What should I do if my Saturn ignition switch is not turning?

If you had to assemble the lock cylinder with the ignition switch housing, you may also need to reconnect those pieces again if the key is not turning all the way through to the ignition position. Assemble the rest of the steering column housing pieces back into place on your Saturn.

Where is the fuse on a Saturn ignition?

Open the fuse panel under the steering column by turning the knob on the fuse panel counterclockwise and pulling down on the cover. Locate the fuse for the starter in the fuse panel using the fuse diagram on the underside of the fuse panel cover. Remove the fuse using a fuse puller in the fuse box.

What to do if you have ignition switch problem?

If you are experiencing problems with your ignition key or switch, you may need a simple key reset or you could have a faulty ignition switch that needs to be replaced. Open the fuse panel under the steering column by turning the knob on the fuse panel counterclockwise and pulling down on the cover.

Can a negative battery be removed from a Saturn?

Remove the negative battery cable from your Saturn’s battery. If you want to be doubly safe, remove the positive battery cable as well. Wait for at least 15 minutes before touching any electrical parts or connections.

How does the ignition switch work on a Saturn?

Saturn vehicles use a transponder inside the ignition key to prevent unauthorized engine starting. There is a component inside the dash and linked to the ignition switch that sends a signal to the starter motor allowing the vehicle to start.

What should I do if my Saturn ignition is not working?

Turn the ignition key and try to start the engine. If the battery is known to be fully charged, the Saturn should start. If there is an error in the ignition switch, you will not hear the typical faint “click” when you initially turn the ignition key to the “III” position to crank the engine.

Can a faulty ignition switch cause a car to not start?

There is a component inside the dash and linked to the ignition switch that sends a signal to the starter motor allowing the vehicle to start. If you are experiencing problems with your ignition key or switch, you may need a simple key reset or you could have a faulty ignition switch that needs to be replaced.

How do you remove an ignition lock cylinder?

Step 8: Loosen the screws on top of the ignition lock assembly. The lock cylinder is secured to the lock assembly by a button on the bottom of the housing and two screws on top of the lock assembly. Loosen the two screws on top to allow you to remove the cylinder.

What causes a fault in an ignition lock cylinder?

Most of the time, when a problem occurs within the ignition system, it will be caused by a fault within the ignition lock cylinder. Inside the lock cylinder are a series of tumblers where the key is inserted.

Where is the starter fuse on a Saturn?

How do you replace an ignition switch on a car?

Slide the new ignition switch assembly into place, making sure you reconnect all of the necessary electrical connections and put the new ignition switch in exactly the same location as the old one was located. Tighten the bolts to securing it in place. Reconnect the negative and positive battery terminals and try your new ignition switch.

How does the ignition switch work on a GM car?

The ignition switch now talks to the body control module (BCM) and it’s the BCM that initiates one of two relays. The second relay, the more important of the two, is controlled by the powertrain control module (PCM). And it only operates the starter relay after it’s satisfied that the correct key is in the ignition.

Where is the ignition lock cylinder located on a car?

The ignition lock cylinder is located inside the assembly or lock body that is often welded onto the steering column. Most of the time, when a problem occurs within the ignition system, it will be caused by a fault within the ignition lock cylinder. Inside the lock cylinder are a series of tumblers where the key is inserted.

Where is the cover on the ignition switch?

On most vehicles, there is a plastic or metal cover on the ignition lock cylinder. Remove the small screw that holds this cover on, typically located on the bottom of the switch. Once the screw has been removed, carefully slide the cover off the ignition lock cylinder.

What should I do if I need to replace my ignition switch?

Reconnect the cable to the negative (-) terminal on the battery, then insert the key into the ignition and turn it to start the vehicle. The vehicle should start without any issue. If it doesn’t, remove the ignition switch and reinstall it. Shut the engine off (if it starts) and disconnect the battery again.

Where can I get a new ignition key for my Saturn Vue?

Order a new ignition/key online and have a mechanic or locksmith install and code it for you (if necessary). A word of caution: The type of key you need depends on the year and model of your Saturn Vue. Therefore, the options for getting a new key made and programmed depends on whether you need a transponder or a regular key.

Do you need a fob code for a Saturn Vue?

For Saturn Vue vehicles equipped with a transponder system and/or remote, intelligent key, or fob key, codes are available. However, programming is necessary. You will have to either tow the car to the dealer or have an automotive locksmith come and program the key on site.

What was the year of my Saturn Vue?

Non-Transponder Key: 2002 to 2007. Please keep in mind that while some keys or keys may look the same, they have different capabilities/frequencies/keyways. Therefore, having the right key is essential. Click on the type of key you had or your year model below to get the most accurate information:

Navigation