When to replace timing belt on 1997 Honda Accord?

The owner’s manual for the 1997 Honda Accord recommends the timing belt for a 1997 model should be replaced after 105,000 miles. It is worth checking regularly for damage, as it may require replacement sooner. Remove the negative cable from the battery.

Where are the timing marks on a Honda Accord?

A pointer is located on the timing cover, just above the crankshaft pulley, and there is a set of marks filed into the edge of the crankshaft pulley. Note that the white mark on the right is the top dead center, or TDC, mark, and the red mark on the left is the 15 degree BTDC mark. The mark we are concerned with is the red 15 degree BTDC mark.

How do you change the timing on a Honda?

The one for the timing adjustment is the two-pin connector. Insert a jumper wire into the connector to connect the two terminals. Attach the timing light’s power cords to the battery terminals. Clip the magnetic pick-up from the timing light to the number one spark plug wire.

Where is the 18 degree mark on a Honda Accord?

On the 1989 Honda Accord, 18 degrees is the middle mark (painted red) of the three marks on the crankshaft pulley. The 18 degree mark should be centered in the timing pointer. Turn off engine and remove the paper clip from the timing connector and unclip the timing light from the battery and spark plug wire.

Where is the timing light on a Honda Accord?

Turn the engine off. Attach the timing light power cables to the battery located in the front of the engine compartment on the passenger side of the 1989 Honda Accord. Clip the timing light’s spark plug wire pickup around the spark plug wire closest to the driver side of the engine.

What should the timing be on a 1989 Honda Accord?

Rotate the distributor to set the timing to 18degrees +/- 2 BTDC (Before Top Dead Center) and retighten the distributor nuts. On the 1989 Honda Accord, 18 degrees is the middle mark (painted red) of the three marks on the crankshaft pulley. The 18 degree mark should be centered in the timing pointer.

How do you install a balance belt on a Honda Accord?

The balance belt installation is more of the same. Loosen the tensioner adjustment nut to allow the tensioner pulley to be moved out of the way. Install the belt using your marks or the alignment pin. Loosen the adjuster to allow the tensioner to work, rotate the crank one turn and tighten the adjustment nut.

How long does it take to replace serpentine belt on Honda Accord?

If it breaks, the water pump stops and the engine will quickly overheat, leaving you stranded on the road. The good news is that the belt is relatively easy to replace. It should take a professional about 10-15 minutes to replace, but it will take the novice about twice as long—at a cheaper price—with the correct tools.

What kind of wrench do I need to remove belt on Honda Accord?

A serpentine belt wrench is definitely optimal here, but a very long handled 12 mm open ended box wrench will work as well. You may need a second person for this part of the job. Put the wrench on the nut in the center of the pulley, and crank back on it clockwise with a significant amount of force. This will loosen the belt for removal. Figure 2.

When does timing belt need to change for Honda Accord?

The timing belt on a Honda Accord generally needs to be replaced about every 60,000-100,000 miles. When it’s time to replace your timing belt, it’s a good idea to ask your mechanic to check the water pump, timing belt, and pulleys all at the same time.

Does a Honda Accord timing chain need to be replaced?

Your car’s engine is full of moving parts that all work in tandem, and it relies on perfect timing in order to function! That’s why your Honda Accord has either a timing belt or a timing chain, which will eventually need to be checked and replaced over the life of your Honda.

Does the Honda Accord come with a timing chain or belt?

Honda Accord Timing Overview (All Model Years) Over the years Honda Accords have come equipped with both engines that have timing belts as well as engines that have timing chains. From model year 2018 and later all Honda Accord engines came equipped with a timing chain.

What to do if your Honda Accord wont start?

It sounds like the coil inside your distributor is causing it, that happened to my 1995 Honda Accord and I had to replace my entire distributor with a new one, don’t go to the dealership they will tax you for $596.00. Go to your local Autozone or O’reilly’s store for around $150.00 or less.

What kind of car is a 1997 Honda Accord?

Repair guides and support for the 5th generation Honda Accord coupe, sedan, and wagon. Drove my Honda accord 1997 to the store when I tried to start the car it was dead.

Where are the fuses on a Honda Accord?

Check all of your fuses, there’s 2 fuse boxes 1 under the hood, 2.) inside either on the kick panel to the left of the clutch, maybe under the steering wheel or behind the glove box. 6.) does the motor sound any different when trying to crank it?

Where can I buy 1997 Honda Accord parts?

You won’t find an easier way to shop for 1997 Honda Accord performance parts, 1997 Honda Accord body parts, interior components, or any type of part for that matter. Get your Accord upgraded or back in pristine shape by shopping Advance Auto Parts.

Why is my Honda Accord EX not starting?

