Where are the fuse panels on a Hyundai Sonata?
Here you will find fuse box diagrams of Hyundai Sonata 2005, 2006, 2007, 2008, 2009 and 2010, get information about the location of the fuse panels inside the car, and learn about the assignment of each fuse (fuse layout) and relay.
Why does my Hyundai Tiburon radio not work?
I plugged the stocker back in and same thing, no power. Check the wire harness to the radio and those r all good. Also I have an edge cs multigauge obd-II reader and I’m not getting any power to that either. Any ideas guys what’s cause thing this? hmmmm….
Where are the fuses on a Hyundai Tiburon?
Click to expand… remove the BCM & fuse panel cover directly in front of your left knee, then get down and look towards the top left side of the BCM and you will see the yellow fuse cover. pull it out and flip the top up to access the fuse itself. (the yellow cover doesnt come out all the way).
What to do if your car radio won’t turn on?
ROOM LP did the trick! Take some small gauge wire directly to the battery terminals, and connect to the correct pins on your radio harness/plug (yellow for power, black for ground). See if it even turns on with direct power.
How many fuses are in a Hyundai Sonata?
Hyundai Sonata (2009 – 2010) – fuse box diagram Year of production: 2009, 2010 Engine Compartment Description Ampere rating [A] Protected component FUSIBLE LINK ABS.1 40 ABS/ESC control module, Multipurpose check connector ABS.2 20 ABS/ESC control module, Multipurpose check connector I/P B+1 40 Fuse 23, 24, 30, 31, 32, 33, 34, 35 RR HTD 40 …
I plugged the stocker back in and same thing, no power. Check the wire harness to the radio and those r all good. Also I have an edge cs multigauge obd-II reader and I’m not getting any power to that either. Any ideas guys what’s cause thing this? hmmmm….
ROOM LP did the trick! Take some small gauge wire directly to the battery terminals, and connect to the correct pins on your radio harness/plug (yellow for power, black for ground). See if it even turns on with direct power.
Click to expand… remove the BCM & fuse panel cover directly in front of your left knee, then get down and look towards the top left side of the BCM and you will see the yellow fuse cover. pull it out and flip the top up to access the fuse itself. (the yellow cover doesnt come out all the way).
Here you will find fuse box diagrams of Hyundai Sonata 2002, 2003 and 2004, get information about the location of the fuse panels inside the car, and learn about the assignment of each fuse (fuse layout) and relay.
Is the RPM gauge on my Sonat 4cyl working?
Have an 04 Sonat 4cyl with 141,000 miles. RPM Gauge doesn’t work most of the time and check engine light is on. Went to Oriles and they said the code was p0320….
Why is the RPM gauge on my Hyundai not working?
More than likely your crankshaft sensor has completely failed or fails once it heats up. The ECM takes the readings from the crankshaft and camshaft position sensors and uses that to determine when to fire the injectors, spark the plugs and shift the transmission.
Where is the fuse box in a car?
Your car’s fuse box holds a variety of fuses with different ratings and most likely several relays. It is located under the hood in the engine bay, typically somewhere easy to get to that is less likely to be damaged in a collision. However, it is common for there to be an additional interior fuse panel inside the cab of the vehicle.
How many fuses does a car fuse panel hold?
Average rating from 124,233 customers who received a Fuse Box Replacement. A fuse box, also known as a fuse panel, organizes all of the car’s fuses in one area for easy access. Your car’s fuse box holds a variety of fuses with different ratings and most likely several relays.
How do you change the fuse on a car?
Note: Set the negative cable aside where it will not make contact with metallic objects around it. Step 2: Locate and open the fuse panel. Open the hood and locate the fuse panel. It will have a cover over the fuses and you will need to remove the cover to access the panel.
Here you will find fuse box diagrams of Hyundai Sonata 2005, 2006, 2007, 2008, 2009 and 2010, get information about the location of the fuse panels inside the car, and learn about the assignment of each fuse (fuse layout) and relay.
Where is the fuse box on a Hyundai Elantra?
Fuse box located. The fuse box for the lights and other electrical accessories will be found in the backside of multi box located in the left side of driver. Inside the box you will find a list showing the circuits protected by each fuse.
What is in the fuse box on a Hyundai Accent?
Instrument cluster, Courtesy lamp, Trunk room lamp, ETACM, DLC, Door warning, Multipurpose check connector ECM, A/T shift lever, Transaxle range switch, Mass air flow sensor, Vehicle speed sensor, Water sensor
Where is the fuse box on my car?
