Where is the diagnostic port on a Honda Accord?
For the 1990 to 1995 Honda Accords, the diagnostic port is located by the passenger’s side kick panel. To access the connector, remove the panel using a Phillips screwdriver. For the 1996 to 2002 Honda Accords, the diagnostic port is located just bellow the bottom edge of the driver’s side dash.
Where is the OBD plug on a Honda Accord?
You will find below several pictures which will help you find your OBD connector in your car. The OBD2 socket is located under the steering wheel in the fuses box OBD socket is near the hood lever You can see the diagnostics port near the fuses
Where do I find the trouble code on my Honda Accord?
I need to pass the smog check but I don’t know what to do. You can retrieve your Honda Accord’s trouble code (s) yourself by using inserting a jumper wire at the diagnostic connector located in the passenger side kick panel. Insert the jumper wire in the 2 PIN service connector between pins 1 and 2. You should also see a 3 PIN connecter.
Where are the computer connectors on a Honda Accord?
There are seventeen typical auto computer connector locations. They are: Behind an ashtray. Bottom dash, above the hood release. Dash on right, underneath. Driver side of dash, above hood release-left hand side of instrument panel. Front of center console, driver side. Front of center console, passenger side.
For the 1990 to 1995 Honda Accords, the diagnostic port is located by the passenger’s side kick panel. To access the connector, remove the panel using a Phillips screwdriver. For the 1996 to 2002 Honda Accords, the diagnostic port is located just bellow the bottom edge of the driver’s side dash.
Where is the OBD plug on a 1991 Honda Accord?
The connector may be blue or yellow in color. If the connector has not been used before, you may find it still taped or strapped to the main wiring harness going to the ECU (engine control unit). Insert the jumper wire in the 2 PIN service connector between pins 1 and 2.
Where is the trouble code located on a Honda Accord?
Insert the jumper wire in the 2 PIN service connector between pins 1 and 2. You should also see a 3 PIN connector. This is used for a trouble code scanner. Trouble codes will be stored in the ECU even if the check engine light is not on.
When do you need an OBD scanner for a Honda Accord?
The 1990 to 1995 Honda Accords will require an OBD-II (On-Board Diagnostics) scanner. It will feature a pin-out design, which allows the device to connect to your car’s computer via a large socket. For Honda Accords manufactured between 1996 to 2000, an OBD-I scanner will be required.
The connector may be blue or yellow in color. If the connector has not been used before, you may find it still taped or strapped to the main wiring harness going to the ECU (engine control unit). Insert the jumper wire in the 2 PIN service connector between pins 1 and 2.
Insert the jumper wire in the 2 PIN service connector between pins 1 and 2. You should also see a 3 PIN connector. This is used for a trouble code scanner. Trouble codes will be stored in the ECU even if the check engine light is not on.
How to use a scanner on a Honda Accord?
Honda Accord: How to Use a Scan Tool. 1 Step 1 – Determine the appropriate scan tool. The 1990 to 1995 Honda Accords will require an OBD-II (On-Board Diagnostics) scanner. It will feature a 2 Step 2 – Locate the OBD socket. 3 Step 3 – Plug in the scanner. 4 Step 4 – Search and translate the trouble codes. 5 Related Discussion, Site, and Video.
You will find below several pictures which will help you find your OBD connector in your car. The OBD2 socket is located under the steering wheel in the fuses box OBD socket is near the hood lever You can see the diagnostics port near the fuses
Where can I find the DTC code on my Honda Accord?
On an OBD-I scanner, you will be able to retrieve codes through a series of flashes. Each DTC corresponds to a different problem in your vehicle. Search through the Honda Accord’s automotive repair manual or search online for the DTC to diagnose the exact problem, and then decide how to repair it. Figure 5.
Where can I get a Honda diagnostic scan?
Having a car diagnostic scanner at home—or safeguarded inside your vehicle’s glove compartment—could save you from spending hundreds of dollars at a local auto shop or Honda dealership.
How do you find the Diagnostic Code on a Honda OBD?
Turn ignition switch to ON position. Diagnostic Trouble Codes (DTCs) will be indicated by a series of long and short flashes on the Malfunction Indicator Lamp (MIL). The number of long flashes indicates the number in the 10s column. The number of short flashes indicates the number in the 1s column.
