What is the diagnostic code for a 2007 Harley Davidson?
2007 Harley Davidson Diagnostic Trouble Codes (from Service Manual 99497-07) Getting Codes: 1- Turn Ignition switch to OFF & Run/Stop switch is to Run. 2- Push odometer reset button in & hold. 3- Turn ignition switch to Ignition and release odometer reset button.
How to get the ECM code on a Harley Davidson?
The following procedure will instruct in retrieving and clearing ECM Diagnostic Trouble Codes and TSM/TSSM codes through the Harley guage cluster as well as a list of codes. 1- Turn Ignition switchto OFF & Run/Stop switch is to Run. 2- Push odometer resetbutton in & hold. 3- Turnignition switchto Ignition and release the odometer reset button.
How do you find out if your Harley Davidson has a code?
NOTE: To determine if a code is current or historic, clear the displayed code by pushing in and holding the odometer reset button ( longer than 5 seconds) until ‘clear’ comes up. Release the odometer reset button. Turn OFF the ignition switch.
What does the Check Engine light on a Harley Davidson mean?
Background lighting should illuminate, speedometer needle should sweep its full range and indicator lamps (battery, security, low fuel, check engine and cruise) should illuminate. The word “diag” should then appear.
2007 Harley Davidson Diagnostic Trouble Codes (from Service Manual 99497-07) Getting Codes: 1- Turn Ignition switch to OFF & Run/Stop switch is to Run. 2- Push odometer reset button in & hold. 3- Turn ignition switch to Ignition and release odometer reset button.
The following procedure will instruct in retrieving and clearing ECM Diagnostic Trouble Codes and TSM/TSSM codes through the Harley guage cluster as well as a list of codes. 1- Turn Ignition switchto OFF & Run/Stop switch is to Run. 2- Push odometer resetbutton in & hold. 3- Turnignition switchto Ignition and release the odometer reset button.
What to do if you get an error code on your Harley Davidson?
Turn OFF the ignition switch. Run your bike and shut it down then recheck the DTCs again by repeating steps 1 to 9. If the code is current it will reappear. Press and release the odometer reset button to continue to the next module. Turn Ignition switch to OFF.
What does the Code 02 mean on a Harley Davidson?
If it were a current code, the light would remain lit while running. Above codes can also be set if 02 sensor fails. CKP – Crank Position Sensor. The CKP generates an “AC signal” which is sent to the ECM where it is used to reference engine position (TDC) and speed.
How to get the DTC code on a Harley Davidson?
6 – To get the DTC within an area of diagnostics, push and hold the odometer resetbutton in for 5 seconds and release. If there are any DTC’s the code will be displayed or the word “none” will appear if there are no DTC’s. Push the odometer resetbutton again to view additional codes if they exist. 7 – Record the codes.
How to reset the odometer on a 2004 Harley?
Background lighting sould illuminate, speedometer needle should sweep its full range and indicator lamps (battery, security, low fuel, check engine and cruise) should illuminate. The word “diag” should then appear. 4 – Push the odometer reset button once and you will see the selection menu “PSSPt” with the first P flashing.
6 – To get the DTC within an area of diagnostics, push and hold the odometer resetbutton in for 5 seconds and release. If there are any DTC’s the code will be displayed or the word “none” will appear if there are no DTC’s. Push the odometer resetbutton again to view additional codes if they exist. 7 – Record the codes.
Background lighting sould illuminate, speedometer needle should sweep its full range and indicator lamps (battery, security, low fuel, check engine and cruise) should illuminate. The word “diag” should then appear. 4 – Push the odometer reset button once and you will see the selection menu “PSSPt” with the first P flashing.