Fuse box located. The fuse box for the lights and other electrical accessories will be found in the backside of multi box located in the left side of driver. Inside the box you will find a list showing the circuits protected by each fuse. fuse box diagram.
What kind of Fuse does a Hyundai Santa Fe have?
Hyundai Santa Fe (2004 – 2006) – fuse box diagram Year of production: 2004, 2005, 2006 Engine compartment Description Ampere rating [A] Protected components FUSIBLE LINK ALT 120 Generator B+ 50 Tail lamp relay, Fuse 11~17, Power connector IGN 50 Start relay, Ignition switch BLR 40 A/C Fuse, Blower relay ABS.1 30 ABS control module, …
What causes the tail lights to go out on a Hyundai Sonata?
The contacted stated the failure first occurred when driver side rear taillight burn out, shortly after the passenger rear taillight and front driver side head light. Also burn out in which the contact replace the bulbs and from each taillight. The sockets for each where melted into the into bulb and taillights.
Are there any problems with the tail light switch?
Hyundai Sonata owners have reported 132 problems related to tail light switch (under the exterior lighting category). The most recently reported issues are listed below. Also please check out the statistics and reliability analysis of Hyundai Sonata based on all problems reported for the Sonata.
Where are the fuse panels on a Hyundai Santa Fe?
Here you will find fuse box diagrams of Hyundai Santa Fe 2004, 2005 and 2006, get information about the location of the fuse panels inside the car, and learn about the assignment of each fuse (fuse layout) and relay. Information from the owner’s manuals of 2004, 2005 and 2006 is used.
What happens when your tail lights are not working?
When the tail lights fail or do not function properly the car becomes a danger or hazard to self and others on the road. You may receive a ticket or citation from the traffic police. Blow fuse – The first thing the mechanics check is the fuse corresponding to the rear lights.
How can I tell if my tail lights have a fuse?
When you have located the fuse for the tail lights use a fuse tester to check the connection. If the tester lights up – your fuse is functioning fine. If it does not light up then, replace the fuse with another of the similar amperage and size. In many instances, you can see the break in the metal strip of the fuse.
When did the Hyundai Sonata YF come out?
In this article, we consider the sixth-generation Hyundai Sonata (YF), produced from 2010 to 2014. Here you will find fuse box diagrams of Hyundai Sonata 2011, 2012, 2013 and 2014 (+Hybrid), get information about the location of the fuse panels inside the car, and learn about the assignment of each fuse (fuse layout) and relay.
Where is the fuse box on a Hyundai i20?
The fuse box is located in the engine compartment (left-side). Inside the fuse/relay panel covers, you can find the label describing fuse/relay name and capacity.
In this article, we consider the sixth-generation Hyundai Sonata (YF), produced from 2010 to 2014. Here you will find fuse box diagrams of Hyundai Sonata 2011, 2012, 2013 and 2014 (+Hybrid), get information about the location of the fuse panels inside the car, and learn about the assignment of each fuse (fuse layout) and relay.
The fuse box is located in the engine compartment (left-side). Inside the fuse/relay panel covers, you can find the label describing fuse/relay name and capacity.
What causes a fuse to blow on a blower motor?
If the blower motor relay develops any sort of problem that hinders its ability to properly limit and distribute power, it may cause the blower motor fuse to blow. Any sort of electrical spikes or excessive current from a bad relay will blow the fuse and cut power in order to protect the system.
Where is the blower control switch on the dashboard?
The blower control switch on the dashboard controls the circuit flow of the blower motor to adjust the voltage from low, to medium, to medium-high, to high. When on high, the circuit bypasses the blower resistor.
How do you change the light bulb on a Hyundai Sonata?
Disconnect the power cord from the bulb base at the back of the assembly. Push the bulb spring on the assembly to remove the light bulb. Pull the old bulb out and place the new bulb in. The low-beam lights use H7 bulbs. The high-beam lights use H1 bulbs. Reattach the bulb spring and reconnect the power cord. Refasten the plastic covers.
Why are my head lights not working on my Sonata?
Loose electrical connections, burned out bulbs and popped fuses create most headlight problems, and all three have a quick fix. Turn off the engine. Allow it to cool down before checking the connections. Open the hood. Lightly tug on the electrical connector at the rear of Sonata’s headlamp assembly.
Is there a problem with the Hyundai headlight?
