What is a Yamaha Blaster tors system?
TORS, or throttle override system, is a safety feature pioneered for use on high-speed Yamaha vehicles such as snowmobiles and ATVs, which use a pull-throttle cable system instead of a hard linkage.
What is a tors eliminator kit?
TORS Stands for Throttle Over Ride System, this electrical system is commonly found in ATV applications in the case the throttle malfunctions, the TORS system will shut off spark to the motor. Our unique kit contains a replacement carb cap, idle screw kit, and throttle cable for increased performance and control.
Where is the idle screw on a Yamaha Blaster?
This small brass screw is located on the left side of the carburetor right beside the choke lever. Turn the screw using the flat head screwdriver. When the screw is turned to the right the engine rpm will increase.
Is a Yamaha Blaster fast?
For a simple ATV, Yamaha Blasters can go pretty fast. At top speed, it can reach about 55 mph. With a little fixing up and maintenance, you can get it to 30 to 40 hp. Modifying enough can help you bump up its horsepower to 45 hp.
How do you remove the tors from a Yamaha Blaster?
All you need is a philips screwdriver and something to cut wire with.
- Remove your front plastic and unplug the TORS “brain”.
- This wire comes off of your carb and is part of your TORS.
- Next either cut this wire or take the 3 screw out of the top of the throttle box and take the switch out of the middle.
What does tors do on a banshee?
The TORS is the Throttle Override System. It’s mainly the little black box above the left carb, simply unplug it to deactivate it. It is supposed to electronically reduce the throttle if the throttle sticks open but most people remove it because its usually the route of many problem’s.
How do you delete tors on Blaster?
How do you adjust the float on a Yamaha Blaster?
slightly bend the center tab that the float needle hangs on, and remeasure. bend it down into the carb for a higher float height measurement, and up for a lower float height measurement, (the lower the measurement, the more fuel will be allowed into your fuel bowl, get it exact for correct fuel level)…………
Are Yamaha Blasters reliable?
speedracinshift Member. i agree yes they are very reliable one main thing is that people ride the crap out of them and they run it lean on the topend so they burnit up or they just dont take care of the bike theres a lot of factors, if your bike is tuned and taken care of then it will last longer.
What does the Tors system on a Yamaha snowmobile do?
TORS System Basics. TORS, or throttle override system, is a safety feature pioneered for use on high-speed Yamaha vehicles such as snowmobiles and ATVs, which use a pull-throttle cable system instead of a hard linkage. A TORS unit uses a throttle position sensor to check the position of the throttle on your handlebars;
Where is the Black Box on a Yamaha Tors?
There are two ways to find it: you can either follow the throttle cable from the hand-throttle to the back of the TORS unit, or you can follow the wires from the throttle position switch to the TORS’ “black box” control unit. The wires from the black box go into your Yamaha’s TORS control unit.
When to use a tors on an ATV?
While the TORS works admirably when new, years of dirt, mud and hard landings can turn the system into more of a liability than a safety feature. TORS, or throttle override system, is a safety feature pioneered for use on high-speed Yamaha vehicles such as snowmobiles and ATVs, which use a pull-throttle cable system instead of a hard linkage.
What makes a Yamaha Tors control unit fail?
The microswitch in the handlebars, the TORS control box, the TORS unit and all of the wiring in between offer numerous opportunities for failure. Computers and electronic control systems generally don’t get along with the average ATV’s operating conditions, which over time, make TORS failure almost inevitable.