Where to buy Honda Accord engine control computer?
Buy Online. Pick Up In-Store. 10% OFF $75. Use Code: DIYSAVE10 Online Ship-to-Home Orders Only Producing over 270 horsepower and getting 35 miles per gallon put your Honda Accord at the head of the compact-car class. Your Honda Accord engine control module (ECM) keeps motor functions operating with precision.
Where do I find the OBD port on my car?
To determine which one you have, if your vehicle was built and sold in the US after January 1st, 1996 you will have an OBD 2 port. This service will allow you to find the OBD2 port location. Check out our other services! Get the year make model and engine type of a VIN.
Where are the sensors on a Honda Accord?
Fuel Tank Pressure Sensor Air Temperature Sensor ( Ambient / Intake 1 Manifold Pressure/Vacuum Sensor Power Steering Pressure Switch Throttle Position Sensor Transmission Position Sensor/Switch Variable Valve Timing Actuator Position Sensor Variable Valve Timing Pressure Switch Camshaft Position Sensor Crankshaft Position Sensor
To determine which one you have, if your vehicle was built and sold in the US after January 1st, 1996 you will have an OBD 2 port. This service will allow you to find the OBD2 port location. Check out our other services! Get the year make model and engine type of a VIN.
The 1990 to 1995 Honda Accords will require an OBD-II (On-Board Diagnostics) scanner. It will feature a pin-out design, which allows the device to connect to your car’s computer via a large socket. For Honda Accords manufactured between 1996 to 2000, an OBD-I scanner will be required.
What is the DTC code on a Honda Accord?
MIL will indicate DTC’s by outputting a number of flashes. Remember, these are manufacturer specific codes only. Refer to our Generic OBD II code list for definitions on all other Honda diagnostic trouble codes. Manufacturer Specific Codes P1106BARO Circuit Range/Performance Malfunction P1107BARO Circuit Low Input P1108BARO Circuit High Input
What is the diagnostic code for a Honda check engine light?
Refer to our Generic OBD II code list for definitions on all other Honda diagnostic trouble codes. P1201 Cylinder 1 Misfire – Compare possible causes/symptoms for this Honda check engine light code to the Generic OBD II code P0301
Where to find OBD I code on Honda Civic?
Honda Motor Corporation OBD I diagnostic trouble codes are retrieveable without any special tools by simply following the instructions here. The codes are listed for Accord or Civic models seperately when required. The codes are defined as to what system is affected. When possible we give the more commonly known OBD II component name.
On an OBD-I scanner, you will be able to retrieve codes through a series of flashes. Each DTC corresponds to a different problem in your vehicle. Search through the Honda Accord’s automotive repair manual or search online for the DTC to diagnose the exact problem, and then decide how to repair it. Figure 5.
Honda Motor Corporation OBD I diagnostic trouble codes are retrieveable without any special tools by simply following the instructions here. The codes are listed for Accord or Civic models seperately when required. The codes are defined as to what system is affected. When possible we give the more commonly known OBD II component name.
Since your Honda Accord is pre-OBD-II it does not have an OBD-II Data Link Connector which would normally used on a 1996 and newer Honda Accord; to pull trouble codes with a scan tool. On older model Accords, you can retrieve trouble codes by inserting a jumper wire at the diagnostic connector located in the passenger side kick panel.
What kind of oil do you put in a Honda Accord?
Additionally, General Motors issues Bulletin # 02-01-39-004B replacing PAG 150 oil with a lower viscocity oil. Thus, TechChoice now indicates PAG 46 (P46D) oil for those vehicles. All Engines – w/ Matsushita Compressor
How much refrigerant is in a Honda Accord?
Honda refrigerant and oil capacity charts Year Model Refrigerant Refrigerant Oil Type Ounces Type Ounces ACCORD 2003-2004 All Engines R134a 19.00 PAG 46 1994-2002 All Engines R134a 23.00 PAG 46
What are the specs of a 2003 Honda Accord?
* Does not apply to fluid and filter changes. See Owner’s Manual for details. ** Select AT models are SULEV-certified in California only (500 per month). MT models are LEV-II LEV for other CARB states – Fuel (gal.) **Based on 2003 EPA mileage estimates. Use for comparison purposes only. Actual mileage may vary.