Hyundai makes it impossible to find answer to the headlight problem. I cannot believe the united front of bullshit that I have received from half a dozen hyundai dealer repair or parts reps. They all say there is no schematic or id for fuses for the headlight.
What is the fuse box on a sonata?
Hyundai Sonata (2003 – 2004) – fuse box diagram Year of production: 2003, 2004 Under hood junction box Description Ampere rating [A] Protected component COND FAN 20 Condenser fan PWR WIND 40 Power window ABS 2 20 ABS IGN SW-1 30 Ignition switch ABS 1 40 ABS IGN SW-2 30 Ignition switch RAD FAN MTR …
Disconnect the power cord from the bulb base at the back of the assembly. Push the bulb spring on the assembly to remove the light bulb. Pull the old bulb out and place the new bulb in. The low-beam lights use H7 bulbs. The high-beam lights use H1 bulbs. Reattach the bulb spring and reconnect the power cord. Refasten the plastic covers.
Loose electrical connections, burned out bulbs and popped fuses create most headlight problems, and all three have a quick fix. Turn off the engine. Allow it to cool down before checking the connections. Open the hood. Lightly tug on the electrical connector at the rear of Sonata’s headlamp assembly.
Hyundai makes it impossible to find answer to the headlight problem. I cannot believe the united front of bullshit that I have received from half a dozen hyundai dealer repair or parts reps. They all say there is no schematic or id for fuses for the headlight.
What happens when the starter relay is stuck?
If the starter stays on after the engine has ignited, the main contacts in the starter relay have most likely welded together in the closed position. When this occurs, the starter relay will be stuck in the on position and damage will occur to the starter, circuit, relay, and the transmission flywheel if it is not addressed immediately.
Are there any problems with the Hyundai Sonata starter?
Hyundai Sonata owners have reported 60 problems related to starter (under the electrical system category). The most recently reported issues are listed below. Also please check out the statistics and reliability analysis of Hyundai Sonata based on all problems reported for the Sonata.
Are there any recalls on the Hyundai Sonata?
Sonata recall: well for starters I almost got hit by a 18 wheeler because the car shut off on the interstate while I was driving. Lucky I was to get the car to the side of the road but it hit the side rail because I couldnt get it to stop. Now the car will not start at all.
What should I do if my car fan is not working?
Blower still does not work. Checked continuity of 40 amp blower fuse; it’s okay. Checked most fuses for continuity in the PDC and Junction Box and they are okay. Note, there is no burnt or corroded wiring.
Where is the fuse on a Toyota heater?
the heater fuse/relay is behind the kick panel on the p/s of the car (kick panel is the panel under the dash and between the door and firewall) also while you are down in that area check to make sure the blower motor is getting voltage aka bad blower motor) I think it’s actually a 30A circuit breaker instead of a fuse.
Why does my blower fan not keep working?
There’s a switch or something located under the blower fan that goes bad, and not all the fan speeds will keep working. Like on mine, the lowest fan speed no longer works, but the rest do. That’s the blower resistor.
What are common reasons my Hyundai Sonata has heater problems?
What are common reasons my Hyundai Sonata has heater problems? While there are a variety of reasons your Hyundai Sonata heater is not working, the most common 3 are a broken heater blower motor, a problem with the thermostat, or a failed heater blower motor resistor.
Why is my Hyundai radiator fan not running?
That can be caused by a faulty engine coolant temperature sensor or a wiring problem between the ECM and pin 3. If you do find ground on pin 3, jumper across pins 1 & 2 in the socket. If the radiator fan runs, then the radiator fan relay is bad. Replace it. If the fan still doesn’t run, provide battery power and ground directly to the fan.
What to do when your AC Fan is not working?
Checked for incoming resistance ground to the blower, from the dash control switch and it works. Checked for battery at the blower, when the car is running. There is no battery to operate the blower. Rotated all the PDC relays around, they have the same ID, other than ABS pump.
What to do if radiator fan doesn’t activate?
If you’ve confirmed the fusible links are good proceed by placing the relays back in their sockets, run the engine at idle and wait for the radiator fan to activate while watching the temperature gauge. If the gauge rises into the danger zone but the radiator fan doesn’t activate, remove the radiator fan relay and check for ground on pin 3.
What causes a bad or failing blower motor relay?
Blown fuses. One of the first symptoms of a bad or failing AC blower motor relay is a blown AC blower motor relay circuit fuse. If the blower motor relay develops any sort of problem that hinders its ability to properly limit and distribute power, it may cause the blower motor fuse to blow. Any sort of electrical spikes or excessive current…
What is the fuse box on a Hyundai Accent?
