

What does it mean when your turn signal is too slow?

Fast or Slow Flashing. If your turn signal flashes too fast or too slow, it’s a problem with the heat rate transfer through the flasher strip. Most often, if all four turn signals are going too fast or too slow, it means the flasher is bad. If only the signals on one side do it, it may be one of the bulbs.

Navigation