Before we can fix the no-start problem —in this case in a 1996 Honda Accord EX, which serves as a good example—we have to figure out what’s causing the engine to refuse to start. Here is what this owner experienced: My 1991 Honda Accord EX has 178,000 miles with little or no problem until now.

What should I do if my Honda Accord has no spark?

In this case, the owner replaced the fuel pump, but the problem was elsewhere. Don’t be discouraged when this happens. Although it costs more money when you have to replace multiple parts in your car to solve a problem, this is the burden of the DIY mechanic. And think of all the money you’ve saved by working on your own car!

How do you line up timing belt marks?

Turn the crankshaft counterclockwise to make the cam pulley rotate through three teeth, and line up the timing belt marks. Connect the crankshaft and balancer belt-drive sprocket. Align the front and rear balancer pullets with the body of the oil pump. Mount the balance belt. All engine alignment marks must be accurate.

How do you put timing belt on camshaft?

Push on the the adjuster, relieving tension on the timing belt. Slip the timing belt from the pulleys, and discard. Align the crankshaft timing pointer with the camshaft pulley and the flywheel, so you can see the word “Up” at the top. The edge-marks should also line up with the head surface. Put the belt over the tensioners and pulleys.

When to replace timing belt on Honda Odyssey?

An error occurred while retrieving sharing information. Please try again later. OIL LEAK!! Diagnose Replace Gasket VTEC Assembly Honda Odyssey Accord √ fix it angel

When to replace timing belt on Honda Accord?

1997 1998 1999 2000 2001 2002 Honda Accord, Inline 4 cylinder, 2.3L engine. Replacing the timing belt on a 2001 Honda Accord. The belt has snapped so the car would not start. It just cranks over. Did this on December 23, 2015. Friend just needed the timing belt replaced to just get it running.

An error occurred while retrieving sharing information. Please try again later. OIL LEAK!! Diagnose Replace Gasket VTEC Assembly Honda Odyssey Accord √ fix it angel

How do you reduce tension on a timing belt?

Push the balance belt tensioner away from the timing belt to reduce tension. Slip the balance belt from the pulleys; do not crease or bend it. Disconnect the crankshaft balance belt drive. Undo the timing belt adjuster lock-bolt, and loosen the nut. Push on the the adjuster, relieving tension on the timing belt.

What was the model year of the 1996 Honda Accord?

The 1996 Honda Accord continued for 1997 with only one notable change, the return of SE models, a sign that another redesign was in the offing. Unlike past years, however, the 1997 Accord SE coupe and sedan were not top-liners but “value” models, offering some EX features for a few dollars more than the four-cylinder LX versions.

What was the problem with the Honda Accord in 1995?

1995, 1996, 1997 except DX and V6 models: The wire harness for the factory-installed air conditioner may be improperly routed, allow wires to rub against each other; this poses the risk of a short circuit that could lead to overheating, smoke, and a possible fire.

When did the Honda Accord get a makeover?

Evidently, buyers still recognized this Honda as a “class act” among midsize cars. Accord was redesigned for 1994, highlighted by more power and a larger interior with standard dual airbags. Unlike most makeovers, this one did not produce an appreciably larger Honda.

Repair guides and support for the 5th generation Honda Accord coupe, sedan, and wagon. Drove my Honda accord 1997 to the store when I tried to start the car it was dead.

When did the timing belt come out on the Honda CRV?

Between 1997 and 2001 Honda CRV was equipped with a timing belt under the hood. However, starting in the 2002 model year, Honda swapped out the timing belt in favour of the much more durable timing chain. To this day the CRV is still made with a timing chain.

How much does it cost to change timing belt on Honda Civic?

I show you how easy it is to change the Timing Belt and tensioner on this 1998 Honda Civic 1.6L. Timing belt kit (Belt, pulley & tensioner) all cost under “$55” for the parts. The procedure may be different for other vehicles but the principles are the same.

Is there a timing chain in a Honda Accord?

Depending on the model and year of your Honda you may be using a timing chain or a timing belt in your engine. In general, older Hondas tend to have timing belts while many of the newer models have chains but there is some degree of variation. For instance, since 2018 every Honda Accord has had a timing chain in the engine.

When to know when it’s time to change timing belt?

Most models, like those with 3.2-liter engines, do not need their timing belt replaced until they hit 92,000 miles or after six years, whichever comes first. Others can go as long as 105,000 miles before the belt has to be replaced.

When should you get a timing belt change?

The Function of a Timing Belt. The camshaft operates the valves in your engine to let in and out air and gas.
000 miles before the timing belt needs replacement.
Signs a Timing Belt Needs Replacement. If a timing belt is worn out it may begin to slip and severe misfires will occur.

