What to do when your PassLock security light goes out?
The Body Control Moudle should re-learn the security signal, and the “SECURITY” light should go out. When it does, Turn the ignition OFF for five (5) seconds, and then try to re-start the car. The “SECURITY” light should remain off this time, and the car should keep running. If not, don’t give up.
What causes a security light to not turn off?
Some security light problems that require a professional include: 1 Problems with the electrical wiring 2 Damage caused by a power surge 3 Improper installation 4 The security light needs to be replaced due to normal wear and tear
Why does the security light flash when the ignition is off?
On some vehicles, it will flash when the ignition is off, and the OEM security is activated. Its other main purpose is to indicate that the security of your vehicle may have been compromised, and the engine has been immobilized to prevent potential theft. Don’t assume right away that it means someone tried to break into or steal your vehicle.
Why is the security light on on my car?
The security light on your vehicle serves has two purposes. On some vehicles, it will flash when the ignition is off, and the OEM security is activated. Its other main purpose is to indicate that the security of your vehicle may have been compromised, and the engine has been immobilized…
What should I do if my PassLock security light goes off?
If nothing happens or the engine starts and dies, the security light will be flashing. Wait ten minutes. The flashing light should go off or illuminate without flashing. When it does, turn the ignition off, wait twenty seconds, and then try to start the engine. If it starts and runs, everything is okay.
Some security light problems that require a professional include: 1 Problems with the electrical wiring 2 Damage caused by a power surge 3 Improper installation 4 The security light needs to be replaced due to normal wear and tear
Is it normal for the security light to go off when the engine is running?
After the learn procedure is completed and the engine is running, the security light may stay on steady for a few minutes and then go off—this is normal. Depending on the system, replacement of key components will necessitate that a relearn procedure be completed.
How can I adjust the sensitivity of my security light?
Step 1: Adjust the sensitivity settings Most security lights have a sensitivity setting on the sensor head or under the light fixture. These can usually be controlled with a small dial (this dial may also be labeled “range” and will look something like this).
Can You disable the PassLock on a GM car?
The following instructions will allow you to disable the PassLock security in quite a few GM Vehicles. •This will allow you to install a remote starter and not have to purchase a bypass. •Avoid Costly repairs for an already broken PassLock System.
Is there a way to disable Sunfire theft protection?
Anti-theft systems protect vehicles from intruders entering and breaking in to your car. False alarms may prevent you from turning on your own vehicle, and you may want to disable your anti-theft system to prevent these types of issues. Disabling the anti-theft system in a Sunfire can be done in a few steps. Insert your key into the ignition.
When do you turn off the PassLock system?
The vehicle learns the Passlock Sensor Data Code and/or resistance on the next ignition switch transition from OFF to CRANK. You must turn the ignition OFF before attempting to start the vehicle. 12. Your all done, Solder all your new connections.
The vehicle learns the Passlock Sensor Data Code and/or resistance on the next ignition switch transition from OFF to CRANK. You must turn the ignition OFF before attempting to start the vehicle. 12. Your all done, Solder all your new connections.
The following instructions will allow you to disable the PassLock security in quite a few GM Vehicles. •This will allow you to install a remote starter and not have to purchase a bypass. •Avoid Costly repairs for an already broken PassLock System.
Anti-theft systems protect vehicles from intruders entering and breaking in to your car. False alarms may prevent you from turning on your own vehicle, and you may want to disable your anti-theft system to prevent these types of issues. Disabling the anti-theft system in a Sunfire can be done in a few steps. Insert your key into the ignition.
Is there a way to bypass PassLock 2?
The easiest way to bypass the Passlock 2 system is to place a resistor between the passlock sensing wire and the ground reference wire. To find these wires, look for three wires that at some point are wrapped together, coming from the ignition barrel. Usually, they are orange/black, red/white, and black.
Why does my motion detector light stay on all the time?
The wind blowing though the leaves can cause the detector to sense motion, keeping the light on. Make sure the motion light is mounted to a sturdy service. A surface that moves can create false triggers and turn on the light.
How to reset a motion light that stays on all the time?
Check the time switch to confirm it isn’t set in “Test” mode. If set in “Test” mode, move the switch to a pre-determined time setting. The “Test” mode could cause the light to come on and remain on. Reset the light to make sure it isn’t set to manual operation. Turn off the light switch that operates the motion light.
Why does my car stall with the security light on?
It should start, and then stall, with the “SECURITY” light flashing. (In rare cases, the car may keep running and the security light will not illuminate, but that only happens if you are very lucky.)
Why does my PassLock security light keep going off?
After turning the ignition off for the third time and waiting for twenty seconds, the engine should start and run. If it doesn’t, there may still be something wrong with the system. After the learn procedure is completed and the engine is running, the security light may stay on steady for a few minutes and then go off—this is normal.
Check the time switch to confirm it isn’t set in “Test” mode. If set in “Test” mode, move the switch to a pre-determined time setting. The “Test” mode could cause the light to come on and remain on. Reset the light to make sure it isn’t set to manual operation. Turn off the light switch that operates the motion light.
The wind blowing though the leaves can cause the detector to sense motion, keeping the light on. Make sure the motion light is mounted to a sturdy service. A surface that moves can create false triggers and turn on the light.
The Body Control Moudle should re-learn the security signal, and the “SECURITY” light should go out. When it does, Turn the ignition OFF for five (5) seconds, and then try to re-start the car. The “SECURITY” light should remain off this time, and the car should keep running. If not, don’t give up.
What to do if your anti theft system is locked up?
If the anti-theft system has locked up your engine, you won’t be able to start it. You’ll have to disable it with these steps. Step 1: Check for the anti-theft light. It’s located on your dash and will have a blue or red light. Step 2: Turn the ignition to the “on” position.
Can a PassLock be used on an ignition lock?
No programming is required for the PASSLock-equipped vehicle to accept additional keys. Any key blank with the proper profile cut to the correct depths can be used to operate the ignition lock.
How to relearn the PassLock sensor data code?
Observe the SECURITY telltale, after approximately 10 minutes the telltale will turn OFF. Turn OFF the ignition, and wait 5 seconds . Repeat steps 1 through 4, 2 more times for a total of 3 cycles/30 minutes. The vehicle is now ready to relearn the Passlock Sensor Data Code and/or passwords on the next ignition switch transition from OFF to CRANK.