ECM, PCM, Canister Purge Control Solenoid Valve, Variable Intake Solenoid Valve, Canister Close Valve, Immobilizer Module, A/CON Relay, Cooling Fan (High) Relay, Cooling Fan (Low) Relay PCM, Transaxle Range Switch, Instrument Cluster, Rear Combination Lamp LH/RH, ATM Shift Lever Switch ILL.
Blown fuses. One of the first symptoms of a bad or failing AC blower motor relay is a blown AC blower motor relay circuit fuse. If the blower motor relay develops any sort of problem that hinders its ability to properly limit and distribute power, it may cause the blower motor fuse to blow. Any sort of electrical spikes or excessive current…
If the blower motor relay develops any sort of problem that hinders its ability to properly limit and distribute power, it may cause the blower motor fuse to blow. Any sort of electrical spikes or excessive current from a bad relay will blow the fuse and cut power in order to protect the system.
The blower control switch on the dashboard controls the circuit flow of the blower motor to adjust the voltage from low, to medium, to medium-high, to high. When on high, the circuit bypasses the blower resistor.
Where are the interior lights on a Hyundai Sonata?
Just as a side note regarding the Sonata’s interior lighting choices. As an older car guy, I remember when almost all cars had an interior light sw between the two doors about 3/4’s up the side post between the front and rear doors. Easy to reach from the outside of the car.
Are there any problems with the Hyundai Sonata?
If I have any complaints regarding my Sonata it is the interior light switches. I have a sun roof and this puts my ceiling light switch to far to the rear to reach, and the lights switches over the center column are not lighted and I can not find the D** things when it is dark. Other than that, I am very happy with my 06 Sonata.
Can you use both lights on a 2009 Sonata?
To me, 2009 Sonata owner, its not a big deal and easy for me to reach both lights while driving. Although I don’t tend to use the rear light often, but have used the map lights once or twice. You just need to consider the traffic or surrounding area for a few seconds before reaching up for the light.
Why do the lights on my Hyundai Sonata not turn off?
My research so far indicates that the fuse box and the bcm are separate units in the 2007 sonata, but they are combined in later models. Any help with this would be appreciated. Same issue as everyone above. Lights will not always turn off when you switch them off. Driving lights will stay on and have caused the battery to drain twice.
Where is the headlamp fuse on a Hyundai Sonata?
Locate the under-hood junction box on the driver’s side of the vehicle, behind the engine. Remove the cover and locate the fuse labeled “HD LP LO.” This is the headlamp fuse.
What kind of light bulb does a Hyundai Sonata use?
Disconnect the power cord from the bulb base at the back of the assembly. Push the bulb spring on the assembly to remove the light bulb. Pull the old bulb out and place the new bulb in. The low-beam lights use H7 bulbs. The high-beam lights use H1 bulbs.
How do you replace a headlight on a Hyundai Sonata?
Lightly tug on the electrical connector at the rear of Sonata’s headlamp assembly. If the connector comes out, securely plug it into the rear of the assembly. If the headlights are still malfunctioning, you may need to replace the bulb.
Here you will find fuse box diagrams of Hyundai Sonata 2002, 2003 and 2004, get information about the location of the fuse panels inside the car, and learn about the assignment of each fuse (fuse layout) and relay.
What should I do if my Hyundai Sonata starter is not working?
The battery should not drop below 10.5 volts when the key is turned to start. If it does, it means that the battery has a bad cell and needs to be replaced. If it does not have a huge drop in voltage, the battery is fine. Check the fuse for the starter and the starter relay in the under-hood relay box on the driver’s side fender well.
What should the voltmeter be on a Hyundai Sonata?
Set the voltmeter to 20 volts dc. Check the battery—it should have 12.5 volts or more. If it has less than 12.5 volts, the battery or charging system is suspect. It is possible for a battery to show 12.5 or better on voltage and a bad cell, which would kill the amperage output.
Why does my Hyundai Sonata make a clicking sound?
Driving home from work one day at 55miles per hr my engine just stalled out and turned off , since then the engine makes a clicking sound and has lost all power , and the tires make a clicking sound when I turn. See all problems of the 2011 Hyundai Sonata .
Hyundai Sonata owners have reported 116 problems related to engine clicking and tapping noises (under the engine and engine cooling category). The most recently reported issues are listed below. Also please check out the statistics and reliability analysis of Hyundai Sonata based on all problems reported for the Sonata.
