Where is the radiator fan relay on a Dodge Grand Caravan?
If the resistance is greater than 1 ohm , repair the wire harness as necessary. If the Radiator fan control module has failed you will need to replace it with a new one there is no way to repair it. The radiator fan relay is located below the left front headlamp module. The headlamp module must be removed to access the relay.
What to do if your Dodge Grand Caravan radiator does not turn on?
Test the resistance of the wire harness between the PCM connector terminal 26 and the sensor harness connector. Also check for continuity between PCM connector terminal 43 and the sensor harness connector. If the resistance is greater than 1 ohm , repair the wire harness as necessary.
What to do if your radiator fan does not turn on?
Also check for continuity between PCM connector terminal 43 and the sensor harness connector. If the resistance is greater than 1 ohm , repair the wire harness as necessary. If the Radiator fan control module has failed you will need to replace it with a new one there is no way to repair it.
What does it mean when your radiator fan is not working?
This is what we call a blown fuse. A blown fuse is no big deal, and changing one does not cost a lot of money. If your car’s radiator fan is non-functional, check your car’s user manual and locate the fuse for the radiator fan controller or the fan.
What should the radiator temperature be in a Dodge Grand?
Normal operating temperature around 200°F ohmmeter should read approximately 700 to 1,000 ohms . Room temperature around 70°F ohmmeter should read approximately 7,000 to 13,000 ohms . Test the resistance of the wire harness between the PCM connector terminal 26 and the sensor harness connector.
If the resistance is greater than 1 ohm , repair the wire harness as necessary. If the Radiator fan control module has failed you will need to replace it with a new one there is no way to repair it. The radiator fan relay is located below the left front headlamp module. The headlamp module must be removed to access the relay.
Test the resistance of the wire harness between the PCM connector terminal 26 and the sensor harness connector. Also check for continuity between PCM connector terminal 43 and the sensor harness connector. If the resistance is greater than 1 ohm , repair the wire harness as necessary.
Why does my radiator not open the fan switch?
Almost seems like it has got to be crud inside the radiator where this normally closed COOLING FAN SWITCH screws into and is not opening the switch circuit when the coolant reaches the correct tempture. OR there is a circulation problem. Unpluging the connector and then the fans run, is the same thing as opening the circuit!!
What causes a car cooling fan to stop working?
There’s many reasons why a cooling fan could stop working, such as a bad sensor, relay, fuse and more. DIY car repair with Scotty Kilmer, an auto mechanic for the last 42 years. 1. Bluetooth Scan Tool: http://amzn.to/2nfvmaD 2. Cheap Scan Tool: https://amzn.to/2D8Tvae 3. Professional Socket Set: http://amzn.to/2Bzmccg 4.
Why is my Ceiling fan light not turning on?
If the connections seem to be secure, move the canopy back into place and tighten the screws to fasten it to the mounting bracket. Wiring for the ceiling fan light comes from the bottom of the fan motor. If these wires have disconnected, the fan blades can rotate but the ceiling fan lights won’t turn on.
Why are the lights on my dashboard not working?
Adjust the dial or knob to see if that fixes the problem. If the switch was accidentally bumped, your dashboard lights might have been turned off. Flip the switch or turn the dial or knob up and see if the lights on your dash come on or get brighter. If adjusting the switch doesn’t work, you may have a blown fuse or bad lightbulb.
How to troubleshoot a grand design gas grill?
Check fuse in fuse panel and replace if necessary. Make sure that return air grill is unobstructed. Remove anything that is stored in furnace compartment that could block airflow. Check that heat outlet registers are open and that register openings are unobstructed. Make sure that 12-volt power is present.