Where is the speed sensor on a Mitsubishi Eclipse?
The vehicle speed sensor on the Mitsubishi Eclipse is located on the transmission–in most years, just behind the shift linkage. The computer supplies 5 volts to the speed sensor.
Where is the speed sensor on a car?
Open the hood. Locate the vehicle speed sensor on the side of the transmission, near the shift linkage. Unplug the sensor by pulling the tangs on either side of the plug away from the connector, then pull the connector off the plug. Unbolt the speed sensor, using the appropriate socket.
How do you unbolt a speed sensor?
Unplug the sensor by pulling the tangs on either side of the plug away from the connector, then pull the connector off the plug. Unbolt the speed sensor, using the appropriate socket. Install the new sensor and tighten the bolt firmly. Plug in the sensor, ensuring that the connector snaps into place.
The vehicle speed sensor on the Mitsubishi Eclipse is located on the transmission–in most years, just behind the shift linkage. The computer supplies 5 volts to the speed sensor.
Open the hood. Locate the vehicle speed sensor on the side of the transmission, near the shift linkage. Unplug the sensor by pulling the tangs on either side of the plug away from the connector, then pull the connector off the plug. Unbolt the speed sensor, using the appropriate socket.
Unplug the sensor by pulling the tangs on either side of the plug away from the connector, then pull the connector off the plug. Unbolt the speed sensor, using the appropriate socket. Install the new sensor and tighten the bolt firmly. Plug in the sensor, ensuring that the connector snaps into place.
How many miles does a Mitsubishi Eclipse GST have?
I have a Mitsubishi Eclipse turbo GST 1997 with only 121,000 miles on it. 2.0 turbo has 210 horse power. This is a stick shift 5 speed. Adult owned not abused. Low miles for 19 year old car.
Is there a 1996 Mitsubishi Eclipse GST for sale?
I have for sale a 1996 Mitsubishi Eclipse GST with manual transmission and turbocharged 2.0L 4 cylinder engine. This car has a little under 93,000 miles. It has new brake pads in the front, the back are almost brand new. I just put a new tie rod on the front left.
What kind of engine does an eclipse GST have?
I am selling my 90 eclipse Fwd Turbo aka GS Turbo, has 175k with 15k on rebuilt head. Car has stock 14b turbo ported, 2g exhaust manifold, 2 1/2″ turbo back to sidepipe, safc, Mass air conversion kit (maft), front mount intercooler, hks cam gear cover, poly motor mounts all around, xtd stage 4 clutch, 255 fuel pump. Has NO power steering or AC!!
How do you change the ECM on a car?
Plug in the electrical wires to the ECM. The wiring harness will lock in once it is pushed in far enough. Connect the battery cables to the battery. Tighten the cables with a socket wrench. Start the vehicle and allow it to idle for five minutes. If there are still conflicting codes, the “Check Engine” light will come on.
Can a bad ECM cause a stick shift?
The ECM doesn’t control the transmission on a stick shift, so if you’re having problems with your five-speed, it’s the transmission. If you’ve done numerous repairs on the transmission and replaced your automatic transmission fluid and you’re still having problems, the ECM could be at the root of your problems.
What to do if your ECM is not working?
If your car seems to run fine but the Check Engine light won’t turn off, your ECM may be at fault. The only way to be sure is to visit a mechanic with the proper computer. They can analyze your vehicle’s error codes, and let you know exactly what the problem is.
The ECM doesn’t control the transmission on a stick shift, so if you’re having problems with your five-speed, it’s the transmission. If you’ve done numerous repairs on the transmission and replaced your automatic transmission fluid and you’re still having problems, the ECM could be at the root of your problems.
What is the Mitsubishi Eclipse service manual 2000-2002?
2000-2002 Eclipse Service Manual – Tearstone Skip to content Tearstone Mitsubishi Eclipse Performance Specialist Menu Factory Service Manuals 2000-2002 Eclipse Service Manual 2003-2005 Eclipse Factory Service Manual 2006 Eclipse Factory Service Manual 2006 Mitsubishi Eclipse Technical Information Manual Performance Tech Technical Installations
Plug in the electrical wires to the ECM. The wiring harness will lock in once it is pushed in far enough. Connect the battery cables to the battery. Tighten the cables with a socket wrench. Start the vehicle and allow it to idle for five minutes. If there are still conflicting codes, the “Check Engine” light will come on.
If your car seems to run fine but the Check Engine light won’t turn off, your ECM may be at fault. The only way to be sure is to visit a mechanic with the proper computer. They can analyze your vehicle’s error codes, and let you know exactly what the problem is.