What is the slave hose for a Datsun clutch?
Slave hose is part#1669.Click here to view cheaper aftermarket alternative. 65 – 70 Clutch master cylinder. Copper sealing washers for brake hoses and clutch slave hose.
How do you Bleed the clutch line on a Nissan?
Once the clutch line is back into the master cylinder, proceed to bleed the clutch lines. You can now reconnect the clutch cylinder and the clutch pedal, via the pin and clip. Start pumping your clutch pedal and you should be able to feel pressure. Keep pumping and keep an eye on your master cylinder, keeping it topped up.
What kind of clutch do I need for a Datsun 1600?
Roadster needle roller pilot bearing crankshaft for high performance clutch set up. Early 1500 / 1600 2 3/8 hole spacing slave Cylinder, Hose & washer Kit.NOTE: Clutch slave does not have stand off for the clutch spring as used on the 1600 models. Economical aftermarket clutch master with aftermarket 2″ center to center hole slave cylinder.
Where is the hole on a Datsun clutch?
Hole center to center 2 ” Includes rod. Brake & clutch master cylinder pin. Replacing the old worn pin will reduce further wear to the master cylinder push rod on the back of the master cylinder. You probably should check the master cylinder push rod to see if it is egged out.
Roadster needle roller pilot bearing crankshaft for high performance clutch set up. Early 1500 / 1600 2 3/8 hole spacing slave Cylinder, Hose & washer Kit.NOTE: Clutch slave does not have stand off for the clutch spring as used on the 1600 models. Economical aftermarket clutch master with aftermarket 2″ center to center hole slave cylinder.
Slave hose is part#1669.Click here to view cheaper aftermarket alternative. 65 – 70 Clutch master cylinder. Copper sealing washers for brake hoses and clutch slave hose.
Once the clutch line is back into the master cylinder, proceed to bleed the clutch lines. You can now reconnect the clutch cylinder and the clutch pedal, via the pin and clip. Start pumping your clutch pedal and you should be able to feel pressure. Keep pumping and keep an eye on your master cylinder, keeping it topped up.
What’s the clutch sleeve on a Datsun 5 speed?
2000 Clutch T/O bearing sleeve for 5 speed. Also 510, 521, 620, pick up truck. 1600 or 2000 Clutch T/O Bearing sleeve spring. 1600 or 2000 Clutch arm spring. Clutch pressure plate bolt 67 1/2 – 70 (6). 2000 Clutch arm 5 speed transmission housing boot. Will not harden and deteriorate like the Nissan counterpart. Lifetime warranty. BACK IN STOCK !
What kind of clutch does a Datsun Roadster use?
OEM clutch master, slave cylinder, slave hose, hose copper sealing washer,slave rod, rod nut and pal nut & spring. Roadster needle roller pilot bearing crankshaft for high performance clutch set up.
Where are the hoist brackets on a Datsun?
Attach an engine hoist capable of lifting up to 8-feet or higher to the two hoist brackets located on the engine. One is on the front near the idler pulley and the second is at the back of the engine behind the air cleaner assembly.
How much does a Nissan 2000 HD clutch cost?
The following kit includes: Nissan 2000 HD 650 KILOGRAM pressure plate from Datsun comp, OEM T/O bearing, OEM pilot bearing, high quality Japanese clutch disc/better than cardboard Nissan disc. Order by PART# 1483B $490.00 NOTE:Photos match order of description in text.
How big is the clutch on a Datsun?
4 speed transmission clutch arm boot. This boot fits Transmission Case Thickness: .160″ (5/32″) Hole Size: 2 3/8″ x 1 5/8″ the transmissions with the smaller 5/32 thick housing. For the other 4 speed boot with the wider spacing of 1/4 of a inch see part number 2194.
How big is the clutch spring on a Nissan 2000?
1600 or 2000 Clutch T/O Bearing sleeve spring. 1600 or 2000 Clutch arm spring. Clutch pressure plate bolt 67 1/2 – 70 (6). 2000 Clutch arm 5 speed transmission housing boot. Will not harden and deteriorate like the Nissan counterpart. Lifetime warranty. BACK IN STOCK ! We sell the Nissan 2000 Heavy duty clutch kit for 1600 & the 2000 models.
Attach an engine hoist capable of lifting up to 8-feet or higher to the two hoist brackets located on the engine. One is on the front near the idler pulley and the second is at the back of the engine behind the air cleaner assembly.