Where can I find a Mercury Mariner thermostat kit?
Find thermostat kits for your Mercury Mariner outboard using the application chart from the Mercury Quicksilver catalog. Need other parts? If you need parts not listed in the application guide, please see:
What happens when the thermostat goes out on a Mercury Sable?
The thermostat installed on your Mercury Sable’s 3.0l engine is what allows coolant to flow from the radiator to the engine. When the thermostat goes out, your engine temperature will start to rise with use, and you could overheat the engine and cause permanent damage.
How long does it take to replace a car thermostat?
Replacing the thermostat isn’t an incredibly difficult process, but it will take at least an hour to do correctly. Allow the vehicle to cool completely before working the cooling system. You should be able to put your hand flat on the top of the engine without burning yourself, otherwise you risk burning yourself from hot coolant.
How do you remove a thermostat from a radiator?
Drain out approximately half of the coolant in the radiator. This should minimize any spillage when removing the thermostat housing. Unbolt the thermostat housing from itself using the 3/8-inch ratchet and socket. Lower down the stock thermostat and o-ring. Remove both the thermostat and the o-ring and discard.
The thermostat installed on your Mercury Sable’s 3.0l engine is what allows coolant to flow from the radiator to the engine. When the thermostat goes out, your engine temperature will start to rise with use, and you could overheat the engine and cause permanent damage.
What do you need to change a boat thermostat?
You will need and 8mm wrench for the thermostat bolts and a 15mm for the two fuel rail bolts. Included copy of invoice from IBoats www. iboats .com (great cheap place to order thermostats) my local boat house here wanted over 30 bucks for one thermostat not including new rubber washer.
Replacing the thermostat isn’t an incredibly difficult process, but it will take at least an hour to do correctly. Allow the vehicle to cool completely before working the cooling system. You should be able to put your hand flat on the top of the engine without burning yourself, otherwise you risk burning yourself from hot coolant.
Drain out approximately half of the coolant in the radiator. This should minimize any spillage when removing the thermostat housing. Unbolt the thermostat housing from itself using the 3/8-inch ratchet and socket. Lower down the stock thermostat and o-ring. Remove both the thermostat and the o-ring and discard.
What are the parts of a Mercury Mariner water pump?
2 Models with aluminum water pumps. 3 Models with plastic upper pump housings. 4 Models with plastic water pumps. 5 Pump screws without insulators. 6 Pump screws with insulators. 7 Models with driveshaft retaining nut. 8 Models without a driveshaft retaining nut. 9 Models with flush hole. 10 Models without flush hole.
What kind of outboard does a Mercury Verado have?
Meet the most powerful, most innovative outboard in Mercury history. The 7.6L V12 600hp Verado. It starts with the perfect wake, crafted for you. MERCURY V8 & V6 OUTBOARDS – Delivering legendary performance. Upgrade with Mercury. Your boat still has a lot of memories left to make.
What kind of outboard does Mercury boat use?
MERCURY V8 & V6 OUTBOARDS – Delivering legendary performance. Upgrade with Mercury. Your boat still has a lot of memories left to make. Give it the power it needs to continue propelling you on your adventures with a new Mercury outboard.
Is the Mercury Merc the same as the Mariner?
The small twin cyl Mercs and Mariners were indeed Yamahas for many years. Many models of the Mercury and Mariner are indeed the same unit with different decals. There were a few models that the Merc used the larger diameter gearcase while the Mariner used the smaller gearcase.
2 Models with aluminum water pumps. 3 Models with plastic upper pump housings. 4 Models with plastic water pumps. 5 Pump screws without insulators. 6 Pump screws with insulators. 7 Models with driveshaft retaining nut. 8 Models without a driveshaft retaining nut. 9 Models with flush hole. 10 Models without flush hole.
When did the Mercury Mariner come on the market?
No accident or damage reported to CARFAX. 1st owner purchased on 10/15/09 and owned in ND until 12/17/10 • 2nd owner purchased on 12/17/10 and owned in MN until 12/12/11 • 3rd owner purchased on 03/30/12 and owned in MN until .
What kind of motor does Mercury Verado outboard have?
With the unwavering strength of a V12 powerhead, the 600hp Verado outboard delivers extraordinary range and performance to take your boating adventures to new destinations. Mercury redefined the way horsepower meets the water by building the first-ever V12 outboard. At 500hp, it’s our most powerful, most capable commercial outboard yet.
Find thermostat kits for your Mercury Mariner outboard using the application chart from the Mercury Quicksilver catalog. Need other parts? If you need parts not listed in the application guide, please see:
How to find out model number of Mercury outboard motor?
Simply enter the original model or serial number assigned to your outboard motor by Mercury Marine. Mercury uses a specific system when assigning either serial or model numbers to their Mercury Outboard Motors, however either of these can be used to lookup OEM parts for your motor.
How do you remove a thermostat from a car?
Remove the thermostat housing by using a socket wrench to undo the bolts holding it onto the engine block. Once the housing is free, remove the old thermostat from the housing and discard it.
Where is the thermostat housing on a radiator?
Locate the thermostat housing at the other end of the top radiator hose from the radiator. You are going to drain the radiator so that the coolant will be just below the level of the thermostat housing.