Where can I find a liftgate control module?
Based on the need to dealer program a new module I am looking for a used one that apparently can be used plug and play with existing programming. I have located a module for a 04 EXT long wheel base and want to know if that is the same part that is used on the short wheelbase. Thanks for the help.
Why is my lift gate not opening automatically?
2014 Pathfinder Platinum: liftgate will not open manually or with key fob or with button in car. It makes no noise. Last week it would only open … read more Lift gate is not opening automatically. It unlatches Lift gate is not opening automatically. It unlatches manually. But why won’t it open automatically. … read more
Where is the liftgate button on a Nissan?
Customer: 2014 Nissan … read more I push the liftgate button, either the button by the license plate, on the key fob or on the dash under the steering wheel and nothing happens. No, beep … read more
What should I do if I Lost my liftgate remote?
Just checking to make sure you know you have a good data communication wire, since it can flex and break inside the wire insulation hidden by a rubber boot up at the liftgate hinge line and not be obvious. Assume you’ve just lost the use of the remote unlock function, rear wiper, and defogger.
Based on the need to dealer program a new module I am looking for a used one that apparently can be used plug and play with existing programming. I have located a module for a 04 EXT long wheel base and want to know if that is the same part that is used on the short wheelbase. Thanks for the help.
Why does my liftgate not turn on when I press the up button?
Usually, if this is a switch problem, one of the two switches will work fine. If both switches do not turn the liftgate on, then you probably have a broken wire inside the pump & motor box. f. Motor runs but platform goes down when the up button is pressed. Hoses are reversed where they connect to the power unit box.
Just checking to make sure you know you have a good data communication wire, since it can flex and break inside the wire insulation hidden by a rubber boot up at the liftgate hinge line and not be obvious. Assume you’ve just lost the use of the remote unlock function, rear wiper, and defogger.
What to do if one of the coils on the liftgate is bad?
Coil has power. If in your test the platform closes fine but will not open (or the opposite) either the one coil is bad or the valve. If coil is getting power you can reverse the two coils and try the function again. If the one coil is bad the opposite will happen. If the opposite does not happen replace the coils and valve.
What to do if liftgate does not lock properly?
A welding tip cleaner can be used to clean the hole out if it is contaminated. 5.1) Platform will not lock properly on both sides. Power the liftgate platform up to the top before locking the platform. Hold the button at the top for 5-10 seconds to relevel the platform.
What to do when liftgate platform goes out of sync?
Power the liftgate platform up to the top before locking the platform. Hold the button at the top for 5-10 seconds to relevel the platform. Sometimes if the platform goes out of sync it may need to be relevelled at the top before it goes into the locks properly. 6.1) Platform leaks down.
When to replace the solenoid on a liftgate?
Check motor solenoid. If it is getting power but you Do not hear click, you should change the motor solenoid. 1.3) If the motor solenoid is getting power and you can hear it click, replace motor. 2.1) Liftgate makes squealing noise: a. Noise happens in both raising and lowering. Use Caterpillar additive 1U-9891.
Are there any problems with the lift gate?
1) Where the wire harness passes from the lift gate to the roof/body. The wires have been known to chaffe inside that flexible rubber boot causing all sorts of odd behavior. Pull the boot at each end and inspect each wire thoroughly. 2) The lift gate module and the license plates share a common ground (G401, inside the rear-most body pillar).
How can I program new lift gate module on 2011 caddiliac SRX?
1. Connect the scan tool to the vehicle. 2. Select Module Diagnosis. 3. Select Liftgate Control Module. 4. Select Liftgate Maximum Open Position Learn. 5. Press “Launch” and follow the on screen instructions. Chad Farhat, ASE Certified Technician A6 – Electrical / Electronic systems A7 Heating / Air conditioning systems Category: Cadillac
How does the hands free liftgate sensor work?
The liftgate operates when the sensor detects a kicking motion. The hands-free liftgate sensor control module sends a serial data message to the liftgate control module, which activates the liftgate motor in the liftgate power assist actuator. The tail lamps flash when the command has been received.
When does a key fob not work on a liftgate?
• The projected logo will not work for a single key fob when a key fob has been left within approximately 15 feet (5 meters) of the liftgate for several minutes, has been left inside the vehicle and all vehicle doors are closed, or has approached the area outside of the liftgate several times in a short period of time.
How do I Turn Off the kick function on my liftgate?
The kick function can be turned off, only open the liftgate, or open and close the liftgate. To change the kick function: 1. Select the Hands-free Liftgate Control menu on the infotainment screen under Settings > Vehicle > Comfort and Convenience.
What does ACDelco liftgate control module stand for?
ACDelco GM Original Equipment Liftgate Control Modules are the receivers for the remote keyless entry and transmits keyless entry commands to the body control module. They are a GM-recommended replacement for your vehicle’s original components.
What happens if there is no ground in a liftgate?
You still need to check for continuity through the wiring to the defrost grid and out to ground. You can have all the power you need at the fuses, but if there’s no ground, there’s no place for the current to go, assuming it’s reaching the grid in the first place.