Where are the fuse panels on a Toyota Sienna?

Here you will find fuse box diagrams of Toyota Sienna 2004, 2005, 2006, 2007, 2008, 2009 and 2010, get information about the location of the fuse panels inside the car, and learn about the assignment of each fuse (fuse layout) and relay.

How to change tail light on Toyota Sienna?

Change tail or reverse light with only a single tool. The trick is getting the panel off. Buy lights: Be sure to look up the correct bulb number in your owner manual. Donations appreciated – click in upper right corner “info” circle. Loading…

How many power outlets are in a Toyota Sienna?

Fuse box diagram № Name Ampere rating [A] Circuit 1 P/OUTLET 15 Power outlets 2 RAD NO.2 7,5 Audio system, navigation system, rear se 3 ECU-ACC 10 Main body ECU, clock, shift lock system, 4 CIG 15 Power outlets

Where are the fuses in a Toyota Sienna?

Fuse box diagram: Toyota Sienna (XL30; 2011-2018) Cigar lighter / power outlet fuses in the Toyota Sienna are the fuses #1 “P/OUTLET” and #4 “CIG” in the Instrument panel fuse box. The fuse box is located under the instrument panel (on the left side), behind the lid. Assignment of the fuses in the Passenger Compartment Fuse Box.

Why does my EFI fuse keep blowing out?

Many Toyota owners have a problem with the electronic fuel injection (EFI) fuse blowing repeatedly. Here are some things to check: 1) The wires around the EGR tube for melting or fraying. 2) The wires near the EGR vacuum switching valve (VSV) located under the intake manifold.

Where are the fuses on a Toyota Ricks?

2) The wires near the EGR vacuum switching valve (VSV) located under the intake manifold. 3) Wires pinched between the intake manifold and the cylinder head. 4) Wires pinched anywhere along the valve cover. 5) Check injector wiring for any pinched locations.

What kind of Fuse is 120 amp alternator?

It must’ve been brief, because I didn’t see/hear/feel a spark. So the 120 amp fuse for the alternator is a PAL type fuse, and it is a bit of a PIA to remove. I’m a mechanic, so it wasn’t very difficult for me, just time consuming.

What to do if your alternator blows fuse?

From there, I had to push in all the tabs on the side of the fuse box to separate it so I could gain access to the screws holding the fuse blades to the terminals themselves. Once in half, I had to fish my a socket past the mess of wires inside the box, and unscrew both terminals.

What should the voltage be on a Toyota alternator?

Turn the key, and I get nothing, not even a click. I check the battery voltage, read 13.1 volts, so I am fine there. I have lights, radio, door chime, etc. Next I check the alternator to make sure it’s hooked up correctly, and it is. I’m getting frustrated at this point, but decide to check the fuses.

Why is my Fuse Box making a clicking noise?

This can be caused by a computer failure, resistance in the ground wire for the control side of the relay or high resistance in the power supply to the control side of the relay. To find out the source of the problem, you’ll need to run some quick tests using a multimeter.

What to do when your fuse box wont turn on?

Turn on the ignition key, then touch the positive lead of the multimeter to the negative battery terminal. If the voltage varies, the problem lies in whatever is supposed to activate the relay — the computer or a switch, for example. Inspect, the wiring for terminal No. 86 and make any repairs as needed.

What is this clicking sound while trying to charge the Van?

Also, the clicking usually coincides with the console turning on/off or blinking. I tried putting the charger/starter on the jump start setting then tried to start the van, but no luck.

Navigation