When to replace timing belt?

Every car manufacturer recommends replacing the timing belt after a given time, and it is imperative to take this advice. The time or distance between timing belt replacement depends on the specific make and model of the vehicle, but on average it should be changed every 100,000 miles.

How long does it take to change the timing belt?

Replacing a timing belt can take as little as two hours and as much as six hours, depending on the skill of the mechanic, the make of the vehicle and any additional existing problems.

How do you adjust the balance belt on a crankshaft?

Fasten the belt adjuster, using a bolt from the lower timing belt cover on the arm of the adjuster. Loosen the timing belt and balance shaft nut. Push the balance belt tensioner away from the timing belt to reduce tension. Slip the balance belt from the pulleys; do not crease or bend it. Disconnect the crankshaft balance belt drive.

What is balance shaft seal on Honda Accord?

Installing a retainer plate holds the balance shaft seal in place. The 2.2-liter engine used in the Accord had a balance shaft seal with a tendency to come out of its bore, resulting in a severe oil leak.

How much does it cost to replace timing belt on Honda Accord?

The average cost for a Honda Accord timing belt replacement is between $468 and $634. Labor costs are estimated between $367 and $463 while parts are priced between $101 and $170. This range does not include taxes and fees, and does not factor in your specific model year or unique location. Related repairs may also be needed.

How often do timing belts need to be replaced?

Most timing belts will need to be replaced as part of regular maintenance every 60,000 to 100,000 miles, and most related problems are caused by not replacing it when you’re supposed to. If the timing belt is starting to go bad, the engine will run poorly and the check engine light will likely come on.

Why do you need to replace timing belt on Toyota Highlander?

The timing belt connects the engine’s camshaft and crankshaft, and ensures that they maintain proper timing to keep the engine running smoothly. When you have it replaced, it might be smart to have related work done to help save on labor.

When did Honda balance shaft seal pop out?

It was a 2001 Honda Accord with 2.3 Liter V-Tech engine. It had nearly 180,000 miles on it, but had been well cared for at another shop. The customer showed me the invoice for changing the timing belt and balance shaft belt at 90,000 miles, asking me of course if this were related. In a way it was.

When did the first Honda Accord come out?

Honda Accord, as a series of vehicles, has been produced by the renowned Japanese automobile manufacturer Honda Motor Co., Ltd. since 1976. When the first Honda Accord was released in 1976 to Japanese market, it was a 3-door hatchback to replace the Honda 1300.

Where can I find parts for my Honda Accord?

These Honda Accord car parts are made of finest durable materials to ensure the satisfaction of every Honda Accord enthusiast. All these parts, Honda Accord parts, Honda Accord car accessories parts, and even Honda Accord used parts can be found through online stores. It is the fastest and convenient way to find for your Honda Accord parts.

What kind of timing chain does a Honda Accord have?

If your Honda Accord dates back to 1997-2002, it has a timing belt. If you have a 4-cylinder model from 2003-2007, you engine has a timing chain; if you have the V6 model from those years, it’s a timing belt. An Accord from 2008-2012 with a 4-cylinder engine will have a timing chain, whereas the V6 engine models have a timing belt.

Why does my Honda Accord not turn over?

Listen for common signs like a ticking noise from the engine, or even an engine misfire. The timing belt can also cause your engine to simply not turn over if it has broken. Oil leaks can also be a sign, since engines typically start to leak motor oil from the timing belt cover over time.

The timing belt on a Honda Accord generally needs to be replaced about every 60,000-100,000 miles.

Do you need to replace balance belt on Honda Accord?

These tips outline the belt replacement for the popular 2.2- and 2.3-liter Accord engines. The other Honda engines are similar, but don’t require the balance belt. They shouldn’t present any challenge to the experienced tech, but there are some things to keep in mind as you tackle these jobs.

How much does a timing belt replacement cost?

Know what price you should pay to get your vehicle fixed. The average cost for a Honda Accord timing belt replacement is between $482 and $633. Labor costs are estimated between $378 and $478 while parts are priced between $104 and $155. Estimate does not include taxes and fees.

What happens when the timing belt jumps on a car?

On some engines, if the timing belt has jumped, the pistons and valves can collide and there will be noise and damage. These engine designs are referred to as interference engines.

These tips outline the belt replacement for the popular 2.2- and 2.3-liter Accord engines. The other Honda engines are similar, but don’t require the balance belt. They shouldn’t present any challenge to the experienced tech, but there are some things to keep in mind as you tackle these jobs.

On some engines, if the timing belt has jumped, the pistons and valves can collide and there will be noise and damage. These engine designs are referred to as interference engines.

Navigation