What was the speed sensor on a 1993 Jeep Grand Cherokee?
1993, 1994, 1995 4.0L Jeep Grand Cherokee. The powertrain control module (PCM) feeds 8 Volts DC to the vehicle speed sensor (VSS) thru’ the WHT/BLK (white with black stripe) wire. NOTE: The WHT/BLK wire also feeds the crankshaft position (CKP) sensor and the camshaft position (CMP) sensor with 8 Volts DC.
Why is the Speedo cable on my Jeep Cherokee not working?
No speedo cable. They are electronic after 91. When you moved your grounds did you grind of the paint under the ground connector? okay well im out of answers. No speedo cable. They are electronic after 91. When you moved your grounds did you grind of the paint under the ground connector?
Why does my speedometer not work with a new sensor?
Had check engine light come on. Ran codes came up with p1692 speedo sensor. Put new sensor and still speedometer will not work. Any suggestions please. I dont want to buy a new pcu unless I have to.
Why is the instrument cluster on my Jeep Cherokee not working?
The cluster has stopped working again too. I decided to hook my OBD2 scanner up figuring there was probably a code and I pulled the following: P1686, P1694, P1698. All of them have to do with the PCM not communicating with the instrument cluster.
1993, 1994, 1995 4.0L Jeep Grand Cherokee. The powertrain control module (PCM) feeds 8 Volts DC to the vehicle speed sensor (VSS) thru’ the WHT/BLK (white with black stripe) wire. NOTE: The WHT/BLK wire also feeds the crankshaft position (CKP) sensor and the camshaft position (CMP) sensor with 8 Volts DC.
When did the Jeep Grand Cherokee 4.0 come out?
4) specs Jeep Grand Cherokee 4.0 Limited Quadra-Trac automatic (aut. 4) , manufactured or sold in 1994, version for Europe (until mid-year 1994)
What are the specs of a 1994 Jeep Laredo?
1994 Jeep Grand Cherokee Laredo 4×4 4.0L Command-Trac automatic (aut. 4) specs Jeep Grand Cherokee Laredo 4×4 4.0L Command-Trac automatic (aut. 4) , model year 1994, version for North America U.S. manufactured by Jeep in USA 5-door wagon body type
What was the mileage of a 1994 Jeep?
1994 Jeep Cherokee Sport. 4X4 4.0L 6cyl 21+ MPG. 86,000 Original documented mileage. 1 Original owner.
What are the pins on a 1993 Jeep Grand Cherokee?
1993, 1994, 1995 4.0L Grand Cherokee 60 Pin Connector Pin Wire Color Description 1 RED/WHT MAP Sensor Signal 2 TAN/BLK ECT Sensor 3 PNK/BLK RED Battery Power ( 1993 Only) Battery Power 4 BLK/LT BLU Sensor Ground
How many pins does a Jeep Grand Cherokee PCM have?
The PCM has a 60 pin connector and on the back side of the connector (wire side) are embossed a few numbers to further aid you in correctly identifying the pins (circuits). IMPORTANT: The illustration above and pin-out table below apply only to: 1993, 1994, 1995 Jeep Grand Cherokee with 4.0L engine.
Why is my speedometer not working on my Jeep?
The ECU is programmed with your Grand Cherokee’s gear ratios and stock tire height. It combines this data to send the speed reading to the instrument cluster. The causes of a bad speedometer will typically be found in these four things:
What is the ECU on a Jeep Grand Cherokee?
ECU – Your Grand Cherokee’s Engine Control Unit (ECU for short) is the computer that takes all of the information that the vehicle sensors compile and uses it to control the vehicle systems, and sends important vehicular telemetry data to the driver via the instrument cluster.
What kind of transmission does a Jeep 3, 4 and 5 have?
Jeep/AMC 3, 4 and 5 speeds: Top loaded, cast iron case with non-synchronized 1st gear and 24 tooth 2nd/3rd syncro rings. Main shaft 1st/Reverse gear has 25 helical or straight cut teeth.
Where can I find the Jeep transmission ratio?
In addition to the below information you can find Jeep manual transmission ratio and size data on our site at: Jeep ratio data Jeep identification tag cross reference information is alos available. Jeep/AMC 3, 4 and 5 speeds: Top loaded, cast iron case with non-synchronized 1st gear and 24 tooth 2nd/3rd syncro rings.
What kind of transmission is in a 1986 Jeep?
Used in 4 cylinder applications except 1986 6 cylinder. Front input bearing outside diameter is 80mm. End loaded, aluminum case transmission based on the Toyota “R” series. Used in 6 cylinder applications. Front input bearing outside diameter is 90mm. Aluminum case that is split vertically lengthwise.