What should the voltage of a Hyundai Sonata battery be?
The voltage of the battery on your Hyundai Sonata can be measured precisely with a multimeter. Before the test, the multimeter is set to the voltage range of the battery and connected to its plus and minus poles. Successful testing of the car battery, i.e. checking the voltage, usually results in values of approx. 12 to 13 volts.
Why is the battery on my Hyundai Sonata not working?
If a new car battery has been installed, the battery may not have yet reached its full capacity. There is nothing to worry about. A new battery only develops its full capacity over time. The voltage of the battery on your Hyundai Sonata can be measured precisely with a multimeter.
Why does my Sonata make a clicking sound?
Symptom: When you turn the key to start the engine of your Sonata, you will hear a clicking sound, which is the sound of a bad starter motor. And if the starter motor does not work with a healthy battery, suspect a malfunction of the starter. If the starter fails, it usually needs to be replaced with a new one.
What to do if your fuse box is clicking?
If that relay also clicks constantly, you need to run more tests. If that relay works fine, then the original relay that was in that spot is faulty. Simply replace that relay with a new one. Identify the terminals on the relay. Look at the terminal labels on the relay.
Fuse box located. The fuse box for the lights and other electrical accessories will be found in the backside of multi box located in the left side of driver. Inside the box you will find a list showing the circuits protected by each fuse.
Fuse box located. The fuse box for the lights and other electrical accessories will be found in the backside of multi box located in the left side of driver. Inside the box you will find a list showing the circuits protected by each fuse. fuse box diagram.
Where is the fuse box on a car?
When this happens, you can easily and quickly replace it with a new fuse with no tools and a few minutes of your time. Turn off your car before you replace a fuse. Find the fuse box, located in the passenger compartment under the dashboard on the left of the driver’s side.
What was the original name of the Hyundai Sonata?
The original importer was a unit of the Auckland-based Giltrap Motor Group. There was a version of the Stellar known as the Stellar 88 launched to celebrate the 1988 Summer Olympics in Seoul. After Stellar 88, Hyundai discontinued the Stellar series and changed it to the Sonata series.
What kind of transmission does the Hyundai Sonata have?
Sonata Ling Xiang. Upgraded audio uses a JBL system, and certain navigation packages come with a telecommunications system with Hyundai’s Mozen system. For the North American model, GLS, SE, and Limited trims were offered. A six-speed manual transmission came standard on the GLS, and a six-speed automatic is available.
Where are the fuses in a Hyundai i10?
Fuse box in passenger compartment. Fuse box location. fuse box diagram (-2010). legend. Fuse box diagram (2011-). legend. Integrated cicuit modul (ICM) relay box in passenger compartment (2011-). Fuse box in engine compartment.
Where are the fuses located on a Hyundai Elantra?
Vehicle | Hyundai / Elantra / › 2011-2016. In model years 2001-2016 Hyundai Elantra the main fuses are located in the engine bay. Another fuse box is located under the dashboard on the driver’s side. This applies to Hyundai Elantra model years 2011, 2012, 2013, 2014, 2015, 2016.
Where is the relay box in a Hyundai i10?
Integrated cicuit modul (ICM) relay box in passenger compartment (2011-). Fuse box in engine compartment. fuse box location. fuse box layout (-2010). legend. Fuse box layout (2011-) (engine compartment). Relay box in engine compartment.
Where is the power window relay switch located?
Windows and door locks stopped working. Clicking this will make more experts see the question and we will remind you when it gets answered. You can’t post conmments that contain an email address. An expert who has achieved level 1. An expert who has answered 20 questions. An expert that has over 10 points.
Where is the power window switch on a Hyundai?
A power window switch takes input from the operator and relays this information to a power window motor that is located inside the door. This motor is connected to a lift that is attached to the window, and the lift then drops or raises the window according to your needs.
Why does my Hyundai power window not work?
If a test light is not available each fuse will have to be pulled out and visually inspected. If the problem continues after checking/replacing the fuses, then the PCM is faulty which is a known problem when a battery is wrongly installed. What could prevent only one power window from working when the other three do?
Where is the fuse on a power window?
This is the fuse which supplies power to the purple wire which comes out of the master switch. If the fuse is good pull out the driver side master window switch and check if the purple wire has power which supplies power to both switches. There could be a break where it goes into the door before it reaches the window switch.