Where is the diagnostic plug on a Subaru Legacy?
The On-Board Diagnostic port (known as OBD2 or OBD-II) in Subaru vehicles is located under the dashboard on the driver’s side. You will need to look deep under the dashboard (above the brake pedal) for the 16 pin connector shown below. All Subaru vehicles from 1996 and newer have an On-Board Diagnostic (OBD) port.
Where is the OBD port on a Subaru Outback?
OBD connector location for Subaru Outback (2009 – 2014)
- The OBD II socket is located at the bottom left of the steering wheel.
- The OBD connector is visible above the footrest.
- Here is the OBD socket.
How do you reset the check engine light on a 1997 Subaru Legacy?
How to Reset a Subaru Check Engine Light
- Open the hood of your Subaru and loosen the nut that holds the cable clamp to the negative battery terminal.
- Slide the cable off the negative battery terminal.
- Wait 5 minutes, then reconnect the cable and tighten the retaining nut.
Where is the OBD-II diagnostic port always located?
The OBD-II port is usually located under the dashboard, beneath the steering wheel column (1 – 3 in the diagram below).
What OBD2 protocol does Subaru use?
Subaru OBD-2 compatibility list
| Model | Engine | OBD-2 Protocol |
|---|---|---|
| Subaru OUTBACK | 2.5i, Gasoline or LPG (165HP) | KWP FAST |
| 2.5l gpl, Gasoline or LPG (165HP) | KWP FAST | |
| 3, Gasoline (245HP) | CAN 11bit (500kb) | |
| Subaru Outback Wagon | ISO 14230-4, ISO 9141-2 |
What is OBD1?
OBD1 is a diagnostic system that only supports cars made before 1996. Introduced in 1991, it does not support all older models. The downside of these scanners is that they are manufacturer specific. One scanner won’t work on two different brands even if they have the same issues.
How do you use the code reader on a Subaru Outback?
How do I Connect OBD-II to a Subaru Outback?
- Remove the lower dashboard panel on the driver side of your Subaru Outback.
- Look for the OBD-II data link connector (DLC).
- Plug your OBD-II scanner into the DLC on your car and turn the scanner on and your car on.
- Read the code displayed the scanner and record it.
What’s the difference between OBD and OBD2?
OBD1 is connected to the console of a car, while OBD2 is remotely connected to the vehicle. 2. OBD1 was used during the earlier years of the car manufacturing industry, while OBD2 was only introduced in car models produced in the early 1990’s.
Is there a fuse for the OBD port?
Usually there is a fuse for the OBD port, if you cannot find they the fuse for the cigarette lighter and the auxiliary ports. Even a fuse dedicated solely to the car’s computer diagnostics can blow for no apparent reason. Check your fuses to see if any have gone bad.
Where to find check engine light code on Subaru?
When retrieving Subaru check engine light codes with an OBD II scan tool, proceed as follows: 1. Connect scan tool to the 16-pin data link connector (DLC) located underneath the steering column. The connector may have a removable cover. 2. Turn the ignition on.
Where is the diagnosis connector on a Subaru Outback?
Subaru has moved the location of the diagnosis connector a few times, and admittedly even the factory manual can be wrong in that respect. Once you find the connector, the rest of the factory info can be applied, and it’s pretty straightforward. Yes, that’s correct to retrieve the ABS code (s).
What kind of engine light does a Subaru Outback have?
I have a engine light question re: my 2005 Subaru Outback 2.5i wagon. :confuse: After driving from MD to NC and back this past weekend (with no problems) today I was driving around and, mid-way thru errands, the yellow “Check Engine” light turned on, and the green “Cruise Control” light started to blink on and off.
Where is the diagnostic port on a Subaru?
The On-Board Diagnostic port (known as OBD2 or OBD-II) in Subaru vehicles is located under the dashboard on the driver’s side. You will need to look deep under the dashboard (above the brake pedal) for the 16 pin connector shown below.