What’s the price of a 2003 Honda Accord?
The original MSRP of the 2003 Honda Accord is from $16,260 to $28,360. The data above is updated daily, based on used car inventory for sale on CARFAX for the last five model years of this car.
Where was the 2003 Honda Accord last serviced?
Purchased on 10/29/03 and owned in OH until 04/24/21. Driven an estimated 5,862 miles/year. Last serviced at 102,549 miles in Euclid, OH on 04/17/21 • Vehicle serviced • Oil and filter changed. No accident or damage reported to CARFAX. Purchased on 06/26/03 and owned in CA until 06/06/21. Driven an estimated 6,815 miles/year.
What do I need to know about Honda OBD I?
Honda OBD I Diagnostic Trouble Codes Code Model Description 0 Accord Civic No Signal To Engine Control Module (ECM 1 Accord Civic Problem In Heated Oxygen Sensor (HO2S) C 3 Accord Civic Electrical Problem In Manifold Absolute 4 Accord Civic Open Or Shorted Crank Sensor (CKP) Signa
Where is the OBD-II plug on a 1995 Honda Accord?
The Location of the OBD-II Plug on the 1995 Honda Accord. OBD-II (On-Board Diagnostics) systems use internal sensors and an on-board computer to monitor your vehicle’s performance. The computer gathers information and performs routine tests at various points of operation to ensure the proper operation of your vehicle.
Where is my OBD2 port in Honda Civic?
The norm states that the port must be located inside the vehicle passenger compartment. Depending on the make and model, it may or may not be easy to locate. To diagnose your vehicle yourself, download our EOBD-Facile car diagnostic software. Use our search engine below to locate your OBD2 port! Civic 10 (2016 – …) NC700 (2012 – …)
Why do I need a scan on my Honda Accord?
Scanners deliver expensive diagnostic reports every time the check engine light turns on, and lets you monitor the health of your car from the comfort of your own garage. These simple tools allow you to diagnose a problem as it arises.
What should I do if my Honda Accord misfire?
Honda Accord engine misfire and ignition coil diagnose. – YouTube Honda Accord engine misfire and ignition coil diagnose. If playback doesn’t begin shortly, try restarting your device.
Are there any problems with the Honda Accord?
Notably, all 2001 through 2012 Honda Accord models are affected by the Takata airbag recall. The airbags in these vehicles must be replaced due to a safety fault that could cause them to explode. Over 190,000 car shoppers have purchased a car through the U.S. News Best Price Program.
What kind of error code does Honda Accord have?
This repair also applies to 2002, 2003, 2004, 2005, 2006, and 2007 Honda Accords, as well as other Honda’s using the i-VTEC engine (Honda Element, Honda Civic, Honda CRV), with perhaps some variations depending on the vehicle. This issue can also produce a P2646 error code.
Where is the OBD connector on a Honda Accord?
OBD connector location for Honda Accord (1997 – 2002) You will find below several pictures which will help you find your OBD connector in your car. OBD Connector is located on the central console (passager side) Go to the OBD2.
Where can I get a Honda Accord navigation update?
Consult your vehicle owner’s manual or learn how to determine your model year based on your VIN. The Honda Navigation Store is your official online source for Accord GPS navigation system map updates. The Accord update features fresh data that helps improve routing accuracy and fuel economy.
Where are the OBD connectors located on a Honda?
An example would be a manufacturer that locates the connector under the passenger side of the dash in 1996, doesn’t mean that the next year it wouldn’t be under an ashtray or somewhere else. Additionally, some connectors are located upside down, so some attention needs to be paid to this factor when trying to connect.
Where is the OBD2 port on a Honda Accord 7?
OBD2 port Honda Accord 7 (2003 – 2008) – Find your plug ! Where is my OBD2 port ? All vehicles are equipped with an OBD port to which you can connect your klavkarr diagnostic case.
There are seventeen typical auto computer connector locations. They are: Behind an ashtray. Bottom dash, above the hood release. Dash on right, underneath. Driver side of dash, above hood release-left hand side of instrument panel. Front of center console, driver side. Front of center console, passenger side.